Falcon DT2 Bedienungsanleitung

User’sManual

FalconDT2/FalconDT4

Safety Instructions

Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben.

1. Die Geräte nicht der Feuchtigkeit aussetzen.

2. Bevor Sie die Geräte ans Stromnetz anschließen, vergewissern Sie Sich, dass die

Spannung des Geräts mit der Netzspannung übereinstimmt.

3. Nehmen Sie das Gerät bei Überspannungen (Gewitter) vom Netz. Das Gerät könnte

sonst Schaden nehmen.

4. Sollte versehentlich Flüssigkeit in das Gerät gelangen, so ziehen sofort den

Netzstecker. Anderenfalls besteht die Gefahr eines lebensgefährlichen elektrischen

Schlags.

5. Wartungs- und Reparaturarbeiten dürfen aus Sicherheitsgründen nur von

autorisierten Personen durchgeführt werden.

6. Bei Wartungs- und Reparaturarbeiten müssen die Sicherheitsvorschriften der

zuständigen Berufsverbände und Behörden unbedingt eingehalten werden.

7. Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls die

zuständigen Stellen benachrichtigen. Unterlassung kann zum Verlust der

Versicherungsleistungen führen.

Falcon DT2/ Falcon DT4 User’s Manual

Safety Instructions

Please read the following instructions seriously.

1. Keep the equipment away from humidity.

2. Before you connect the equipment to the power outlet, please check the voltage of the

power source.

3. Disconnect the equipment from the voltage of the power source to prevent possible

transient over voltage damage.

4. Don’t pour any liquid to the equipment to avoid electrical shock.

5. ONLY qualified service personnel for safety reason should open equipment.

6. Don’t repair or adjust energized equipment alone under any circumstances. Someone

capable of providing first aid must always be present for your safety

7. Always obtain first aid or medical attention immediately after an injury. Never neglect

an injury, no matter how slight it seems.

CAUTION

Danger of explosion if battery is incorrectly replaced

Replace only with the equivalent type recommended by the manufacture.

Dispose of used batteries according to the manufacturer’s instructions.

Falcon DT2/ Falcon DT4 User’s Manual

1. BARCODE PRINTER................................................................... 4

1-1. Printer Accessories.........................................................................................................4

1-2. General Specifications....................................................................................................4

1-3. Communication Interface................................................................................................6

1-4. Printer Parts....................................................................................................................7

2. PRINTER INSTALLATION........................................................... 9

2-1. Label Installation.............................................................................................................9

2-2. Label Roll Core Switch..................................................................................................11

2-3. PC Connection..............................................................................................................12

2-4. Driver Installation..........................................................................................................13

3. ACCESSORY............................................................................. 14

3-1. Stripper..........................................................................................................................14

3-2. Cutter ............................................................................................................................17

4. CONTROL PANEL..................................................................... 20

4-1. LED Status....................................................................................................................20

4-2. Feed Key Introduction...................................................................................................20

4-3. Self-Test........................................................................................................................21

4-4. Auto Sensing.................................................................................................................22

4-5. Dump Mode ..................................................................................................................22

4-6. See-through Sensor on/off............................................................................................23

4-7. Error Messages.............................................................................................................24

5. MAINTENANCE AND ADJUSTMENT.......................................25

5-1. Print Head Module Installation / Removal Instruction...................................................25

5-2. Thermal Print Head Cleaning .......................................................................................27

5-3. Adjust the Cutter...........................................................................................................27

5-4. Troubleshooting............................................................................................................28

Falcon DT2/ Falcon DT4 User’s Manual

1. Barcode Printer

1-1. Printer Accessories

After unpacking, please check the accessories that come with the package, and store

appropriately.

Barcode printer

Power cord

Switching Power

USB Cable

Label

Quick Start Guide

CD (includes label editing software CLabel / Manual)

Falcon DT2 Falcon DT4

1-2. General Specifications

Model Falcon DT2 Falcon DT4

Resolution 203 dpi (8 dot/mm)

Print Mode Direct Thermal

CPU 32 Bit

Memory 4MB Flash, 8MB SDRAM 4MB Flash, 8MB SDRAM (with RTC)

Print Speed 2 IPS ~ 4 IPS

Print Length Max.1727mm (68”) Min.12.7mm(0.5”)

Print Width Max.54 mm (2.12”) Max.108mm (4.25”)

Sensor Type Adjustable Reflective sensor; Fixed transmissive, center aligned

Sensor Detection Type: Label gap and black mark sensing.

Detection: Label length auto sensing and / or program command setting

Media

Label Roll OD: Max. 127mm (5”)

Core Diameter: 1”, 1.5”

Width: 15mm (0.6 “) ~ 60mm (2.36”)

Thickness: 0.06~0.20mm

Label Roll OD: Max. 127mm (5”)

Core Diameter: 1”, 1.5”

Width: 25mm (1 “) ~ 118mm (4.65”)

Thickness: 0.06~0.20mm

Printer Language EZPL (Firmware downloadable)

Software Application: CLabel-IV(EZPL only)

DLL & Driver: Microsoft Windows NT 4.0, 2000 and XP

Resident Fonts 11 resident Windows bit mapped fonts (6,8,10,12,14,18,24,30,16X26,OCR A &

B); can be rotated in 8 orientations and expandable 8 times horizontally and

vertically. Scalable Font in 4 orientations.

Fonts Download

Windows bit mapped font: can be rotated in 8 orientations and expandable 8

times horizontally and vertically.

Asian font: can be rotated in 4 orientations and expandable 8 times horizontally

and vertically.

True Type Font: can be rotated in 4 orientations.

Falcon DT2/ Falcon DT4 User’s Manual

Image Handling Support BMP and PCX. Support ICO, WMF, JPG, EMF file through software.

Support image resize, rotating, mapping and inverse through software.

Barcodes

Code 39, Code 93, Code 128 (subset A,B,C), UCC 128, UCC/EAN-128 K-Mart,

UCC/EAN-128, UPC A / E (add on 2 & 5), I 2 of 5,I 2 of 5 with Shipping Bearer

Bars, EAN 8 / 13 (add on 2 & 5), Codebar, Post NET, EAN 128, DUN 14,

MaxiCode, HIBC, Plessey, Random weight, Telepen, FIM, China Postal Code,

RPS 128, PDF417 & Datamatrix code, QR code

Interfaces Serial port: RS-232 ( Baud rate : 4800 ~ 115200 , XON/XOFF , DSR/CTS )

USB port: V2.0

Control Panel One Tri-color LED: Power (Red, Orange and Green)

Function Key: FEED

Power Auto Switching 100/240VAC, 50/60 Hz

Environment Operation: 41°F to 104°F (5°C to 40°C)

Storage: -4°F to 122°F (-20°C to 50°C)

Humidity Operation: 30-85%, non-condensing. Free air.

Storage: 10-90%, non-condensing. Free air.

Cert. Approval CE, FCC Class A, CCC, CB, cUL, BSMI, GS

Printer Dimension

Length: 218 mm (8.58”)

Height: 172 mm (6.77”)

Width: 100 mm (3.94”)

Weight: 1.2 Kg

Length: 218 mm (8.58”)

Height: 166 mm (6.53”)

Width: 168 mm (6.61”)

Weight: 1.5 Kg

Options

Cutter Module

Stripper Module

RTC

Internal Ethernet Adapter Card

Cutter Module

Stripper Module

Internal Ethernet Adapter Card

Parallel port

Specifications are subject to change without notice.

Falcon DT2/ Falcon DT4 User’s Manual

1-3. Communication Interface

Serial Interface

Serial Default

Setting : 9600 baud rate､no parity､8 data bits､1 stop bit､XON/XOFF protocol and

RTS/CTS。

RS232 HOUSING (9-pin to 9-pin)

DB9 SOCKET DB9 PLUG

--- 1 1 +5V,max 500mA

RXD 2 2 TXD

TXD 3 3 RXD

DTR 4 4 N/C

GND 5 5 GND

DSR 6 6 RTS

RTS 7 7 CTS

CTS 8 8 RTS

RI 9 9 N/C

PC PRINTER

【

Note

】

The total current output from serial port can not exceed 500mA.

USB Interface

Connector Type : Type B

PIN NO. 1 2 3 4

FUNCTION VBUS D- D+ GND

Internal Interface

UART1 wafer Ethernet module

N.C 1 1N.C

TXD 2 2RXD

RXD 3 3TXD

CTS 4 4RTS

GND 5 5GND

RTS 6 6CTS

E_MD 7 7E_MD

RTS 8 8CTS

E_RST 99 E_RST

+5V 10 10 +5V

GND 11 11 GND

+5V 12 12 +5V

Falcon DT2/ Falcon DT4 User’s Manual

1-4. Printer Parts

1. LED Light

2. FEED Key

3. Top Cover

4. Power Switch

5. Cover Open Button

1. Print Head Lift

2. Label Roll Holder

3. Print Mechanism

4. Label Roll Core

5. Label Guide

6. Front Cover Piece

Falcon DT2/ Falcon DT4 User’s Manual

1. Platen Cover

2. Label Sensor

3. Platen Roller

1. Power Socket

2. USB Port

3. Fan-Fold Label Insert

4. Serial Port (RS-232)

1. Bottom Case Cover

2. Hang Holes

Falcon DT2/ Falcon DT4 User’s Manual

2. Printer Installation

2-1. Label Installation

1. Place the printer on a

horizontal surface and

open the Top Cover.

2. Press and release the

lock of Label Roll Core.

3. Pull up the Label Roll

Holder and lift the Label

Roll Core upward.

4. Place a new label roll

onto the Label Roll

Core.

5. Flip the Label Roll Core

downward and pull

back the Label Roll

Holder.

6. Pull and lock the Label

Roll Core to the original

position.

Falcon DT2/ Falcon DT4 User’s Manual

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Falcon Drucker Handbücher

Falcon

Falcon RJ-8000 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung