Extreme Networks BlackDiamond 6816 Installations- und Betriebshandbuch

Part Number: 121069-00 Rev 01 1

MSM-3 Upgrade Note

This note describes the minimum requirements and upgrade procedures for the BlackDiamond®

MSM-3. For complete product documentation, see:

http://www.extremenetworks.com/go/documentation_main.htm

BootROM 8.1 and ExtremeWare 7.1.1 Required

The MSM-3 requires both BootROM 8.1 (or later) and the final release build of ExtremeWare 7.1.1 (or

later). Builds prior to the final release might not fully support the MSM-3.

You can obtain BootROM 8.1 and ExtremeWare 7.1.1 from the Extreme Networks website at:

http://www.extremenetworks.com/go/esupport.htm

Enter your username and password from your current support contract. Once logged in, select Software

Download and download the files.

You can contact Extreme Networks Customer Support at: (800) 998-2408 or (408) 579-2826.

Upgrade Your Chassis

You need the following tools and equipment to install an MSM-3:

•ESD-preventive wrist strap

•# 1 Phillips screwdriver

•MSM-3

To install an MSM-3 in a new chassis, simply follow the installation instructions in the BlackDiamond

Module Installation Note included with your MSM-3. To upgrade your chassis from MSM64i’s to

MSM-3’s:

1Preserve Your Existing Configuration

2Upgrade to MSM-3’s

3Verify the Installation

These procedures are described in the following sections.

2MSM-3 Upgrade Note

Upgrade Your Chassis

CAUTION

Service to BlackDiamond modules should be performed by trained service personnel only. Before

installing or removing any components of the system, or before carrying out any maintenance

procedures, you must read the safety information provided in Appendix A of the Extreme Networks

Consolidated Hardware Guide.

Preserve Your Existing Configuration

To preserve your existing configuration, follow these steps:

1Upgrade the MSM64i’s to ExtremeWare 7.1.1 (or later) and BootROM 8.1 (or later). Follow the

instructions in the Release Notes for the release you are installing.

2Make any configuration changes required by the upgrade.

3Save the configuration using the save configuration command.

4Upload the configuration to a TFTP server using the upload configuration command.

5Verify that the uploaded file is complete.

6Start a console log.

7Capture the real-time status of the switch using the show tech-support command.

8Stop the console log.

Upgrade to MSM-3’s

To upgrade your chassis from MSM64i’s to MSM-3’s:

1Attach the ESD strap to your wrist and connect the metal end to the ground receptacle that is located

on the top-left corner of the switch front panel.

2Remove the slave MSM64i. On a BlackDiamond 6816, remove all slaves.

3Insert the MSM-3. On a BlackDiamond 6816, insert MSM-3’s into all empty slots. Each MSM-3

initializes as a slave MSM.

NOTE

Using an MSM64i and MSM-3 in the same chassis is supported during the upgrade process only. If

you use both MSMs in the same chassis, the switch does not operate as expected, and generates a

warning similar to the following at login:

WARNING: An MSM module type mismatch has been detected.

Slots MSM-A and MSM-B must both contain MSM-3's or MSM64i's.

This module type mismatch is only supported while

migrating from MSM64i's to MSM-3's.

The MSM-3 features Cross Module Trunking and Hitless Failover

will NOT operate in this configuration.

4Copy the upgraded ExtremeWare, BootROM, and configuration from the MSM64i to the MSM-3

using the synchronize command.

Upgrade Your Chassis

MSM-3 Upgrade Note 3

NOTE

An MSM-3 will not operate with ExtremeWare versions prior to 7.1.1 or BootROM versions prior to

8.1. If you inadvertantly load the wrong ExtremeWare or BootROM image, upgrade the master

MSM64i to the correct images and synchronize again.

5Force the MSM64i to fail over to the MSM-3 using the run msm-failover command.

6Remove the MSM64i that has just become the slave.

7Install another MSM-3. It initializes as the slave MSM.

8Copy the upgraded ExtremeWare, BootROM, and configuration from the master MSM-3 to the slave

MSM-3 using the synchronize command.

Verify the Installation

After you install an MSM-3, verify that it is working correctly by checking the LEDs on the front panel.

If the MSM-3 is operating normally, the front-panel LED indicators appear as follows:

•SYS LED—green blinking

•MSTR LED:

—Green: Operating as master

—Amber: Operating as slave

•ENV—green

•ERR—off

•Link/Activity:

—Green: Link is up

—Amber: Packet activity is occurring

Andere Handbücher für BlackDiamond 6816

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extreme Networks Schalten Handbücher

Extreme Networks

Extreme Networks BlackDiamond 8810 Handbuch

Extreme Networks

Extreme Networks ExtremeAccess Series Handbuch

Extreme Networks

Extreme Networks B-Series B5 Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeSwitching X440-G2 Series Handbuch

Extreme Networks

Extreme Networks 3626 Bedienungsanleitung

Extreme Networks

Extreme Networks X460-G2 Series Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeSwitching CES 2000 Series Handbuch

Extreme Networks

Extreme Networks BlackDiamond X8 Series Montageanleitung

Extreme Networks

Extreme Networks Summit 200-24 Bedienungsanleitung

Extreme Networks

Extreme Networks Summit X350-24t Bedienungsanleitung

Extreme Networks

Extreme Networks Summit WM200 Bedienungsanleitung

Extreme Networks

Extreme Networks Summit 200-24 Handbuch

Extreme Networks

Extreme Networks ReachNXT 100-8t Bedienungsanleitung

Extreme Networks

Extreme Networks ReachNXT 100-8t Bedienungsanleitung

Extreme Networks

Extreme Networks Summit X450-G2-24t-GE4 Bedienungsanleitung

Extreme Networks

Extreme Networks Summit Summit48si Bedienungsanleitung

Extreme Networks

Extreme Networks Summit X250e-24p Referenzhandbuch

Extreme Networks

Extreme Networks ExtremeSwitching Virtual Services Platform 4850GTS... Bedienungsanleitung

Extreme Networks

Extreme Networks Alpine 3802 Handbuch

Extreme Networks

Extreme Networks Summit Summit1i Handbuch

Extreme Networks

Extreme Networks BlackDiamond 8800 Series Handbuch

Extreme Networks

Extreme Networks Summit X430 Series Kurzanleitung

Extreme Networks

Extreme Networks Summit1 Handbuch

Extreme Networks

Extreme Networks Summit X150-24t Handbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch