Fancom WEBLINKBOX Bedienungsanleitung

WEBLINKBOX

INSTALLATION MANUAL

INSTALLATIEHANDLEIDING

INSTALLATIONSANLEITUNG

NOTICE D’INSTALLATION

VERSION A2

GNDF

N.B.: The original, authentic version of this manual is the English version produced by

Fancom B.V. or one of its daughter companies (referred to further as Fancom). Any

modifications introduced to this manual by third parties have neither been checked nor

approved by Fancom. Modifications are taken by Fancom to include translations into

languages other than English and the insertion and/or deletion of text and/or

illustrations to/from the original contents. Fancom cannot be held liable for any

damages, injury, guarantee claims and other claims relating to this type of

modification, in as far as these modifications result in a content that differs from the

original English version of this manual produced by Fancom. For the latest information

about product installation and operation, please contact the customer service dept.

and/or the technical service dept. of the Fancom company concerned. In spite of the

care taken when compiling this manual, if you should discover any errors, please

inform Fancom B.V. in writing. Fancom B.V., PO Box 7131, 5980 AC Panningen (the

Netherlands).

Panningen (the Netherlands)

into other languages, partly or wholly, without express prior written permission from

Fancom. Fancom reserves the right to modify this manual without notice. Fancom can

give no guarantee, neither implicit nor explicit, for thismanual. All risks arefor the user.

This manual has been compiled with the utmost care. If, however, you should discover

an error, please inform Fancom B.V.

Art.Nr. 5911788

GB140401

Gndf

Table of contents

1. General introduction.........................................................................................1

1.1 Documentation with the control computer................................................1

1.2 How to use this manual............................................................................1

1.3 Fancom helpdesk.....................................................................................2

1.4 F-Central FarmManager™ .......................................................................2

2. Safety instructions and warnings....................................................................2

3. WebLinkBox......................................................................................................4

4. Basic functions .................................................................................................4

4.1 Login ........................................................................................................4

4.2 Changing your password..........................................................................5

4.3 Logout......................................................................................................5

5. Connecting the WebLinkBox...........................................................................6

5.1 Connecting the WebLinkBox directly to the PC........................................6

5.2 Including the WebLinkBox into an existing local network.........................8

5.3 Setting the local network to be able to connect via the Internet..............10

6. Adding and configuring controllers..............................................................11

7. Frequently Asked Questions .........................................................................13

7.1 How can I switch between user and installer screens?..........................13

7.2 How can I check the speed of the network card?...................................13

7.3 Is it possible to login with more than one person?..................................14

7.4 My IP-address is lost, how can I return to the factory default settings?..14

7.5 How can I check if the connetion settings are correct? ..........................14

8. Appendix 1: Overview WebLinkBox board...................................................16

9. Appendix 2: Side view WebLinkBox board...................................................17

10. Appendix: EG-declaration of compliance.....................................................18

Gndf

1. General introduction

This manual has been compiled with the utmost care. If, however, you should discover

an error, please inform Fancom B.V.

1.1 Documentation with the control computer

The documentation consists of the following manuals:

•User's manual

The user's manual is intended for the end user. This manual supplies information

about working with the WebLinkBox after installation.

•Installer's manual

The installer's manual is intended for installers. This manual supplies information

about connecting and configuring the WebLinkBox.

Always keep this manual close to the WebLinkBox.

1.2 How to use this manual

The following symbols are used in this manual:

Tips and suggestions.

Note providing recommendations and additional information.

Warning indicating damage to the product if you do not follow

procedures carefully.

Warning indicating danger to humans or animals.

Electrical shock hazard. Danger to humans and animals.

Example of a practical application of the described functionality.

Calculation example.

Describes the key combinations for arriving at a particular screen.

Decimals

The control computer and this manual use a decimal point in values. For example: a

weight is shown as 1.5 kg (not as 1,5 kg).

Gndf

1.3 Fancom helpdesk

For any questions and support, please contact the local Fancom Sales & Service

Center.

1.4 F-Central FarmManager™

Virtually all Fancom equipment can be controlled and managed from a centrallocation.

This requires the F-Central FarmManager software package and a communication

module. The screens in the control computers are also used in F-Central

FarmManager. This means you can start working immediately.

2. Safety instructions and warnings

Read the safety instructions, regulations and conditions carefully before installing

and/or using the system. Installing the device and remedying any malfunctions must

only be carried out by an authorized installer, according to the prevailing regulations.

The guarantee will not apply if this product is built into a switch box in any way other

than that indicated by Fancom.

The network module is a piece of electronic apparatus. There is alwaysa risk of

a malfunction occurring. Fancom hasmade every effort to ensure that analarm

is given in the event of an emergency. Unfortunately, a 100% guaranteed

cannot be provided as not all circumstances are under Fancom's control.

Fancom cannot be held liable for any damage caused by incorrect settings

and/or non or partial functioning of the entire installation. Ask your installer if

the alarm outputsof each control computer have been

connected to a separate

alarm circuit.

Inspect the network module regularly for any damage. Report any damage to

your installer immediately. A damaged control computer is dangerous!

Do not use running water (high pressure cleaners) to clean your control

computer. The network module is water resistant, but not waterproof! Do not

switch off the network module when houses are unoccupied; otherwise there is

the risk of condensation forming in the network module.

Gndf

When mounting the computer, the following should be observed:

Never mount the network module near water pipes, drainage pipes etc.

Never mount the network module in a place where the weather has direct

influence (not in the sun, or in places where the temperature can rise sharply,

etc.).

Never mount the network module in a humid and/or dusty room and certainly

not in the room where the animals are present.

No condensation may take place in or on the network module.

Use the holes behind the cover screws on the corners of the box to securely

fasten the network module.

Use gland nutsto connect the network module. Use the sealing plates supplied

to seal the gland nuts which are not used. Seal all gland nuts after connection

to prevent the entry of dust, aggressive gases and/or humidity.

To protect against lightning, place an over voltage protection device in the

power supply of the network module.

Take precautions against electrostatic discharge (ESD) when working on the

control computer. Ensure the workplace is clean and dry.

Use the wiring/cables indicated on the connection diagrams and follow all

instructions (see installer manual). Only apply power after the wiring has been

connected correctly. Incorrect connections can cause permanent damage.

Before a new fuse i

s placed, the cause of the defect should be remedied by an

authorized installer. Only replace a defective fuse by a fuse of the same type

(see connection diagram).

Gndf

3. WebLinkBox

The WebLinkBox is an interface between the controller and a PC. Controller data are

exchanged with the PC. The WebLinkBox can be accessed through the FarmManager

software as well as a web browser. This manual will help to work with the device

correctly. Chapter 4 explains some basic functions. The next chapters explain how to

connect the WebLinkBox correctly. To be able to work with the WebLinkBox proceed

as follows:

1. Connect the WebLinkBox directly to the PC (see page 6)

2. Include the WebLinkBox into an existing local network (see page 8)

3. Set the local network to be able to connect via the internet (see page 10)

If you have connected the WebLinkBox you can add and configure the controllers (see

page 11).

4. Basic functions

4.1 Login

To login to the WebLinkBox via a web browser perform the following steps:

1. Start a web browser on the PC.

2. Enter the IP-address of the WebLinkBox in the address bar and click Enter:

3. Login with your password. The main menu appears:

•Click a control computer name to go to the control panel of that control

computer.

•Click System Configuration to configure control computers (see page 11).

Gndf

•Click Change password to change your password (see page 5).

•Click Log out to logout (see page 5).

If a password isentered incorrectlythree timestheWebLinkBoxwill be blocked

temporarily (5 minutes). The following message will appear on the screen:

System temporarily blocked.

The standard user’s password is 0000. The standard installer's password is

1234.

If someone has already logged in the following message will appear on the

screen: Another session is currently active. It is not possible to login with

more than one person.

Please contact Fancom if you have lost your password.

4.2 Changing your password

There are two valid passwords: one for the user and one for the installer. After logging

in click Change password to enter a new password. Enter the new password twice and

click Send to confirm the password.

Both passwords must be unique and the password has a maximum of 5

characters.

To block the change password function, set dipswitch 3 to On.

4.3 Logout

When you are logged in go to the main menu and click the Logout button.

It is important to always log out!

If you forget to log out, log in will only be possible again after 5 minutes. If the

user does not request a new screen for 5 minutes, the WebLinkBox will

automatically log out. The user must now log in again.

Place dipswitch 4 to On to set automatic log out and block log in to 1 minute

instead of 5 minutes.

Gndf

5. Connecting the WebLinkBox

5.1 Connecting the WebLinkBox directly to the PC

Connect the WebLinkBox to the network card of the PC using the yellownetwork cable

(cross cable). The figure below shows the connection scheme.

Disconnect the power before installation.

Figure 1: Connection scheme to connect the WebLinkBox directly to the PC.

Creating connection settings to connect the WebLinkBox to the PC

To be able to work with the WebLinkBox you have to create a network between the

WebLinkBox and the PC. To set up a network you have to perform the following steps:

The network

card must be suitable for connection to a 10Mbit device. For more

information see page 13.

1. Start the PC and go to Start Control panel.

2. Double click Network connections.

3. Right click the LAN connection you want to use.

Gndf

4. Select Properties.

5. Select Internet Protocol TCP/IP.

6. Click Properties.

Write down the original settings. If the pc has to return to a local network

reinstate the original settings.

Inhaltsverzeichnis

Sprachen:

Andere Fancom Computerhardware Handbücher

Fancom

Fancom ISM. 12 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung