Fast WORM-DIAL Bedienungsanleitung

WITH LUX LINER

HELMET OPERATOR’S MANUAL

*Showing FAST Ballistic High Cut

with Lux Liner and Worm-Dial.

HELMET VERSIONS

FAST HELMETS

This manual is specific to the following helmet models: FAST Ballistic High Cut, and FAST Ballistic

Maritime, with pre-installed Lux Liner (H-Nape or Worm-Dial Versions).

FAST Ballistic High Cut Helmet with Worm-Dial and Lux Liner is used for reference drawings

throughout this Operator’s Manual. If there are any procedure discrepancies due to other helmet / Lux

Liner / Chinstrap versions they will be specifically noted.

PRE-INSTALLED LUX LINER KIT:

Pads are shipped in the standard configuration with nine installed pads. Pads can be placed in a variety

of alternate positions to achieve optimal comfort.

ALL HELMET VERSIONS INCLUDE:

ADDITIONAL PADS

(Also Included)

(1) Thin x2 Pad

(1) Thin x4 Pad

(1) Impact Liner

(1) H-Nape Chinstrap

(2) Thick x4 Pads

(2) Thin x2 Pads

(5) Thick x2 Pads

S/M KIT INCLUDES:

M/L &L/XL KIT INCLUDES:

(1) Impact Liner

(1) H-Nape Chinstrap

(1) Thick x5 Pad

(2) Thin x2 Pads

(5) Thick x2 Pads

(1) Thick x4 Pad

(1) Impact Liner

(1) Worm-Dial Fitband

(1) Thick x4 Pad w/ Tabs

(2) Thin x2 Pads

(5) Thick x2 Pads

(1) Thick x4 Pad

S/M KIT INCLUDES:

M/L &L/XL KIT INCLUDES:

(1) Impact Liner

(1) Worm-Dial Fitband

(1) Thick x5 Pad w/ Tabs

(2) Thin x2 Pads

(5) Thick x2 Pads

(1) Thick x4 Pad

ADDITIONAL PADS

(Also Included)

(1) Thin x2 Pad

(1) Thin x4 Pad

WORM-DIAL H-NAPE CHINSTRAP WORM-DIAL H-NAPE CHINSTRAP

FAST BALLISTIC HIGH CUT HELMET FAST BALLISTIC MARITIME HELMET

(1) WING-LOC ADAPTER (1) PICATINNY ADAPTER VAS SHROUD / SKELETON SHROUD (Optional)

7-8

9-15

16-22

TABLE OF CONTENTS

HELMET COMPONENTS

SIZING GUIDE

PRO SETUP

CHINSTRAP OPERATION

WARNING & WARRANTY

OPERATOR NOTES

MAINTENANCE SCHEDULE

REPLACEMENT KITS

REPLACEMENT WORM-DIAL FITBAND COMFORT PADS

REPLACEMENT CHINSTRAP & LUX LINER

REPLACEMENT EXTERIOR VELCRO

REPLACEMENT VAS SHROUD

REPLACEMENT FAST SIDE RAILS

ACCESSORY INTEGRATION

COUNTERWEIGHT & HELMET COVER

VAS SHROUD

FAST SIDE RAILS (ARCs)

EXTERIOR VELCRO®

SIDE COVERS & GUNSIGHT MANDIBLE

COMMs HEADSET

HELMET COMPONENTS

Integrated Retention System

(LED Version Available)

VAS Shroud

*Optional

Helmet Shell

Exterior Velcro

Ballistic Screws

& T-Nuts

Bungee FAST Side

Rail (ARC)

Note: LED = Left Eye Dominant

Lux Liner

(Showing Worm-Dial Version)

WORM-DIAL FITBAND

Impact Liner

H-NAPE CHINSTRAP

PAD CONFIGURATION:

(5) Top Pads

x4 or x5 Front Pad

(Row Quantity Depends on Lux Liner Size)

Rear Pad

Side Pad Side Pad

(5) Top Pads

x4 or x5 Front Pad

(Row Quantity Depends on Lux Liner Size)

Rear Pad

Side Pad

SIZING GUIDE

FAST helmets have been designed from the ground up to t the largest group of users in helmet sizes

that most closely match their heads. However, there is still a small percentage of users that will not

t our standard sizing congurations. Please use the sizing guide below to determine your helmet

size and your chinstrap size. If you require a non-standard chinstrap/helmet conguration, custom

solutions are available.

HELMET SIZING GUIDE

X-LARGE

FAST HELMET SIZE WORM-DIAL FITBAND SIZE (in)

S/M MEDIUM

M/L

L/XL

LARGE

27.5-30.5

26-29

24.5-27.5

CUSTOM FIT COMBINATIONS

Your FAST Helmet can be custom fit

with an alternate

chinstrap size upon

ordering or a replacement chinstrap can

be purchased separately.

CHINSTRAP SIZING GUIDE

ince people have different shaped heads, helmet size

(the size of the

top of your head) is not always proportional

to the chinstrap size (the size

of your face). H-Nape chinstrap is one size fits all.

14 1 5

16 17

18 19

2 0

RUN MEASURING

TAPE ALONG FRONT

EDGE OF EAR

FAST HELMET SIZE

Head Circumference (cm)

Head Circumference (in)

Head Size (US)

53 - 56

20⁄ - 22

S/M

up to 7

56 - 59

22 - 23¼

M/L

up to 7⁄

59 - 62

23¼ - 24⁄

L/XL

up to 7⁄

62 - 64.5

24⁄- 25⁄

XXL

up to 8⁄

S/M HELMET WITH

LARGE CHINSTRAP

L/XL HELMET WITH

MEDIUM CHINSTRAP

13 14

15 16

17 18

2 0

FAST Helmets were designed for professionals who expect the most from their equipment. Just like

fine-tuning the suspension on a racecar or sighting in a fire-arm, the helmet must be set up properly

before use to function correctly. If you do not follow these instructions, your helmet will not function in

accordance with stated performance.

PRO SETUP

HEIGHT ADJUSTMENT

•The distance from the top of the eyebrow to the bottom front of

the Lux Liner Impact Layer should be approximately 0.5”- 1”.

There should also be enough room around your ears for COMMs

hearing protection.

•If the helmet sits at an uncomfortable angle, adjust the top

pads or try using the Additional Pads provided in different

combinations (see step two “Additional Pads” for more detail)

(5) Top Pads

ADJUST THE TOP PADS

•Put the helmet on. All Lux Liner Pads come pre-installed in the helmet.

Worm-Dial Fitband Users:

Turn the Worm-Dial to loosen the Fitband so that all of the helmet weight is resting on top of

your head. With the Fitband loose, check how high / low the helmet is sitting.

•All Users: Forehead pad should be above and not resting on the bony ridge of your eyebrows.

0.5”-1”

ADDITIONAL PADS

•If the helmet feels tight or uncomfortable, adjust the Top Pads,

and swap Thick x2 Pads out for

Additional Thin x2 or x4 Pad(s) try different combinations until helmet feels comfortable.

(1) Thin x4 Pad

(1) Thin x2 Pad

H-NAPE USERS WORM-DIAL USERS

6(1) Thin x4 Pad

(1) Thin x2 Pad

WORM-DIAL FIBAND OPERATION

LOOSEN HEAD-LOC SLIDERS

•With the helmet off, loosen all (4) Head-Loc Sliders by sliding

them away from the chincup.

CONNECT CHINSTRAP BUCKLE

•Place the helmet on your head and connect the low profile

chinstrap buckle. This is easiest when placing your index fingers

behind each side of the buckle as shown.

TIGHTEN FRONT STRAPS

•With both hands, pull the two Front Head-Loc Sliders on the

webbing straps that come from the front temples of the helmet

toward your chin until snug.

ADJUST WORM DIAL

•Turn the Worm-Dial Adjustment to tighten the tband until it

is comfortably snug.

TIGHTEN BACK STRAPS

•With both hands, pull the two Rear Head-Loc®Sliders on the

lower webbing straps toward your chin until snug.

Note: The technique works best if you only hold the

plastic sliders and don’t touch the webbing.

Head-Loc

Slider

H-NAPE CHINSTRAP OPERATION

LOOSEN HEAD-LOC SLIDERS

•With the helmet off, loosen all (4) Head-Loc Sliders by sliding

them away from the chincup.

CONNECT CHINSTRAP BUCKLE

•Place the helmet on your head and connect the low profile

chinstrap buckle. This is easiest when placing your index fingers

behind each side of the buckle as shown.

TIGHTEN FRONT STRAPS

•Tighten the front straps by pulling the Head-Loc Sliders toward your chin.

This is easiest when holding either side of the slider with your thumb and

middle finger while using your index finger in the top recess.

ADJUST NAPE PAD

•Position comfortably (as low as possible) on the back of your

head. Pull Head-Loc Slider with your right hand.

TIGHTEN BACK STRAPS

•With both hands, pull the two Rear Head-Loc®Sliders on the

lower webbing straps toward your chin until snug.

Note: The technique works best if you only hold the

plastic sliders and don’t touch the webbing.

Head-Loc

Slider

NIGHT OPERATIONS AIRBORNE OPERATIONS

BREACHING / ATV

MISSION DOCUMENTATION

Bungee

IFF Strobe

Counterweight

NVGs

IR Illuminator O2 Mask

Goggles

COMMs Headset

Video

Camera Video

Camera

HMD Ballistic

Mandible

Side

Armor

Ballistic

Visor

There are three ways of attaching accessories to the FAST Helmet. The Ops-Core VAS Shroud, FAST Side

Rails (ARCs), and Exterior Velcro. These three components provide convenient and secure ways to quickly

attach and

detach various accessories to different positions, and allow for personalized customization.

RECOMMENDED CONFIGURATIONS

There are numerous accessories that can be attached to your FAST Helmet to be used in a variety of

situations. Below are some recommended congurations.

ACCESSORY INTEGRATION

VAS Shroud

FAST Side Rail (ARC)

Side Exterior

Velcro

Rear Exterior

Velcro

Top Exterior Velcro

COUNTERWEIGHT & HELMET COVER

COUNTERWEIGHT ATTACHMENT

REMOVE REAR SCREWS

Remove screws and T-nuts at back of FAST Side Rails.

Align the anchor of Counterweight to the holes on the

rear of the FAST Side Rail. The Rear Exterior Velcro will

hold Counterweight in place. Use your ngers to loosely

attach a screw to the Counterweight and FAST Helmet. Be

sure to place screw through Counterweight Anchor, Side

Rail, Helmet Shell, and Chinstrap Anchor. Repeat for the

opposite side.

SECURE COUNTERWEIGHT

Use a screwdriver to tighten all screws from the outside

of the Counterweight, making sure the Counterweight is

securely fastened to the rear of the FAST Helmet.

Note: Adding weight to helmet increases risk of

neck strain and injury. Only add counterweight

when absolutely necessary to balance loads on

front of helmet.

COUNTERWEIGHT KIT

The Counterweight Kit Includes (1) Counterweight

Pack with (5) Lead Weights and (2) 24mm Screws.

HELMET COVER

The Helmet Cover protects the shell outer

surface while still providing the functionalities

of the FAST platform.

(Open View)

(2) 24mm Screws

Lead

Weight

Window for Mini

Glow Stick

Anchor for

Side Rail

(Closed View)

FAST

Side Rail

Rear

Exterior Velcro

The Counterweight Kit reduces neck fatigue on long missions with night vision goggles or other accessories

that add weight to the front of the helmet. The Helmet Cover provides a variety of camouage options for

different environments.

Rear Pouch

Goggle

Retention

Flap

Velcro

Detachable Rear Pouch

Fits ANVIS Battery Pack

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fast Motorradzubehör Handbücher

Fast

Fast Ballistic High Cut Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

3M Speedglas 9100 MP Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

Sperian

Sperian Optrel p420 Bedienungsanleitung