Fast Standalone XIM Bedienungsanleitung

Part #???

Revised ??????

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 366-1807

www.fuelairspark.com

Part # FAST4-160

Revised 11/30/09

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 375-3408

www.fuelairspark.com

Standalone XIM™

Thank you for choosing FAST™ products; we are proud to be your manufacturer of choice. Please read this

instruction sheet carefully before beginning installation, and also take a moment to review the included limited

warranty information.

These instructions focus on the Standalone XIM™. Please refer to the original XIM™ instructions (Part

#FAST4-101) for general XIM™ information.

Standalone Modes

The XIM™ has three modes of Standalone operation.

1. Onboard – adjustments made with physical switches mounted directly on the XIM™ circuit board.

2. Remote – adjustments made through a small, handheld device intended to be used in the cockpit.

3. PC Software – adjustments made through a software package loaded on a laptop.

Onboard Switch Settings

The XIM™ is configured through a series of DIP switch settings. The switches are located under the back cover

of XIM™. To access the switches, simply take the lid off by removing the 5 screws, being careful not to tear the

gasket beneath the lid.

Quick Start Guide for Onboard Mode

These example settings can be used to get up and running quickly. They are on the “safe” side. If desired, any of

the settings can be adjusted to suit the motor or application. More detail about each switch setting is given on the

following page.

INSTRUCTIONS

Part #???

Revised ??????

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 366-1807

www.fuelairspark.com

Part # FAST4-160

Revised 11/30/09

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 375-3408

www.fuelairspark.com

For reference, these LS1 settings will give you…

Idle timing: 20° (idle timing plus vacuum advance gives 30° at idle)

Max timing: 24°

All-in RPM: 2800 rpm

Vacuum Advance: 10° (added to base timing at low load)

Rev Limit: 6000 rpm

SW1 (long, 8 DIP switch toggles)

All modes of XIM™ operation require that these be set per application as shown below. Note that #7 needs to be

“ON” to operate in any Standalone mode.

XIM™ DIP Switches

DIP Switch (1-4)

[0=OFF, 1=ON] Ignition Strategy Crank Input “Crank Ref. Angle (*BTDC)” setting

in C-Com XFI™ software

0 - 0 - 0 - 0 Crank Trigger 1/2/3/4X, 50* BTDC 50

1 - 0 - 0 - 0 OE Crank Trigger 1/2/3/4X, 1-10* BTDC Actual Crank Position (1-10) + 45

1 - 0 - 1 - 1 Ford Mod, 2 or 4 Valve 36-1 (1 tooth cam) 60

1 - 1 - 0 - 1 Ford Mod, 3 Valve 36-1 (5 tooth cam) 60

1 - 1 - 1 - 1 Chrysler Hemi 36-2-2 50

1 - 1 - 1 - 0 Chrysler Hemi Eagle 60-2 54

0 - 0 - 1 - 1 GM Gen 3 - LS1/LS6 24X (Special) 50

0 - 1 - 1 - 1 GM Gen 4 – LS2/LS7 60-2 (4 pulse cam) 49

0 - 1 - 0 - 1 GM Gen 4 / Gen 3 Cam 60-2 (1 pulse cam) 49

1 - 0 - 0 - 1 24 Pulse Dist. Plug 24X (Even, 1 cam) 50 - 60

Part #???

Revised ??????

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 366-1807

www.fuelairspark.com

Part # FAST4-160

Revised 11/30/09

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 375-3408

www.fuelairspark.com

DIP Switch (5-6)

[0=OFF, 1=ON] # of

Cylinders DIP Switch (7)

[0=OFF, 1=ON] Operation

Mode

DIP Switch (8)

[0=OFF, 1=ON] Coil Layout

0 - 0 2 Cylinder 1 Standalone 1 Coil per Cylinder

1 - 0 4 Cylinder 0 CAN Enabled 0 Waste Spark

0 - 1 6 Cylinder

1 - 1 8 Cylinder “CAN Enabled” allows XIM™ to

communicate with XFI™ “Waste Spark” – Each coil fires two

companion cylinders simultaneously.

SW2 / SW3 / SW4 / SW5 (rotaries with detents)

SW2, SW3 and SW5 settings are only required for Onboard mode. They are not used with the optional Remote

or PC software.

Setting Resolution Min

(position 0) Max

(position 9)

SW3 Idle timing (°BTDC) 2 6 24

SW2 Max timing (°BTDC) 2 22 40

SW5 All in (RPM) 200 1800 3600

SW4* Rev Limit 1000's

(RPM) 1000

(position 3)

3000 9000

* SW4 is also used to select between the three modes of Standalone operation. It is set to 0 for PC Software

mode, 1 for Remote mode, or 3-9 for Onboard mode.

SW3 SW2 SW5 SW4*

Switch

Position Idle Timing

(°BTDC) Max timing

(°BTDC) All in

(RPM) Standalone

Mode Rev Limit

1000’s (RPM)

0 6 22 1800 PC Software n/a

1 8 24 2000 Remote n/a

2 10 26 2200 n/a n/a

3 12 28 2400 Onboard 3000

4 14 30 2600 Onboard 4000

5 16 32 2800 Onboard 5000

6 18 34 3000 Onboard 6000

7 20 36 3200 Onboard 7000

8 22 38 3400 Onboard 8000

9 24 40 3600 Onboard 9000

Timing Curve

SW2, SW3 & SW5 are used to construct a base timing curve.

RPM

SW2: Max Timing

1250

Ignition Timing

SW3: Idle Timing

SW5: All-in RPM

Part #???

Revised ??????

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 366-1807

www.fuelairspark.com

Part # FAST4-160

Revised 11/30/09

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 375-3408

www.fuelairspark.com

R18 / R19 (rotaries without detents)

R18 and R19 settings are only required for Onboard mode. They are not used with the optional Remote or PC

software. These can be set fully counter-clockwise (minimum setting), fully clockwise (maximum setting), or

any position in between.

Setting Resolution

Min

(full ccw)

(position 1)

Max

(full cw)

(position 3)

R18 Rev Limit 100’s

(RPM) n/a 0 900

R19 Vacuum advance

(°) n/a 0 20

Rev Limiter

SW4 and R18 are both used to set the rev limiter in Onboard mode. Adding the two settings together gives the

rev limit. For example…

SW4 : position 6 = 6,000 RPM

R18 : center of rotation = 450 RPM.

Together, they set the rev limit to 6,450 RPM.

Vacuum Advance

The vacuum advance feature adds an adjustable amount of timing on top of the base timing curve. The full

amount is added at lower load and phased out as load increases. The MAP sensor must be installed (harness

plugged into sensor and a vacuum line run from the sensor to the intake manifold) for this feature to work

properly. In Onboard mode, R19 can be turned fully counter-clockwise to disable the vacuum advance feature.

Status LED

The Status LED on the XIM™ will…

•Flash briefly once a second to confirm XIM™ is set for Standalone operation

•Flash an even on/off pattern when started up in flash mode (blue “Flash” wire grounded at key-on.

Used to update firmware in XIM™.)

Tach Output

Pin 30-A3 is a 12V square wave tach output. It is available as a loose Brown/white wire and at pin F of the

“CAM/HALL EFFECT” connector.

Manifold Pressure 73 kPa

Added Timing

R19: Vacuum Advance

87 kPa

Part #???

Revised ??????

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 366-1807

www.fuelairspark.com

Part # FAST4-160

Revised 11/30/09

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 375-3408

www.fuelairspark.com

Fuel Pump Relay Control

Pin 18-B3 is a fuel pump relay output. It is available as a loose Green wire. It can be wired to the negative side

of a fuel pump relay to control an electric fuel pump. (Do NOT connect it directly to a fuel pump.) The pump

will be primed at key-on. And then will run whenever the XIM™ sees an RPM signal.

Unused Connectors

When using the XIM™ in one of the Standalone modes, the “CAN LINK” and “TO XFI CAM/HALL

EFFECT” connections are not used.

XIM™ Pinout Chart

XIM™

Pin Function Wire Color XIM™

Pin Function Wire Color

30-A1 Inductive Crank Input Red 18-A1 +12V Switched Input Pink

30-A2 Discrete Crank Input Yellow 18-A2 Retard #2 Input Purple

30-A3 Crank Output / Tach Brown/White 18-A3 Digital GND Black/White

30-B1 Digital GND Black (/White) 18-B1 Battery Input Red

30-B2 Digital GND Black/White 18-B2 Retard #1 Input Gray

30-B3 Cam Output Yellow/Black 18-B3 Fuel Pump Output Lt. Green

30-C1 Inductive Cam Input Red 18-C1 Coil Output A Orange

30-C2 Discrete Cam Input Brown 18-C2 Auxiliary Output*

30-C3 Flash Enable Input Blue 18-C3 Power GND Black

30-D1 Digital GND Black (/White) 18-D1 Coil Output D Purple

30-D2 Digital GND Black/White 18-D2 Coil Output C Gray

30-D3 Load Input White/Violet 18-D3 Coil Output B Blue

30-E1 Analog 2 Input* 18-E1 Coil Output E Black

30-E2 5V Reference Red/White 18-E2 Power GND Black

30-E3 Analog GND Black/Pink 18-E3 Power GND Black

30-F1 RS-232 RxD Black 18-F1 Coil Output F Brown

30-F2 RS-232 TxD Red 18-F2 Coil Output G Yellow

30-F3 Dig GND (RS-232) White 18-F3 Coil Output H Green

30-G1 CAN_H Yellow

30-G2 CAN_L Green

30-G3 Digital GND Black/White

30-H1 EST Output A Purple

30-H2 EST Output B Purple/White

* Reserved for future use

Notes:

See letters and numbers molded into sides of

Part #???

Revised ??????

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 366-1807

www.fuelairspark.com

Part # FAST4-160

Revised 11/30/09

FAST™

3400 Democrat Rd.

Memphis, TN 38118

Phone: (901) 260-3278 Fax: (901) 375-3408

www.fuelairspark.com

30-H3 2-Step Input Orange

30-J1 EST Output C Red

30-J2 EST Output E Blue/White

30-J3 EST Output G Green/White

30-K1 EST Output D Red/White

30-K2 EST Output F Green

30-K3 EST Output H Blue

connectors to find pin locations.

“30-“ and “18-“ refer to 30 way and 18 way

connector.

Limited Warranty

FAST, Inc. warrants that all of its products are free from defects in material and workmanship for a period of 1

year from the date of purchase. This limited warranty shall cover the original purchaser.

FAST, Inc.’s obligation under this warranty is limited to the repair or replacement of its product. To make a

warranty claim, the part must be returned within 1 year of purchase to the address listed below, freight prepaid.

Items covered under warranty will be returned to you freight collect. It is the responsibility of the installer to

ensure that all of the components are correct before installation. We assume no liability for any errors made in

tolerances, component selection, or installation.

There is absolutely no warranty on the following:

•Any parts used in racing applications.

•Any product that has been physically altered, improperly installed or maintained.

•Any product used in improper applications, abused, or not used in conjunction with the proper parts.

•Damage due to excessive manifold pressure, i.e. nitrous backfires, engine misfire, etc.

There are no implied warranties of merchantability or fitness for a particular purpose. There are no

warranties, which extend beyond the description of the face hereof. FAST, Inc. will not be responsible for

incidental and consequential damages, property damage or personal injury damages to the extent permitted by

law. Where required by law, implied warranties or merchantability and fitness are limited to a term of 1 year

from the date of original purchase.

This warranty gives you specific legal rights and you may also have other legal rights, which vary from state to

state.

Inhaltsverzeichnis

Andere Fast Steuereinheit Handbücher

Fast

Fast XIM Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung