Factron QHC18M Bedienungsanleitung
QHC18M 18Kw Heater Controller 3 channel
Standard
Quick start guide
Three phase 415v Three zone Manual operation Soft start
Quick Start for QHC18M 18Kw Heater Controller with Soft start
Service hatch
Isolation
switch 32A
O P MCBs
32A Type C
Power
control dial
with 4 settings
Power ON
indicator
Over Temp
indicators Front panel
1) Start by removing the service hatch. Remove the 4 fixing screws, 2 at the top and 2 in the corners.
There is a Din Rai revea ed once the service hatch has been removed.
2) Use the cab e grommets to bring the cab es into and out of the contro er base .
3) Connect the Mains IN as fo ows, Neutra b ue wire to termina #1 – Neutral IN, Live brown wire to
termina #2 – L1 IN, Live b ack wire to termina #3 – L2 IN, Live grey wire to termina #4 – L3 IN.
4) There are two methods on how to connect the Infrared Heaters to the contro er.
a)
Connect the heater or heaters Live to O/P1 termina #5 switched L1, the O/P has a maximum oad
capacity of 6Kw or 32amps. O/P1 can a so be referred to as Zone 1. Connect the heater Neutra s to
Neutral Out termina s #8 – 13. The heater Earth is connected to the Earth termina #14. The
remaining heaters shou d be distributed across the remaining two outputs O/P2 & O/P3. P ease
ensure that the load is balanced across the output terminals #5 – 7. Do not exceed the maximum
load capacity per output.
b)
Connect to an externa distribution box. Connect O/P1 to termina s marked 1, O/P2 to termina s marked
2 and O/P3 to termina s marked 3. Connect the Neutra OUT to the b ue termina s marked N. Connect
the Earth to the green/ye ow Earth termina s. Then connect the heaters to the other side of the
termina s to the appropriate connections. Live connections to termina s 1,2&3. Neutral connections to
b ue termina s N and Earth connections to the Earth termina s.
Important only a qualified electrician should install this device.
Page 1
QHC18M 18Kw Heater Controller Din Rail & connections
Distribution Box
P/No. QHDB-1824
Terminals 1 – O P1
Terminals 2 – O P2
Terminals 3 – O P3
Terminals N – N out
Terminals E – Earth
5) When a connections are comp ete and connected correct y, check once again that the wiring is correct
as per 3) & 4). Then rep ace the service hatch cover and tighten the fixing screws.
6) Turn ON or reconnect the Main Power to the contro er. The red neon amp on the front pane wi
i uminate to indicate that the unit is LIVE.
7) There are auxi iary devices such as mains operated PIR motion detectors & timer ( ag) switches. These
can be connected to termina s #15 – 17. Externa push button switches which are vo tage c ean or free
can be connected to termina s #18 – 20.
8) An optiona auxi iary device QHVC-S externa 3 zone variab e contro can be connected to termina s
#21 – 25. P ease contact the agent or distributor for auxi iary device instructions.
Important only a qualified electrician should install this device.
Page 2
CE RoHS Technical Data
Supply voltage : Three phase 415V AC 50 60 Hz All O P's with Soft start
Max. Load capacity: 18 Kilo Watts * (Load must be balanced across all 3 outputs max 6Kw each)
Over Temperature Protection: On each O P - Led indicators 1,2 & 3
Mains I P : Neutral (Blue) terminal #1
Live 1 (Brown) terminal #2
Live 2 (Black) terminal #3
Live 3 (Grey) terminal #4
Mains O P : Switched Live 1 (Brown) terminal #5
Soft start Switched Live 2 (Black) terminal #6
Switched Live 3 (Grey) terminal #7
Neutral return out (Blue) terminal #8-13
Earth out (Green Yellow) terminal #14
PIR I P : Live trigger input Zone 1 terminal #15
Auxiliary Live trigger input Zone 2 terminal #16
Device Live trigger input Zone 3 terminal #17
Ext. Sw. I P : Ext. SW1 Zone 1 terminal #18 a+b
Auxiliary Ext. SW2 Zone 2 terminal #19 a+b
Device Ext. SW3 Zone 3 terminal #20 a+b
QHVC-S I P : 0V terminal #21
Auxiliary Zone 1 terminal #22
Device Zone 2 terminal #23
Optional Zone 3 terminal #24
5V terminal #25
IP Rating: IP53
Dimensions : 350mm x 330mm x 150mm Note : Terminal connections are the same
Weights : QHC18M – 10 Kg for both the QHC18M
QHC24M – 12 Kg & QHC18MR controllers.
Tel. 00 353 1 8352718 Email: [email protected] dav[email protected]
Website: .factron.ie
Factron Ltd. Unit 12 Ashbourne Ind. Park, Ashbourne, A84 HY74, Co. eath , Ireland
Andere Factron Controller Handbücher
