Fantech VT20M Bedienungsanleitung

VT 20M
Intermittent Fan Control Item #: 407392
Rev Date: 2020-02-10
WARNING: Ensure that power is
switched off at service panel before
commencing installation.
WARNING: Main Control Unit must
not be installed where it can be
reached from a tub or a shower. Unit
must be installed on GFCI circuit if
located in bathroom.
Electrical wiring must be done by
qualied person(s) in accordance with
all applicable codes and standards.
DESCRIPTION
The Fantech intermittent Fan Control is designed to
be used with Fantech FG, FR, FQ and PB fans only to
meet whole-house ventilation needs as prescribed by
independent residential ventilation authorities such as
HVI and ASHRAE.
The model VT20M controller enables the fan to run at a
preset speed for a preset portion of each hour, 24 hours
a day everyday.
The high speed override button enables the fan to run at
full speed for 20 minutes wheh needed, for example to
vent steam from a bathroom.
NORMAL OPERATION
Main Control unit (VT20M) features both a timer and
speed control that will activate an exhaust fan at a
certain speed for a selected period of time each hour.
To select fan speed, adjust lover slide control to desired
speed. To select fan on-time, ajust upper slide control
to time desired (5 minute intervals). For example, if the
fan-on time (upper slide adjuster) is set at one quarter
from the bottom, the fan will run for 15 minutes every
hour at the preset speed (lower slide adjuster).
For temporary full speed onperation, press the button
on the front of the control (main or auxiliray). The fan
will run at full speed for 20 minutes and the resume
its normal preset cycle. Full speed is indicated by a
blue light illuminated on the front of the control panel.
To return to the normal cycle before 20 minutes had
elapsed, press and hold the button for ve seconds.
SPECIFICATIONS
For control of 120V AC exhaust fans up to 2.5A.
Use only with 120V AC single phase electrical supply.
MAIN CONTROL UNIT
• Install in standard wall box prewired with LINE and
NEUTRAL.
• Using twist wire connectors, connect NEUTRAL to
both the WHITE wire on the main control unit and to
the NEUTRAL terminal on the remote fan.
• Connect LINE to the BLACK wire on the main control
unit.
• Connect the RED wire on the main control unit to the
LINE terminal on the remote fan. See wiring diagram
for more details.
• Screw the main control unit into the wall box so that it
is ush with the wall.
• Restore power at the service panel and push high
speed button to verify power to the remote fan.
• Adjust time and speed adjuster to deisred levels and
install the decorative wall plate.
The wall plate must be removed to make
adjustmnents to time and speed.
fantech

VT20M et VT20A
Contrôle intermittent pour ventilateur
IMPORTANT: S’assurer que
le courant électrique est
débranché au panneau de
service avant de commencer
l’installation.
AVERTISSEMENT: Ne pas
installer le contrôle principal
de l’appareil à proximité de
bain ou de la douche. L’appareil
doit être installé sur un circuit
GFCI s’il est installé dans une
salle de bain. Le branchage
électrique doit être fait par
un (des) individu(s) qualié(e)
d’après tous les codes et les
normes applicables.
DESCRIPTION
Le contrôle intermittent pour ventilateurs FG, FR, FQ et
PB seulement de Fantech a été conçu d’après les besoins
«Whole-House» prescrites par des personnes autorisées
indépendantes de la ventilation résidentielle comme HVI et
AHRAE.
Le modèle VT20M permet au ventilateur d’opérer à une
vitesse pré-déterminée à un intervalle de temps pré-
déterminé, 24 heures par jours, à tous les jours.
Le bouton haute vitesse prédominant permet au ventilateur de
fonctionner à pleine vitesse pendant 20 minutes, au besoin.
Par exemple, pour ventiler la salle de bain.
OPÉRATION NORMALE
Le contrôle principal VT20M comprend une minuterie
et un contrôle de vitesse qui démarrera un ventilateur
d’évacuation à une vitesse pré-déterminée pendant une
période de temps pré-déterminée à chaque heure. Par
exemple, si l’ajusteur de temps du ventilateur est à un
quart du bas, le ventilateur fonctionnera pendant 15
minutes à toutes les heures à la vitesse pré-déterminée
(ajusteur du bas).
Pour opération à pleine vitesse temporaire, presser
le bouton au devant du contrôle principal auxiliaire. Le
ventilateur fonctionnera à pleine vitesse pendant 20
minutes et reprendra ensuite sa vitesse normale pré-
déterminée. Une lumière bleue au devant du panneau de
contrôle indique que l’unité fonctionne à pleine vitesse.
Pour retourner au cycle normal avant que les 20
minutes soient écoulées, presser et tenir le bouton
pendant 5 secondes.
SPÉCIFICATION
Pour contrôle de ventilateur Fantech de 120V AC
jusqu’à 2,5A. Utiliser seulement avec alimentation
électrique a une phase de 120V AC.
CONTRÔLE PRINCIPAL
• Insérer dans une boîte murale standard pré-branchée
avec le terminal LIGNE et le terminal NEUTRE.
• Avec des connecteurs de ls à visser, brancher
NEUTRE au l BLANC du contrôle principal et au
terminal NEUTRE du ventilateur.
• Brancher le terminal LIGNE au l NOIR sur le contrôle
principal.
• Brancher le terminal ROUGE du contrôle principal
au terminal LIGNE du ventilateur à distance. Voir le
diagramme pour plus de détails.
• Visser le contrôle principal dans le boîte au mur pour
qu’il soit étanche avec le mur.
• Rétablir le courant au panneau électrique puis pressez
sur le bouton à haute vitesse pour vérier si le courant
se rend au ventilateur.
• Ajuster le temps et la vitesse désiré puis placer la
plaque décorative au mur.
La plaque décorative doit être enlevée pour
ajuster le temps ou la vitesse.
fantech

VT20M y VT20A
Control intermitente para ventiladores modelos
IMPORTANT: Antes de instalar este
producto, asedúrese que la corriente
de eletricidad esté apagada en el
panel de servicio.
ADVERTENCIA: Ni la Unidad de
Control Principal deberán estar
instaladas en lugares que permitan
su acceso ni desde una tina de
baño ni de una ducha. La unidad
se debe instalr en un circuto con
GFCI (interruptor de cicuito de falla
à tierra) si se encuentra cerca de
un baño, Todas la instalaciones
eléctricas deben ser efectuadas pro
electricistas calicados y de acuerdo
a todos los estándares y códigos
aplicables a la industria.
DESCRIPTIÓN
El Ventilador Control intermitent Fantech está diseñado para
usares con los ventiladores FG, FR, FQ y PB de Fantech n de
satisface la necesidades de ventilación residencial, tales como
la HVI y la ASHRAE.
El combinador modolo VT20M permit que el ventilador
foncione diariamente, 24 horas al día, a una velicidad
pre-establecida y durante une porción pre-establecida de
tiempo decada hora. El botón de alta velocidad permite que el
ventilador funcione a su máxima velicidad durante 20 minutos
cuando así se requera, como po ejamplo para ventila el vapor
que queda en el baño.
FONCIONAMIENTO NORMAL
La unidad principal de control (VT20M) tiene un
temporizador y un controlador de celocidad que activa
un ventilador de succión a une velocidad determinada
y por un período de tiempo seleccionado cada hora.
Para seleccionar la velocidad del ventilador, ajustar el
controlador deslizante superior a la velocidad deseada.
Para seleccionar el tiempo de funcionamiento del
ventilador, ajustar el controlador deslizante superio al
tiempo deseado (incrementos de 15 minutos).
Para logar una velicidad máxima temporal presione el
botón de la parte del frente del control (ya sea principal
o auxiliar). El ventilador foncinará a su velocidad
máxima durante 20 minutos y después volverá a su
ciclo previanmente seleccionado como “normale”. Una
luz azul encendida en el frente del panel de control
indica velocidad máxima. Para regresar al ciclo normal
antes de que pasen 20 minutos, presione y sosstenfa
presionado el botón por 5 segundos.
ESPECIFICACIONES
Para control Fantech de 120V AC hasta de 2.5A.
Úselo solamente con suministro de electricidad
monofásica de 120V AC.
UNIDAD PRINCIPAL DE CONTROL
IInstála en una caja de pared estándar que ya tenga
instalados la LÍNEA y el hilo NEUTROS. Utilizando
conectadores de alambre entrelazados, conecte el
NEUTREAL tanto al alambre BLANCO de la unidad
de control principal como a la terminal NEUTRAL del
ventilador a distancia. Conecte el alambre ROJO de la
unidad principal de control a la terminal de la LÍNEA del
ventilador a distancia. para moyores detalles, favor de
ver el diagrama de alambrado anexo.
Antonille la unidad principal de control hacia la caja de
pared para que quede nivelada con la pared.
Vielva a restaurar la electocidad en el panel de servicio y
oprima el botón de alta velocidad a los niveles deseados
e instale la placa de pared decorativa.
Para ajustar el tiempo y la velocidad, hay que
quitar la placa de pared decorativa.
fantech

Contacts:
United States / États-Unis / Estades Unidos Americanos
Canada / Canada / Canadá
A
A
D
C
B
C
D
D
B
A
D
C
E
H
F
G
I
Mounting Plate
Plate décorative
placa de pared decorativa
Electrical Box
Boîte électrique
Caja elétrica
Machine screw
Vis mécanique
Tornillo
Not included
Non inclus
No se incluye
Main control
Contrôle principal
Control principal
Fan
Ventilateur
Ventilador
White
Blanc
Blanco
Black
Noir
Negro
Red
Rouge
Rojo
Neutral
Neutre
Neutral
Line
Ligne
Línea
Load
Charge
Carga
A
VT20M
Wiring Diagram / Branchement électrique / Cableado
Installation / Installation / Instalación
fantech
4.0
M
0
U
I
N
T
S
I
G
H
H
2
E
E
P
D
S
E
20.0
4.0
R1.0
12.0
15.0
30.0
T
U
N
M
I
E
E
E
I
H
2
0
H
G
S
P
D
S
I
M
N
U
T
G
H
H
I
2
0
S
D
E
E
P
E
S
31.8
63.5
fantech
fantech fantech
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Fantech Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken

Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation
JS Automation MPC3034A Bedienungsanleitung

JAUDT
JAUDT SW GII 6406 Series Kurzanleitung

Spektrum
Spektrum Air Module System Bedienungsanleitung

BOC Edwards
BOC Edwards Q Series Bedienungsanleitung












