FEDERAL INDUSTRIES RSSL378 Montageanleitung

E3745

REV L 05/24/23

RSSL378, RSSL478, RSSL578, RSSL678

RSSL360, RSSL460, RSSL560, RSSL660

Self-Contained & Remote Models

NSSL378, NSSL478, NSSL578, NSSL678

Non-Refrigerated

INSTALLATION & OPERATION

INSTRUCTIONS

KEEP THIS MANUAL FOR FUTURE REFERENCE

Engineering and technical data are subject to change without notice.

FEDERAL INDUSTRIES 215 FEDERAL AVE Belleville, WI 53508

Toll Free 1(800) 356-4206 WI Phone (608) 424-3331 Fax: (608) 424-3234

Refrigerated Self-Serve Merchandiser (High Profile) Page 2

CONTENTS

INTRODUCTION .............................................................................................................4

WARNING LABELS & SAFETY INSTRUCTIONS..........................................................5

PRE-INSTALLATION PROCEDURES............................................................................6

Inspection For Shipping Damage......................................................................6

INSTALLATION INSTRUCTIONS...................................................................................6

Locating The Display Case.........................................................................................6

Grill Removal..............................................................................................................6

Removing Case From Shipping Skid..........................................................................7

Removing Packaging Material....................................................................................7

Leveling The Case......................................................................................................7

Condensate Evaporator..............................................................................................7

Lights..........................................................................................................................8

ELECTRICAL CONNECTION & GROUNDING INSTRUCTIONS...................................9

Electrical Supply Wiring ....................................................................................9

Grounding Requirements............................................................................9

Optional permanent connection ..................................................................9

OPERATING INSTRUCTIONS......................................................................................10

Initial Start-Up................................................................................................................10

Light Switch & Lights......................................................................................................10

LED Light Replacement.................................................................................................10

Digital Display.........................................................................................................................10

Placing Product in Case.................................................................................................10

Energy Saving Night Curtain..........................................................................................10

Electronic Temperature Control ....................................................................................11

Powering On Control......................................................................................................11

Adjusting Set Point.........................................................................................................12

Error Codes....................................................................................................................13

Optional Electronic Temperature Control ......................................................................14

Powering On Control......................................................................................................14

Adjusting Set Point.........................................................................................................15

Error Codes....................................................................................................................15

Temp Probe Common Resistance Chart.......................................................................16

ELECTRONIC CONTROL FUNCTIONALITY...............................................................17

Electronic Control............................................................................................17

Operation...................................................................................................17

Defrost Cycle..............................................................................................18

Control Factory Setting ..............................................................................18

Control Display................................................................................................19

Minimum Run Timer Feature ..........................................................................19

Maximum Run Timer Feature .........................................................................19

Refrigerated Self-Serve Merchandiser (High Profile) Page 3

REFRIGERATION OPERATION...................................................................................19

Self-Contained Refrigeration Operation..........................................................19

Dual Pressure Control ( Self-Contained Models Only )...................................19

Remote Refrigeration .....................................................................................20

Electronic Expansion Valve (EEV).............................................................20

Remote Refrigeration Operation .....................................................................21

CLEANING INSTRUCTIONS ........................................................................................22

Cleaning The Condenser Coil.........................................................................22

Cleaning The Condensate Pump....................................................................22

Cleaning The Acrylic Air Deflector...................................................................23

Daily Cleaning.................................................................................................23

Weekly Cleaning.............................................................................................24

SHELVES......................................................................................................................25

Installation & Removal.....................................................................................25

SERVICE INFORMATION.............................................................................................26

Pre-Service Checklist ...............................................................................................27

Special Service Situations ........................................................................................28

SALE & DISPOSAL ......................................................................................................28

Owner Responsibility................................................................................................28

REFRIGERATION & ELECTRICAL DATA .............................................................................29

RSSL378/360 ............................................................................................................29

RSSL478/460 ....................................................................................................30 & 31

RSSL578...........................................................................................................32 & 33

RSSL678...........................................................................................................34 & 35

NSSL378, NSSL478, NSSL578, NSSL678................................................................36

REPLACEMENT PARTS............................................................................................ 37 thru 44

RSSL DISPLAY AREA & VOLUME.........................................................................................45

WIRING DIAGRAMS................................................................................................... 46 thru 53

Refrigerated Self-Serve Merchandiser (High Profile) Page 4

INTRODUCTION

Thank you for purchasing a Federal Industries Merchandiser. This manual contains important instructions for

installing and servicing the RSSM, Refrigerated Self-Service Merchandisers. A repair parts list is also included in

the manual. Read all of these documents carefully before installing or servicing your case.

NOTICE

Read this manual before installing your case. Keep this manual and refer to it before doing any service

on the equipment. Failure to do so could result in personal injury or damage to the case.

NOTICE

Installation and service of the electrical components in the case must be performed by a licensed

electrician.

The portions of this manual covering components contain technical instructions intended only for persons

qualified to perform electrical work.

DANGER

Improper or faulty hookup of electrical components in the case can result in severe injury or death.

All electrical wiring hookups must be done in accordance with all applicable local, regional, or national

standards.

NOTE: UNIT MUST BE GROUNDED

REGISTRATION & SERIAL NUMBER

It’s important to keep a record of the model and serial number of your merchandiser for warranty and part

identification. Please write them here for your quick reference.

today.

Case Model__________________________ Serial Number______________________

We’re here to provide you with the best possible experience with your new product, however, we cannot cover

everything about your merchandiser in this manual, so if you have any additional questions or issues, please see

the SERVICE INFORMATION PAGE to find who you should contact.

Refrigerated Self-Serve Merchandiser (High Profile) Page 5

WARNING LABELS AND SAFETY

INSTRUCTIONS

This is the safety-alert symbol. When you see this symbol on your case or in the

manual, be alert to the potential for personal injury or damage to your equipment.

Be sure you understand all safety messages and always follow recommended precautions and safe

operating procedures.

NOTICE TO EMPLOYERS

You must make sure that everyone who installs, uses, or services your case is thoroughly

familiar with all safety information and procedures.

Important safety information is presented in this section and throughout the manual. The

Following signal words are used in the warning and safety messages:

DANGER: Severe injury or death will occur if you ignore the message.

WARNING: Severe injury or death can occur if you ignore the message.

CAUTION: Minor injury or damage to your case can occur if you ignore the message.

NOTICE: This is important installation, operation, or service information. If you ignore the

message, you may damage your case.

The warning and safety labels shown throughout this manual are placed on your Federal

Industries case at the factory. Follow all warning label instructions. If any warning or safety labels

become lost or damaged, call our customer service department at 1(800) 356-4206 for replacements.

This label is located on the back of the display case This label is located below the display pan.

and on the front of the case behind the access panel.

CAUTION

POWER BEFORE

RISK OF ELECTRIC

SHOCK DISCONNECT

91-12340

SERVICING UNIT.

CAUTION

HAZARDOUS MOVING PARTS

DO NOT OPERATE UNIT WITH

DISPLAY PANS REMOVED.

Refrigerated Self-Serve Merchandiser (High Profile) Page 6

PRE-INSTALLATION PROCEDURES

Inspection For Shipping Damage

You are responsible for filing all freight claims with the delivering truck line.

Inspect all cartons and crates for damage upon arrival. If there is damage to

shipping crates, cartons, or if a shortage is found, note this on (all copies) of

the Bill Of Lading prior to signing.

If damage is discovered when the case is uncrated, immediately call the delivering

truck line and follow-up the call with a written report indicating concealed damage to

your shipment. Ask for an immediate inspection of your concealed damaged item.

Crating material must be retained and shown to the inspector from the truck line.

INSTALLATION INSTRUCTIONS

Locating the Display Case NOTE: This case is designed for indoor use only.

The case should be located where it is not subjected to the direct rays of the sun,

heating ducts, grills, radiators, or ceiling fans, nor should it be located near open doors or

main door entrances. Avoid locations where there is excessive air movement or air disturbances

and avoid high humidity locations such as near cases with water misting or fogging devices.

The condenser air inlet is located in the front of the case. Do not block this inlet and do not

locate the air inlet near a source of heat. Clearance of 6” minimum must be maintained at the

back of the case for condenser discharge air. Clearance at the top of

the case should also be at least 8”.

Do not build this unit into an alcove and do not locate where condenser discharge air

cannot escape or where warm condenser air is allowed to re-circulate.

Grill Removal

WARNING: Electrical shock hazard. Do not operate unit with panels removed.

Must remove front and rear base grills for merchandiser installation. The front base grill

is secured with fast lead captive screws, and the rear base grill is secured with self

threading screws.

Both base grills must be replaced after merchandiser installation. Base grills must be

in place for proper operation of the merchandiser.

Refrigerated Self-Serve Merchandiser (High Profile) Page 7

Removing Case From Shipping Skid

CAUTION: If a Johnson bar or pry bar is used to move the case, make certain that

the case is lifted under the welded steel frame, and not by the end panels of the case.

Damage to the ends will result from lifting under the end panels.

Move the case as near as possible to the final location before removing it from the

shipping skid. Having removed the front and rear compressor compartment grills. Remove

the (three or four sets of bolts, nuts, and washers depending on case size) that secure the case to the

shipping skid. Discard these bolts, nuts, and washers.

Removing Packaging Material

Remove bubble wrap and packing material for all shelves, etc. If it is

necessary to remove tape residue from various materials, use cleaning

compounds recommended in the cleaning section of this manual.

Leveling the Case

The case must be level for proper drainage of defrost water to the condensate evaporator or

condensate pump.

Check the level of the case along the front rail and along the top of the display pan. Shim

under the case frame as needed to level the case. It is recommended that the leveled case be

sealed to the floor with an NSF Listed Sealant.

Condensate Evaporator

NOTICE: Steam from the condensate evaporator may be visible around the

base of the merchandiser during normal operation.

This merchandiser may be furnished with an electric condensate evaporator, or a

electric condensate pump. Plumbing connections are not required, unless

merchandiser is specifically ordered without a condensate evaporator or pump.

The condensate evaporator can be removed from the merchandiser and the

condensate drain can be plumbed to a external drain to conserve energy. To remove

the condensate evaporator, disconnect the wires at the condensate evaporator. This

must be done by a qualified electrician.

This is an open merchandiser and can produce a large amount of condensate water.

To ensure that adequate evaporator capacity is available, a high wattage heater is

used.

Make sure that the condensate drain line has not been dislodged during shipment and

that the drain trap terminates properly over the water reservoir.

Refrigerated Self-Serve Merchandiser (High Profile) Page 8

Lights

Standard Top Light

The case comes with one standard top light which is internally wired to the power

source. The light switch is located on the left top ceiling behind the air discharge honey comb.

Optional Shelf Lights

If optional shelf lights are furnished, make certain that the shelf light cords are completely

inserted into the sockets in the back panel and end of led lights or lights will not work

The power supply used on this case allows for removal of one or more shelf lights

without affecting the remaining lights.

When plugging or unplugging light cords, turn the light switch to the “off” position.

Refrigerated Self-Serve Merchandiser (High Profile) Page 9

ELECTRICAL CONNECTION AND

GROUNDING INSTRUCTIONS

Electrical Supply Wiring

DANGER: Improper or faulty hookup of electrical components in the

display case can result in severe injury or death.

THIS CASE MUST BE GROUNDED

Optional Permanent Connection

-Only a licensed electrician must perform all case electrical connections.

-All electrical wiring hookups must be done in accordance with all applicable local, regional, or

national electrical standards.

-A separate circuit for each display case is required to prevent other appliances on the same circuit

from overloading the circuit and causing malfunction.

-The electrical service must be grounded upon installation.

-See the electrical data plate located at the rear of the case for circuit load and wire current capacity.

-Standard Base Electrical Connection: The electrical connection box is accessible from the rear of the

case. Power Supply Wiring can be routed through the floor of the base frame or through the access

hole in the rear of the unit. Remove electrical box cover to access electrical connections.

POWER IN BOX POWER IN ACCESS HOLE

Refrigerated Self-Serve Merchandiser (High Profile) Page 10

OPERATING INSTRUCTIONS

Initial Start-Up

-After completing the items in the installation section of this manual. The case is ready

to be put into service. On self-contained models, the service valves on the refrigeration

system are back-seated when the unit leaves the factory.

-RSSL cases are designed to operate at 40º to 41º F. under ambient conditions not to

exceed 75º F. and 55% relative humidity.

-Nearly all open refrigerated merchandisers operate better when loaded with product than

when empty. If a check is made of the case operating temperatures, perform this check with

product in the case.

-Open refrigerated merchandisers are not intended as storage refrigerators and will not “pull

down” room temperature products efficiently. Load case interior with pre-chilled product only.

Light Switch And Lights

The light switch is located in the ceiling. This switch operates the interior lights only. If optional

shelf lights are installed, they are also controlled by this switch.

Led Light Replacement

The light is attached to the shelf with plastic spring clips. To remove a light, un plug cord from

end of bulb and pull down.

When replacing lights, use direct equivalents to the original bulbs.

Digital Display

This unit is equipped with an electronic temperature control with Digital Display.

The Display show a number 1 thru 9 to indicate temperature level.

Placing Product In Case

Do not overload the case with product to a point where the top air discharge grill or the

bottom air intake grill are blocked, or where the air curtain created by the discharge air is

blocked.

LOAD CASE INTERIOR WITH PRE-CHILLED 38deg OR COLDER

PRODUCT ONLY.

Energy Saving Night Curtain

This unit is equipped with an energy saving night curtain.

The night curtain is located in the top inside front of the canopy.

To use the night-curtain pull down and latch on front panel just below the

clear acrylic air deflector when case is not in use.

NOTICE: This refrigerated display case is designed to operate

in a maximum environment of 75 DEG. F and 55% relative

humidity. Exceeding these limits will cause poor case

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere FEDERAL INDUSTRIES Kaufmann Handbücher

FEDERAL INDUSTRIES

FEDERAL INDUSTRIES CD3628 Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

Hussmann

Hussmann ENTYCE TY3 Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

Hussmann

Hussmann CRFD Betriebsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

Hussmann

Hussmann WDCHI Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Hussmann

Hussmann Q2-SS Original Betriebsanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

Hussmann

Hussmann microSC SHM-A Series Bedienungsanleitung

Hussmann

Hussmann APT0500 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Hussmann

Hussmann Q1-SS Bedienungsanleitung

Hussmann

Hussmann impact Excel C2X-XLEP Bedienungsanleitung