EZway Comfortline II Technische Daten

Form 2-201

Rev. 7/30/18

EZ Way Comfortline II

The Wellness Bath

Operator’s Instructions

EZ Way, Inc.

PO Box 89

Clarinda, IA 51632

1-800-627-8940

www.ezlifts.com

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Users should read this manual carefully before operating the EZ Comfortline II. This bathing system is intended

for professional use only where the patient will be under the supervision of trained personnel. The system is

designed for years of trouble-free operation, with proper use and maintenance.

Operating instructions and recommended maintenance procedures are explained in the following pages.

If you have any questions regarding the operation or maintenance of your bathing system and cannot ﬁnd the

answer in this manual, please contact EZ Way at 1-800-627-8940.

Bathtub and shower water must be run at least every three days.

The height-adjustable EZ Comfortline II is designed for bathrooms in nursing homes, clinics and hospitals and

consists of:

1. The tub, side covers and maintenance hatch made of ﬁberglass reinforced polyester cover the whole

supporting frame and the actuators, control unit and all internal sanitary installations. The ½ inch cold and

hot water inlet hoses are located in the back. The maintenance hatch at the back can be removed for repair

and maintenance work.

2. The HiLo bathtub can be adjusted between 650 and 1000 mm / 26” and 40” .

3. The three-step adjustable foot support is pushed into the slots to accommodate the different lengths of

patients, to prevent them from sliding, and to provide secure support for their feet. The foot support can be

removed, for example, when using a stretcher.

4. Two built-in handles offer additional support when getting in and out of the tub.

5. Overﬂow protection and pop-up drain which opens and closes the drainage system by rotating the overﬂow

valve.

6. The thermostatic mixer is designed to regulate the water temperature to the bathtub ﬁlling spout and to the

hand-held shower. See separate thermostatic mixer operation manual for further information.

7. The shower handle with shower hose is to be used to shower the patient and to rinse equipment after

cleaning.

8. Two synchronized actuators with double controls for height adjustment to inﬁnite positions.

9. Two legs including adjustable feet in the event the ﬂoor is uneven.

10. The hand control with spiral cord is located on the hatch bracket and is used to raise and lower the tub.

Safety Notes

This HiLo bathtub may only be operated by qualiﬁed and trained staff.

Please make sure that all safety and operating instructions are read and understood and that they are adhered to

when using the bath.

The bathtub may only be installed and connected according to our assembly and installation instructions

by specialists such as a certiﬁed electrical installation company. Local guidelines and regulations as well as

installation rules for water and power connections must be adhered to.

The cold and hot water supply and the electrical wiring is the buyer’s responsibility. Electrical wiring must be

carried out on-site by a qualiﬁed electrician.

The bathtub may only be connected to the power supply via a cord that is connected to a GFCI (ground fault

circuit interrupter) including an easily accessible switch near the bathtub.

Maintenance work must be carried out by trained staff. Repairs can only be carried out after consulting the

supplier. Repairs shall only be carried out by qualiﬁed personnel using original spare parts.

Prior to using the bathtub, please make sure that there are no visible damages/defects such as:

• Cracks in the tub body/side covers

• Damages to the mains cord

• Ensure that the bathtub is lowered/raised evenly

• The handles are fastened

• It stands stable

• There are no defects and the thermostat and buttons are all working properly

The warranty and liability expire automatically if modiﬁcations or repairs are carried out or if components are

exchanged or opened without EZ Way’s consent.

If you have a question regarding the operation or maintenance of your EZ Comfortline II and cannot ﬁnd the

answer in this manual, please contact us at 1-800-627-8940.

• When using the EZ Mobile Bathing Lift System, the patient must be seated comfortably on chair and/or

stretcher, with SAFETY BELTS SECURELY ATTACHED. Safety belts must be maintained in good condition.

• Raise Stretcher/Chair to ensure clearance of all body parts over the tub. This to avoid the patient from being

pinched between the tub rim and the Chair/Stretcher frame during transfer.

• Before raising or lowering the tub, make sure that the patient’s hands ﬁrmly grasp the stabilizing bar or that the

patients arms are crossed over his/her body. This to avoid pinched arms or ﬁngers between the Stretcher/Chair

frame and the tub rim.

• Wipe beneath Stretcher/Chair to prevent water from dripping on the ﬂoor.

• Always physically check water temperature before and during bathing/ showering to ensure that the

thermoscopic mixer is functioning.

• Make sure that all parts that come in contact with the patient are intact and without sharp edges.

• Check that hoses, tub controls, connections and mixer are free from damage.

Never leave a patient unattended.

WARNING:

Always disconnect electric power before

attempting any service or repair.

WARNING:

Features and Controls

Comfortline II

Position Description

1. Tub side covers

2. Tub

3. Legs

4. Adjustable feet

5. Lifting mechanism (actuators)

6. Light/Music controls

7. Handles

8. Foot support slots

9. Drain plug

10. Thermostat with bathtub ﬁlling spout

and shower

11. Shower handle

12. Hand control UP/DOWN

13. Overﬂow drainage and control to open

and close drain plug (#8)

14. Drainage hose

Down

Figure 2 - Features and Controls Diagram

Figure 1 - Manual Up/Down Control

10 11 12

Initialization

An initialization should be carried out the very ﬁrst

time the bathtub is started up and after every power

failure.

Should be performed after/when:

• First time start-up

• Power failure (power cut, disconnection from

supply or shutdown)

Reason:

The initialization function (continuous movement

monitoring) is designed with safety and the

protection of the equipment/user in mind. The

control switches off automatically if one of the

actuators is working faster than the other one.

Process (Using Hand Control with Black

Buttons):

Please press the DOWN key on the hand control

to initialize the control mechanism. When you

reach the lowest position, keep the DOWN button

pressed for another 5 seconds. An audible tone will

sound and the system is ready to be used.

Please do not hesitate do contact us if you have any

further queries.

Instruction Manual

Using the Bath

Lower the bath to its lowest position to calibrate the

actuators.

The drain plug closes (and opens) by turning the

overﬂow valve.

Adjust the thermostat to the required temperature

(see separate thermostatic mixer operating

manual). Open the thermostat and test the water

temperature by hand or with a bath thermometer.

Fill the bath to the required level and close the

thermostat.

Always check the water temperature by hand or a

bath thermometer before the patient gets into the

bath.

Lower the tub to the lowest position with the hand

control allowing patient to step into the bath with

assistance. Place the hand control back into its

bracket at the back of the tub after use. The built-

in handles provide the patient with extra support.

When the patient is assisted into the bath with a

lift system, the lifter must be positioned close to

the side of the bathtub. The bathtub should be

in a covenient working height and be adjusted by

pressing the relevant button on the hand control.

Place the hand control back into its bracket at the

back of the tub after use.

Please make sure that the bathtub is lowered and

raised evenly, both at the head and foot end of the

tub. The tub must be level at all times. The patient

must not use the bath if it is not level.

The foot support shall be removed before the lift

stretcher is lowered into the water. It can be placed

into the required position when a chair lift is used.

The shower handle is used to shower the patient and

to rinse equipment after cleaning. Pull the diverter

knob on the thermostat. This diverts the water from

the bath ﬁlling spout to the shower handle. Always

test the water temperature by hand to prevent

patients from being scalded or shocked by cold/hot

water.

After bathing, please proceed in reverse order.

Bathtub Cleaning

Important: Never to be used on patients. Only on

equipment.

The cleaning detergent is mixed with cold water to

minimize inhalation.

Detergent is automatically mixed with the water, in

a pre-set concentration of approximately 2%.

Use only liquid, non-abrasive, non-scouring,

commercially available detergents to clean the

bathtub, the controls and the foot support. Apply

the detergent according to the detergent supplier’s

instructions.

Fittings

Plated, as well as color-coated surfaces, can be

damaged by acidic and abrasive detergent and

scouring pads. We recommend using clear water and

a soft cloth. If the ﬁttings are heavily soiled, clean

with soapy water or vinegar and rinse with clear

water and rub dry.

Please note: The user/operator is responsible for

selecting the detergents and bath additives. Please

read the detergent supplier’s instruction manual and

ﬁnd out whether the product is suitable.

Fill the Container

Remove the container lid (1) and pour the

detergent into the opening using a funnel

(MAXIMUM 1.5 LITERS / 1/3 GALLON).

Replace the lid after the container has been ﬁlled.

The detergent device is now ready for use.

Cleaning

You may use your usual detergent to clean the

bathtub. Please make sure you have read the

detergent supplier’s instructions.

Daily Use of the Cleaning System

1. Remove the cleaning spray handle (2) from

bracket (3). Hold the handle over the bathtub

while opening the shutoff safety valve (4) with

the special key.

2. Brieﬂy spray the cleaning mixture into the tub

while checking the color, smell and the foam of

the mixture. Spray over all interior surfaces of

the tub. Remove residue and debris with cloth

or brush.

3. To clean EZ Way’s Mobile Bath Lift System

Chair or Stretcher attachment, position it over

the tub and spray it with cleaning mixture. The

chair and stretcher have removable pads and the

stretcher has a head pillow which can be placed

in the tub for cleaning.

4. After cleaning, rinse with fresh water using the

shower handle.

Please note: It will take a little longer for the

detergent to be dispersed if it is the ﬁrst time the

bathtub is started up or if the container has just

been ﬁlled.

CAUTION: ALWAYS READ AND APPLY

THE DETERGENT SUPPLIER’S SAFETY

INSTRUCTIONS.

Warning: Avoid skin or eye contact

with cleaning/detergent, which can be

highly corrosive. If contact is made,

rinse immediately with excess water.

If irritation occurs, consult a doctor.

Always read and follow detergent

supplier directions carefully.

WARNING:

Figure 3 - Cleaning System

AIR SPA System - Esprit 500 (Option)

NOTE: The operating time is restricted for safety

reasons. The system (air system) switches off

automatically after 30 minutes.

Stand-By LED

The light emitting diode (0.1) is always illuminated

when the man switch is activated.

AIR SPA System

Use button 1 “ON/OFF” to turn the SYSTEM ON

(LED 1.1 is illuminated) and OFF. The AIR SPA

system starts at a medium performance level.

The level can be set as follows:

• Pressing button 2 “+” (plus) increases intensity,

LED 2.1 is illuminated.

• Pressing button 3 “-” (minus) reduces intensity,

LED 3.1 is illuminated.

• Pressing 2 “+” and 3 “-” (plus+minus) at the same

time starts an interval functions. The whirlpool is

set from maximum to minimum every 20 seconds.

Pressing those buttons again turns the interval

function off again.

An afterblow system deﬂation starts automatically

after:

• 30 minutes of continual use of the system

• 20 minutes when the system has been turned off

within the 30 minute period

The afterblow lasts approximately 30 seconds, starts

at minimum capacity and is then turned up to

maximum. The LED 1.1 is ﬂashing during waiting

time.

LED Color Light System (Option)

Use

The light system touch control is located either at

the head end (on the side of the tub covers) or at

the foot end (on the edge of the tub, depending on

bathtub model).

1. The light system is turned ON and OFF by

pressing the power switch button (1). Diode

signals that the system is in operation.

2. The light-system option allows the user to

choose a particular color, which will illuminate

the water via built-in ﬂoodlight until the system

is turned off again. An individual color can be

selected by pressing button (2).

3. The interval mode of the light system enables

the user to activate the colors of the system in

automatic intervals. All the colors of the light

system are displayed individually. The interval

mode is activated by pressing button (3).

MP3-Sound-System (Option)

Use

The sound system touch control is located either at

the head end (on the side of the tub covers) or at

the foot end (on the edge of the tub, depending on

bathtub model).

Figure 4 - Esprit 500 Controls

Figure 5 - LED Controls

Figure 6 - MP3 Operating Controls

Operating Instructions

• To start the music, press button (1). Press button

(2) if you want to turn the music off.

• The volume can be turned up and down with the

buttons (3) and (4). Press and hold button (3) for

a few seconds to increase the volume and button

(4) to decrease it.

• Switch between tracks by brieﬂy pressing button

(3 - next track) and (4 - previous track).

General Information

The control box for the MP3 sound system is

attached at the bottom of the tub. MMC-, as well as

SD memory cards up to 1 GB can be used. (Please

adhere to the general copyright regulations of the

music played).

NOTE: - ALWAYS SWITCH OFF THE MAINS

BEFORE CHANGING THE SD CARD.

To change/remove the SD memory card, move the

bathtub into its highest position for better access

to the control box. The memory card can be pulled

from the card slot (1) after the control box lid

has been removed. Now you can save the music

you would like to listen to onto the memory card

(observe copyright).

The memory card supplied contains a control

ﬁle CONFIG.TXT. This ﬁle must not be deleted

because it is necessary for the MP3 player to

function properly.

The music saved on the card must be in MP3 format

and must not be saved in sub-folders/directories

because the player will not recognize them and will

therefore not play them. After saving the music

onto the memory card, place it back into the card

slot (1) and put the lid to the control box back on.

The MP3 sound system is ready for use after the

bathtub mains has been switched on again.

Autoﬁll (Option)

The Autoﬁll allows staff to transfer and prepare the

patient for bathing while the tub is pre-ﬁlled.

General Information

The touch control for the Autoﬁll is located on rear

rim.

Operation/Handling

(1) Bath ﬁlling

(2) Handshower

Bath ﬁlling:

• Press the bath ﬁlling symbol (1) and set the

thermostat to required temperature. Test the

water temperature with your hand or with a bath

thermometer.

• The solenoid valves open and the tub will be

preﬁlled with water up to the lower level sensor.

In the meantime, the patient can be transferred

to the bath. The bath is now ready for the patient

to be positioned in the tub. When the patient

wants or requires more bathing water, press the

bath ﬁlling symbol (1) once more. The ﬁlling will

stop when the water level reaches the second level

sensor (just below overﬂow drainage).

• The Autoﬁlling can be stopped at any time by

pressing the bath ﬁlling symbol (1).

Handshower:

• Press the handshower symbol (2).

• Water will run from mixer faucet into tub. Pull

the diverter knob on faucet to activate the

handshower. To turn off the shower, press the

handshower symbol (2).

Note:

• Always use symbol 1 for tub ﬁlling and symbol 2

for shower.

• Always check the water temperature with a

thermometer or physically by hand.

• Never leave the patient unattended during the

entire bathing cycle.

Figure 7 - MP3 Memory Card

Figure 8 - Autoﬁll Controls

Routine Maintenance

Before Each Use

• Visual inspection - make sure that all electrical cords are in good condition and hoses do not leak.

• Make sure it stands securely on the ﬂoor.

• Check the temperature setting by hand or with a bath thermometer.

Daily Maintenance

• Clean the tub after every use.

• Check the cleaning supply at least daily, depending on the frequency of use.

• Avoid abrasive cleaners which may scratch the gel coat ﬁnish of the ﬁberglass bathtub and the panel.

• When the tub is not in use, lower it to its lowest position and make sure all valves are closed.

• Clean the strainers on the patient and cleaning shower handles by rubbing it with your thumb.

• Visually inspect the tub interior to make sure there are no nicks or cracks which may scratch the patient.

Monthly (On-Site Engineer or Trained Staff)

• Make sure the connecting hot/cold water hoses are ﬁtted correctly and do not leak.

• Check all screws and bolts.

• Check the power connection cord for damages (current & potential equalization).

Annually

• Maintenance and inspection by QUALIFIED STAFF.

• Movable components have to be maintained and inspected regularly because they are classiﬁed as wear parts

(e.g. motor, ﬁttings, hoses, connections, pipe interrupters).

• Inspection of electrical installation and equipment according to local requirements should be carried out

annually.

Every 5 Years

• Exchange/replace all connecting hot/cold water hoses.

After Approximately 12 Years

• EZ Way recommends that both actuators and control system are replaced.

Maintenance and/or repairs may only be carried out by qualiﬁed staff. Improper maintenance and/or repair will

void the warranty.

Please note: Iodine, bromine, and methylene blue can discolor the ﬁberglass.

The recommended frequency of these maintenance procedures will depend on the hardness of your water supply

and how often the equipment is used. It is good practice to establish these routine procedures on a weekly basis

and then adjust the frequency as your conditions indicate.

All mechanical parts inside the bathtub panel are maintenance free.

The equipment must not be used in

any way that varies from the safety

precautions and operating procedures

detailed in this manual.

WARNING:

The equipment must not be operated

until the user has read and understands

the operating manual.

WARNING:

Installation Instructions

The HiLo Bathtub Comfortline II is delivered to you fully assembled, ready to be connected to the water and

power supply at the customer’s premises and should be installed according to local guidelines and regulations.

Assembly Process

DO NOT DRAG NOR PUSH THE BATHTUB ACROSS THE FLOOR AS THIS COULD CAUSE

DAMAGE TO THE LEGS OR ACTUATORS.

When lifted, do so brieﬂy and use at least two persons.

1. Once the bathtub is in its ﬁnal position, lift brieﬂy at each end again to release any tensions that might have

been created between the feet during installation.

2. The adjustable feet are used to level/adjust the bathtub. Please bear in mind that the head end of the bathtub

has to be approximately 2 cm / 3/4” higher than the foot end to allow the water to drain more easily.

3. Please ﬂush the pipework before connecting the Comfortline to protect the bathtub ﬁttings from dirt.

4. A CERTFIED ELECTRICIAN SHALL CONNECT THE MAINS CORD TO A WALL-MOUNTED

OUTLET (SPLASHPROOF) in accordance with local regulations.

5. Use the ﬂexible drain hose to establish a connection between the drain siphon (at the bottom of the tub)

and the ﬂoor gully. This connection is best attached when the bathtub is raised into its highest position.

6. Carry out functional test.

• Test the Up/Down function by pushing each button on the hand control. INITIALIZIATION must be carried

out if the tub does not raise evenly (see separate instruction in the manual).

• Check that the thermostat is working properly and test the water temperature. If the temperature is not the

same as the actual water temperature, adjust according to manufacturer’s instructions (see separate thermostatic

mixer operating manual).

• Check that the bath tap and the shower work properly.

• Check the cold/hot water connections and make sure the drain hose is inctact.

• Make sure the mains cord is attached correctly and that it is not damaged.

The bathtub may only be used after it has been successfully and correctly installed.

On-Site Preparations

1. ½ inch hot and cold water connection, stopcock with a ¾ inch external thread for connecting nut (on-site

pre-shutoff device), incoming water pressure 1-5 bar.

2. Mains connection 230V / 50Hz, 10A, or 110V / 60 Hz depending on model. Please note: All electrical

conduit, ﬁtting and wiring to bath supplied and installed by a certiﬁed electrician in accordance with local

or applicable electric code as a minimum requirement. Main switch with signal lamp, main fuse and earth

circuit breaker are not included and must be supplied by others.

Installation of Thermostatic Mixer

1. Rinse pipes according to DIN 19881.

2. Attach connections to the water supply.

3. The hot water supply has to be the left and the cold water supply on the right side. Check the connections

for any leaks and make sure the ﬁttings are working properly.

Inhaltsverzeichnis

Andere eZway Badewanne Handbücher

eZway

eZway EZ 900HC Technische Daten

Beliebte Badewanne Handbücher anderer Marken

Agua

Agua BARTOLI-66 Bedienungsanleitung

PAA

PAA PRELUDE Bedienungsanleitung

BETTE

BETTE SILHOUETTE Bedienungsanleitung

Kohler

Kohler K-820-GC Kurzanleitung

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Bedienungsanleitung

Oliveri

Oliveri Naples Bedienungsanleitung

Lyons

Lyons Elite ETLxx663219 Series Bedienungsanleitung

Woodbridge

Woodbridge BJ500 Montageanleitung

Whirlpool

Whirlpool Ariel ARL-702 Bedienungsanleitung

TEIKO

TEIKO EXCELLENT DUO Bedienungsanleitung

American Standard

American Standard Colony 5-1/2' x 32" Bedienungsanleitung

American Standard

American Standard 3052OD.X0X Kurzanleitung

Kohler

Kohler K-1111-H2 Kurzanleitung

agape

agape MARSIGLIA AVAS1075 Bedienungsanleitung

Kohler

Kohler K-1151 Montageanleitung

Kohler

Kohler K-1158 Kurzanleitung

Kohler

Kohler K-1244 Montageanleitung

Kallista

Kallista P50045-G5 Montageanleitung

eZway Comfortline II Technische Daten

Beliebte Badewanne Handbücher anderer Marken