EZPull Trap Bedienungsanleitung

For TRBP-02 (HW 2.5.0)

EZPull Trap is a voice activated, wireless clay target release

system for Trap.

EZPull Trap has special Setup and Pairing modes intended only

for the Gun Club’s administrator.

Warning: Always stand clear of any traps that may be activated

by EZPull.

1. Using Setup Mode: The Setup mode provides access to

parameters that determine the operation of the device.

1.1. Enter Setup Mode: Remove the rubber boot. Remove

the battery door. Remove one battery. Press and hold

setup “wrench” [ ] key and replace the battery. When

both lights are on steady, release the key. The lights

will alternate slowly indicating the unit is in Setup mode.

1.2. Exit Setup Mode: When in Setup mode, press and hold

the “Target” [] and “Speaker” [ ] keys

simultaneously. Both lights will turn on steady. Release

the keys. Unit will go directly to release mode ready to

release targets on key press/Voice.

1.3. Access Setup Adjustment: pressing and holding any two

key combinations simultaneously, (except [] + [ ])

will result in both lights flashing rapidly. Keep holding

the keys until both lights are turned off. Then release

the keys. The setup parameter’s current numeric value

will be indicated by the LEDs.

1.4. Understanding the numbering indicators:

1.4.1. Each parameter can be set to numbers in the

range 1 to a maximum value specific to the

parameter but never more than 16.

1.4.2. The left LED indicates the “tens” digit.

1.4.3. The right LED blinks the number of times

corresponding to the “ones” digit

1.4.4. Examples:

Number 06: left light is off; right light blinks 6

times.

Number 14: left light is on; right light blinks 4

times.

1.5. Adjusting the Number:

1.5.1. Increase: for the next value, press and quickly

release the “Speaker” [ ] key. The operation is

cyclical, after you reach the maximum value, the

next number is #1.

1.5.2. Decrease: for the previous value, press and

quickly release the “Target” [] key. The

operation is cyclical, after you reach #1, the next

number is the maximum value.

1.5.3. Verify: After each key press, observe the lights

to verify the number.

1.6. Exit adjustment: Once you verify the correct value,

press the “ON/OFF” [ ] key to save and return to Setup

mode or press the “wrench” [ ] key to exit without

saving any changes.

For TRBP-02 (HW 2.5.0)

2. Wireless Address Setup: The remote microphone units and

base station on each Trap field must be set on the same

unique address code. The address code is made of two

numbers:

Field: The Field number is a common radio address for all the

EZPull systems on the same area. If you have 16 Trap fields

or less you do not need to change this address.

Station: The station number is the unique radio address for

communicating between all units and base station on the

same trap field.

First set the same address on all the EZPull remote units on

the Trap field and then pair with a Base Station (See below).

2.1. Follow section 1 above to enter and work in Setup

mode.

2.2. Changing the Station Number: Use the [ ] + [ ]keys

combination access the Station Number adjustment.

EZPull can be set to any station number in the range 1

to 16.

2.3. Changing the Field Number: Use the [ ] + [ ] keys

combination to access the Field Number adjustment.

EZPull can be set to any Field number in the range 1 to

14.

3. Changing the Voice sensitivity: This parameter allows

adjustment of the sensitivity to voice. Higher numbers are

more sensitive. A typical value is in the range 3 to 4.

3.1. Follow section 1 above to enter and work in Setup

mode.

3.2. Use the [ ] + [ ] keys combination to access the voice

sensitivity adjustment. Voice Sensitivity values are

Typically:

3.2.1. For very high sensitivity, set to values 4 or 5.

The down side is the unit will also be sensitive to

noise and may throw targets on any speech

sound and some gunshot echoes.

3.2.2. For average sensitivity, set to 3. This will reduce

sensitivity to noise. This is the recommended

value for use with TargetManager.

3.2.3. Set to 1-2 in very noisy environment including

gunshots echoes from nearby fields. Shooter will

need to call loud and long “Pull”.

For TRBP-02 (HW 2.5.0)

4. Paring the remote units with a Base Station: The remote

units communicate with a base station that controls the Trap

machine. There are two options for a base station:

EZPull Target Manager: uses a card payment system. The

Card unit is typically mounted at the entrance to the Trap

field. Refer to the Administrator’s Guide of the EZPull Target

Manager for specific setup instructions.

Trap base station: located at the back of the trap house and

directly controls the trap machine. The remote units and base

station on each trap field must be set on the same unique

address code.

Follow procedure below to pair the base station with the

Remote units:

4.1. Turn off all the remote units.

4.2. Disconnect the Base unit from the Trap or any high

voltage source.

Warning: working while high voltage source is

connected, can be hazardous and may result in serious

injury.

4.3. Set the Base Station in paring mode.

4.3.1. Place a small magnet next to the magnetic

switch (looks like a red bar) on the left side of

the base station.

4.4. The Red LED will blink for 2 seconds, then the Yellow

LED will blink rapidly and then both lights will glow

steady. Remove the magnet at once. Both Red and

Green/Yellow LEDs will flash indicating the base station

is waiting for a Pairing call from the remote.

4.5. Set one of the remote units in Paring Mode:

Remove the rubber boot. Remove the battery door.

Remove one battery.

Press and hold the On/Off key [ ] and replace the

battery. Both lights should be on steady. Release the

key. Observe the LED indicators on the base station and

release the key.

4.6. If Pairing is successful you will see the following light

flashing sequence: Blue, Red, Blue, Yellow followed by

slow flashing of the Yellow LED indicating normal

operation mode.

4.7. Following a successful pairing, the remote unit should

be in sleep mode (no lights). If lights are still flashing,

remove one battery, wait 10 seconds and replace it.

4.8. Verify pairing: Press and release the [] on the remote.

Observe the lights on the base station. Press and

release the “Target” [ ] key. The Blue light on the base

station should turn on momentarily.

Yellow

Blue

Red

Reed Switch

Andere EZPull Fernbedienung Handbücher

EZPull

EZPull Trap Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung