FAAC E124 Bedienungsanleitung
Pre-installation Checks
Please ensure that the correct cabling has been installed prior to commissioning of the system, as
incorrect cabling can prevent the unit from operating correctly immediately or after installation.
BUS-2EASY ENCODER and PHOTOCELLS Cable Specification: 2 core 0.5mm2 Multi-Strand Shielded Cable
with the Sheath connected to the Earth at one end. Please do not share BUS-2EASY devices with other DC
Voltage devices as it leads to electrical noise causing interference with the digital data on BUS-2EASY.
Motor Cable Specification: Minimum 2 core 2.5mm2 Multi-Strand Cable for a recommended distance of
10mtrs, further distances are possible but will require thicker cable.
Key Components of E124 Board
Description of Key Components
LCD
SIGNALS AND PROGRAMMING DISPLAY
DL8
“FCA2” STATUS LED
-
LIMIT SWITCH OPEN
–
IF GATE CLOSED ON
SW4
“+” PROGRAMMING BUTTON
DL9
“FCC2” STATUS LED
-
LIMIT SWITCH CLOSED
–
IF GATE
CLOSED OFF
SW5
“
-
” PROGRAMMING BUTTON
DL12
LED FOR BUS
-
2EASY DEVICE ACTIVE
SW6
“F” PROGRAMMING BUTTON
DL13
LED FOR BUS
-
2EASY DIAGNOSTICS
SW7
“RESET SW” SOFTWARE RESET BUTTON
DL1
4
LED
SIGNALING PRIMARY POWER ON
DL1
“IN1” STATUS LED
–
DEFAULT OPEN A
-
NORMAL STATE OFF
DL19
LED FOR WHEN “SW7” IS PRESSED
DL2
“IN2” STATUS LED
–
DEFAULT OPEN B
-
NORMAL STATE OFF
DL20
LED SIGNALLING “ALARM”
DL3
“IN3” STATUS LED
–
DEFAULT STOP
-
NORMAL STATE ON
J3
CONNECTOR FOR CONNECTION OF BUS
-
2EASY DEVICES
DL4
“IN4” STA
TUS LED
–
DEFAULT FSW OP
-
NORMAL STATE ON
J4
CONNECTOR FOR TERMINAL BOARD INPUTS
DL5
“IN5” STATUS LED
–
DEFAULT FSW CL
-
NORMAL STATE ON
J5
CONNECTOR FOR OUTPUT 2 (OUT2)
DL6
“FCA1” STATUS LED
-
LIMIT SWITCH OPEN
–
IF GATE CLOSED ON
J6
CONNECTOR FOR
TRAVEL LIMITS
DL7
“FCC2” STATUS LED
-
LIMIT SWITCH CLOSED
–
IF GATE CLOSED OFF
These instructions are to be considered as a rapid guide for installation and to confirm the correct
handing and polarity of the motors. They can also be used to confirm the operating logics before
additional safety devices are fitted to the system as specified by the Risk Assessment undertaken by the
installer. The installer should still familiarise themselves with the full manual and the safety information
contained within. (available at https://www.faac.co.uk/accessories-and-control-boards/control-
boards/for-swing-gates/e124-control-board)
Dip 1
Dip 2
Dip 3
Dip 4
Type
OFF
OFF
OFF
OFF
OPENING
OFF
OFF
ON
OFF
OPENING
ON
OFF
OFF
OFF
CLOSING
ON
OFF
ON
ON
CLOSING
OFF
ON
OFF
OFF
OPENING AND CLOSING
OFF
ON
OFF
ON
OPENING AND CLOSING
ON
ON
ON
ON
OPEN PULSE
If no safety devices such as traditional photocells and
Emergency Stop Button fitted, please link the terminals as
above and confirm the as shown above LED’s are lit.
The below shows a typical wiring of a set of photocells
outside across the opening (closing safety) and a set of
photocells inside beyond the arc of the gate (opening and
closing safety) and the STOP circuit linked out and confirming
t
he
as shown below
LED
’s are lit.
The following shortened table shows the programming
operations of the dip-switch inside the transmitter and the
receiver of the BUS-2EASY photocells. The full manual
contains the full list.
Leaf 1 Leaf 2 Leaf 1 Leaf 2
Leaf 1 Leaf 2
The function is
displayed only while
the button is pressed
F
or simple programming of the motor type and logic only
Basic Programming is required as below. The first
parameter that MUST be set is the “CF”. This will then allow correct configuration to proceed. Please note
that until SETUP as been completed the display will show a flashing “50”, which is SETUP requested.
Please note that if you have a mixed system i.e. A S700H/S800H and a S800H ENC or 413 and 418, this will
require the use of Easyboard software. A Windows laptop or Mac Laptop with a Type A to Type B USB lead
will be required. Available to download from https://faac.biz/documents/?drawer=Software*EasyBoard
Please note that for the majority of systems the default power and speed settings will be sufficient to allow
the first setup. These values will generally require further adjustments if force limitation is being used as part
of the safety systems and a new setup should be run after the power settings are changed.
The below in the figure is what should be seen as an example for a double gate that is using encoders.
The above is
the Status references is what will be seen under normal operation, even if the alarm LED is
illuminated. To identify the error the signalling Errors and Alarms procedure should be followed.
The following shows the typical wiring of a Maglock using either OUT 1 or OUT 2
with a relay and separate power
supply
, which are configurable in the Advanced Programming
by holding “F” and “+” together.
The following parameters from Advanced Programming may also
need to be changed if the SETUP continues to fail.
Andere Handbücher für E124
5
Inhaltsverzeichnis
Andere FAAC Steuereinheit Handbücher
FAAC
FAAC XR2 433 C Bedienungsanleitung
FAAC
FAAC 844 T Bedienungsanleitung
FAAC
FAAC E124 Bedienungsanleitung
FAAC
FAAC 624 BLD Bedienungsanleitung
FAAC
FAAC E604 Bedienungsanleitung
FAAC
FAAC 724 D-24V Bedienungsanleitung
FAAC
FAAC XIB Interface Bedienungsanleitung
FAAC
FAAC 531R Bedienungsanleitung
FAAC
FAAC E145 Bedienungsanleitung
FAAC
FAAC XRS485 Bedienungsanleitung
FAAC
FAAC XR4 433 C Bedienungsanleitung
FAAC
FAAC E124 Bedienungsanleitung
FAAC
FAAC 452 MPS Bedienungsanleitung
FAAC
FAAC E024S Bedienungsanleitung
FAAC
FAAC 455 D Bedienungsanleitung
FAAC
FAAC 200MPS Bedienungsanleitung
FAAC
FAAC MASTER-T Bedienungsanleitung
FAAC
FAAC E1SL Bedienungsanleitung
FAAC
FAAC 596/615 BPR Bedienungsanleitung
FAAC
FAAC 410 MPS Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
