Feathercraft Kurrent Bedienungsanleitung
The Legendary Performance
YOUR ADVENTURE UNFOLDS
TM
Feathercraft Products Ltd. 4-1244 Cartwright Street on Granville Island, Vancouver, British Columbia, Canada V6H 3R8
Toll Free: 1-888-681-8437 Tel: (604) 681-8437 Fax: (604) 681-7282 www.feathercraft.com info@feathercraft.com
Kurrent
FOLDING KAYAKS
Contents
Kurrent Folding Kayak...........................................................Page 2
Specifications ........................................................................Page 3
Kurrent Frame .......................................................................Page 4
Care and Maintenance ..........................................................Page 5
Kurrent Assembly Instructions ..............................................Page 8
The Feathercraft Sea Sock .....................................................Page 15
Disassembly..........................................................................Page 16
Feathercraft Kurrent 1
Built in coaming
Feathercraft Kurrent 2
Comfortable sling seat
with inflatable back
& bottom
Removeable air sponsons inside
skin along gunwales
Hull reinforced on outside over
keel and chine bars
Kurrent Folding Kayak
Feathercraft Kurrent 3
Seat: 420 denier rip-stop nylon with inflatable
air back and air bottom
Accessories: Included with every kayak:
Nylon Spray Skirt
Sea Sock
Adjustable Foot Brace Bar
Repair Kit
Pack Bag
Assembly Video
Illustrated Instructions
Specifications
Length:
Beam:
Weight:
3.98 m (13’1”)
63.5 cm (25”)
10.65 kg (23lbs)
Storage Volume: Low
Frame: 5/8” Round
6061 - T6 Aluminum
Magnesium Tubing with clear
Anodized Coating
Crossribs: Injection Molded Polycarbonate
Skin Material: Welded Urethane
Pack size: 79 x 40 x 28 cm (31 x 16 x 11”)
chines, gunwales and deckbars
through-bolted permanently
to keel plate (same for bow
and stern)
Feathercraft Kurrent 4
Kurrent Frame
crossribs are injection
molded polycarbonate
seat sling suspended
from chines & gunwales
foot brace
shockcorded tubing
Care and Maintenance
The Frame
The tubular frame is very strong and corrosion resistant. Basic
maintenance is required, generally every 2 to 3 months, after
extensive use, or if water has flooded the kayak. Disassemble
the kayak frame. Completely rinse the inside and outside of the
tubes with fresh water. Keep frame inserts and extension bars
free of sand and grit.
Using rubber gloves, coat the frame inserts and sliding sections
with Bo-Shield T-9 (a small bottle is included in the repair kit).
Made by Boeing, this is an excellent lubricant and protectant.
Apply this to the frame prior to assembly to allow tubes to
slide together more easily. This product can usually be found in
marine hardware stores and some bike shops.
Apply the lubricant liberally to all sliding pieces and spring
buttons to prevent parts from seizing, if you plan to leave the
kayak assembled for a couple of months.
After paddling, sponge out water that may have pooled along
the keel.
The Skin
The urethane skin fabric is very UV and abrasion resistant, given
normal use. Do not store outside, unprotected. The fabric can
be affected if continually stored in moist and damp conditions.
Do not store the skin rolled up wet. Care must be taken when
approaching rocks, barnacles or shells. To avoid puncturing the
hull, exit the kayak and lift over any sharp surfaces. Do not pull a
loaded boat over rocks or carry a loaded kayak.
A patch kit is included for repairs. Urethane adhesive is used to
apply any patches or fill nicks. Instructions for patching are on the
adhesive. Duct tape will also work well, and is a good addition to
your repair kit.
Feathercraft Kurrent 5
Welded Sealskin
The Polytech deck and Duratek hull are urethane. Seams are
permanently sealed.
A patch kit is provided for deck, hull or sponson punctures.
The urethane glue will work for repairs to all of these fabrics.
For preparation and application, follow the instructions on the
adhesive container.
Sponsons
Due to the tight fit of the skin, the sponsons are under
considerable pressure and some seepage of air may occur.
Reinflate as necessary. After paddling on hot days, release air
from sponsons, especially if leaving the kayak beached in full
sun on a hot day.
To Repair/Replace Sponson
The sponsons can be removed from the sleeve sewn to the
inside of the skin. Turn the skin inside out. The sponson
chamber is open at bow and stern ends. Tie a long string
through the hole in the tab at each end of the sponson. Pull
sponson through the center opening of the chamber (where
sponson hose is attached). To reinstall, pull the cord attached
to the sponson back through the chamber. Ensure sponson
is not twisted in the chamber.Inflate slightly to check fit.
Urethane glue and patches are included in the repair kit.
Duct tape will also work for the sponsons.
Feathercraft Kurrent 6
Feathercraft Kurrent 7
Kurrent Frame Parts
Large
Stern
Crossrib
Small
Crossribs–
Same for
Bow + Stern
Large Bow
Crossrib
Skin
Seat
Rim inserts
Deck Bars–
Same for
Bow + Stern
Chine + Gunwale
Extension Bars
(shown without
seat sling)
Foot Brace
Keel Extension
Bar with
Black Tape
1 SET OUT FRAME PARTS AS ILLUSTRATED
2 SHAKE OUT BOW & STERN FRAME
SECTIONS
• Theshockcordedtubingtakes
shape.
• ThebowhasBstampedon
plastic plate.
3 ATTACH SMALL CROSSRIBS TO BOW & STERN SECTIONS
• Pinonsmallcrossribinsertstoholeonblackblockonkeel
tube.
• Chineandgunwaletubessnap-fitontocrossrib.White
spacers are on “cockpit” side of crossrib.
Feathercraft Kurrent 8
Deck bar
Over-serts
•Rivetheadstofaceinto
kayak, not against skin.
Gunwales
Chines
Keel
Pin into block
4 UNFOLD SKIN
• Insertbowandsternframe.
• Velcrotabsareattachedtotheinsideofthehullalongthe
keel.
• Havethetabsopen.Checkthatalltherivetheadsonthe
frame section joins are facing towards the inside of the
kayak. This will avoid unncessary wear at these points.
• Slidebowandsternframesectionsintotheskin.
• Centertheframealongtheinsidekeelstrip,pushingthe
section to the very ends. Check that the keel tube aligns to
the strip along the inside keel.
5 SLIDE FOOT BRACE BAR ONTO BOW FRAME SECTION
• Webstraploopsaroundgunwalebar.
Feathercraft Kurrent 9
Insert bow frame section
Foot Brace Bar
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Feathercraft Boot Handbücher
Feathercraft
Feathercraft Sealskin 2000 Bedienungsanleitung
Feathercraft
Feathercraft Heron Bedienungsanleitung
Feathercraft
Feathercraft K1 Expedition Bedienungsanleitung
Feathercraft
Feathercraft K-Light Classic 2008 Bedienungsanleitung
Feathercraft
Feathercraft Wisper Bedienungsanleitung
Feathercraft
Feathercraft Klondike Bedienungsanleitung
Feathercraft
Feathercraft BayLee River Bedienungsanleitung
Feathercraft
Feathercraft K-Light Plus Bedienungsanleitung
Feathercraft
Feathercraft Khatsalano Bedienungsanleitung
Feathercraft
Feathercraft Kahuna Bedienungsanleitung
Beliebte Boot Handbücher anderer Marken
Raymarine
Raymarine ST70 Instrument Bedienungsanleitung
Pro-Line Boats
Pro-Line Boats Pro Line 19 Sport Bedienungsanleitung
Jeanneau
Jeanneau CAP CAMARAT 8.5 CC Bedienungsanleitung
Tiara Yachts
Tiara Yachts C49 2024 Bedienungsanleitung
Monterey Boats
Monterey Boats Sport Yacht 330 Bedienungsanleitung
J
J 105 Bedienungsanleitung
PURSUIT
PURSUIT OS 335 Bedienungsanleitung
Boston Whaler
Boston Whaler CONQUEST 345 Bedienungsanleitung
Jeanneau
Jeanneau SUN ODYSSEY 41 DS Bedienungsanleitung
Meridian
Meridian 490 Pilothouse Bedienungsanleitung
Advanced Elements
Advanced Elements AdvancedFrame Expedition AE1009 Bedienungsanleitung
Robo Marine Indonesia
Robo Marine Indonesia GEOMAR Bedienungsanleitung
