Extron electronics SW4 3G HD-SDI Bedienungsanleitung

AUTO

SWITCH

ACTIVE

SW4 3G HD-SDI

MULTI-RATE SDI SWITCHER

MODE

NORMAL

AUTO

RATE

NOT

RECOGNIZED

270 Mbps

1.485 Gbps

2.97 Gbps

The Extron® SW4 3G HD-SDI switcher is a four input, two parallel output, multi-rate switcher. It allows up to four SDI or

HD-SDI video input sources to be switched to two identical outputs, on female BNC connectors. The SW4 HD-SDI supports

multiple SDI rates, including 270 Mbps, 1.485 Gbps, and 2.97 Gbps. In auto-input switch mode, the SW4 3G automatically

switches to the highest numbered input with active sync pulses.

This guide provides basic instructions for an experienced installer to set up and operate this switcher.

Installation

1. Turn off all of the equipment and disconnect it from the power source.

2. (Optional) If desired, mount the switcher on a 6 inch or 9.5 inch deep rack shelf.

3. Connect up to four SDI, HD-SDI, or 3G-SDI video inputs to BNC input connectors 1 through 4.

NOTE: Each input is equalized regardless of the rate.

4. Connect one or two video SDI, HD-SDI, or 3G-SDI output devices to the

rear panel BNC output connectors.

NOTE: Outputs 1 and 2 output identical signals.

5. If the switcher will be connected to a computer or host controller for

remote control, wire the provided 3-pole captive screw connector to an

RS-232 cable. Connect the RS-232 cable to the RS-232 port on the rear

panel of the switcher and to the host RS-232 port (see the illustration at

right).

Protocol for the RS-232 port: 9600 baud, 8 data bits, 1 stop bit, no parity

6. Power on the input and output devices, then connect power to the

switcher by connecting the provided IEC power cord to the switcher

power connector and to an AC outlet.

Connecting an Input to the Outputs

To create a tie between an input and the outputs:

1. Determine the necessary switch mode for the SW4 3G (the default mode is normal). (See “Enabling and Disabling

Auto-input Switch Mode,” on the reverse side.)

оSelect auto-input switch mode to automatically switch to the highest numbered input with active sync pulses.

оChoose normal mode to manually change the input.

2. Select an input.

оIf you are using normal mode, select the desired input by pressing and releasing its input button. The LED beside

the selected input button lights.

оTo switch to another input, press a different input button.

оIf you are using auto-input switch mode, no action is necessary. The switcher automatically switches to the highest

numbered active input.

3. If needed, create a remote connection via RS-232. (See step 5 under “Installation,” above.)

Figure 1. RS-232 Connection

Switcher

Receive

Transmit

Ground

RS-232

Tx Rx

DB9 connector (female)

pinout to control equipment

Computer

5 1

9 6

Pin RS-232 Function

1 —

2 Rx Receive data (+)

3 Tx T

ransmit data (–)

4 —

5 Gnd Signal ground

6 —

7 — —

8 — —

9 — —

—

INPUTS

1 2 1 23 4

100-240V~.5A MAX.

50/60 Hz

OUTPUTS

RS-232

Tx Rx

SW4 3G HD-SDI • Setup Guide 1

SW4 3G HD-SDI Setup Guide

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517

FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Enabling and Disabling Auto-input Switch Mode

In auto-input switch mode, the SW4 3G automatically switches to the highest numbered input with active

sync pulses. When auto-input switch mode is enabled, the Auto Switch Active LED (shown at right) lights.

Selecting Auto-input Switch Mode

To turn on auto-input switching:

1. Press and hold the Mode (Input 1) button.

2. While holding down the Mode button, press and hold the Auto (Input 3) button.

3. Release the Mode and Auto buttons simultaneously. The Auto Switch Active LED lights.

Selecting Normal Mode

To turn off auto-input switching:

1. Press and hold the Mode (Input 1) button.

2. While holding down the Mode button, press and hold the Normal (Input 2) button.

3. Release the Mode and Auto buttons simultaneously. The Auto Switch Active LED turns

off.

Application Diagram

The illustration below shows an example of how the SW4 3G HD-SDI switcher can be connected.

MODE

AUTO

MODE

NORMAL

AUTO

SWITCH

ACTIVE

Figure 2. SW4 3G HD-SDI Application Example

68-1571-50

Rev A

04 10

100-240V 0.2A

50-60Hz

INPUTS

1212

OUTPUTS

RS-232

SW4 3G HD-SDI

OFF

DISPLAY

MUTE

SCREEN

DOWN

VCR

DVD

DOC

CAM

LAPTOP

100

LINK

ACT

COM IR INPUT RELAY

TX RX

IPL 250

HD-SDI

Monitor

Extron

SW4 3G HD-SDI

Multi-Rate SDI Switcher

HD-SDI Projector

HD-SDI Cameras

HD-SDI VTR

RS-232

TCP/IP

TouchLink™

Control

System

SW4 3G HD-SDI 101 Setup Guide (Continued)

Andere Handbücher für SW4 3G HD-SDI

Andere Extron electronics Schalten Handbücher

Extron electronics

Extron electronics SW HD 4K PLUS Series Bedienungsanleitung

Extron electronics

Extron electronics TPS150 Bedienungsanleitung

Extron electronics

Extron electronics SW HD 4K Series Bedienungsanleitung

Extron electronics

Extron electronics YCS SW2 A Bedienungsanleitung

Extron electronics

Extron electronics RGB 580xi CCSI AAP Bedienungsanleitung

Extron electronics

Extron electronics XTP T USW 103 Bedienungsanleitung

Extron electronics

Extron electronics MMX 42 Series Bedienungsanleitung

Extron electronics

Extron electronics MPX 866 A Bedienungsanleitung

Extron electronics

Extron electronics TeamWork 601 Bedienungsanleitung

Extron electronics

Extron electronics System 4LQ xi Bedienungsanleitung

Extron electronics

Extron electronics MPS 601 Bedienungsanleitung

Extron electronics

Extron electronics 650 UT Bedienungsanleitung

Extron electronics

Extron electronics SW2 VGArs Bedienungsanleitung

Extron electronics

Extron electronics SW2 HDMI Bedienungsanleitung

Extron electronics

Extron electronics SW2 DP Bedienungsanleitung

Extron electronics

Extron electronics SW6 VGA Ars Bedienungsanleitung

Extron electronics

Extron electronics System 8 Plus Bedienungsanleitung

Extron electronics

Extron electronics System 5cr Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T 212 Bedienungsanleitung

Extron electronics

Extron electronics System 5 IP Series Bedienungsanleitung

Extron electronics

Extron electronics VSW 2VGA A Bedienungsanleitung

Extron electronics

Extron electronics MPS 602 Bedienungsanleitung

Extron electronics

Extron electronics SW2 USB Bedienungsanleitung

Extron electronics

Extron electronics SW HDMI Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung