Federal Signal Corporation EHorn-HV Kurzanleitung

Model eHorn-HV

Marine and Indoor/Outdoor

Rated Electronic Horn

Installation and Service Instructions

2645 Federal Signal Drive

University Park, Illinois 60484

www.fedsig.com

Customer Support 1-800-344-4634 • +1 708-534-4756 • [email protected]

Technical Support 1-800-755-7621 • +1 708-587-3587 • [email protected]

25500612A Rev. A0 1119 Printed in U.S.A.

Limited Warranty

This product is covered by a limited warranty, a copy can be found at

www.fedsig.com/SSG-Warranty.

Safety Messages to Installers and Users

This product should be installed to code in the country of use by qualied

personnel following all safety instructions below. Failure to do so may result in

property damage, serious injury, or death.

• Read and understand all instructions before installing, operating, or servicing

this equipment.

• Sound output will be severely reduced if any object are in front of the horn.

Keep front of horn free of obstruction.

• Do not connect this horn to the system or perform maintenance when power is

on.

• Do not paint the horn. No nish or coating is required. Paint may obstruct the

sound output, reducing the effectiveness of the horn.

• All effective warning horns produce loud sounds, which in certain

circumstances, may cause permanent hearing loss. Take appropriate

precautions such as wearing hearing protection. Recommendations in OSHA-

Sound Level Standard (29 CFR 1910) should not be exceeded.

• Establish a procedure to routinely check the signal system for proper activation

and operation.

• Never alter the unit in any manner.

• After installation and completion of initial system test, provide a copy of these

instructions to all personnel responsible for operation, periodic testing, and

maintenance of the equipment.

Unpacking the eHorn-HV

After unpacking the eHorn-HV, examine it for damage that may have occurred in

transit. If the horn has been damaged, do not attempt to install or operate it. File a

claim immediately with the carrier, stating the extent of the damage.

Carefully check all envelopes, shipping labels, and tags before removing or

discarding them. Disposal of all shipping materials must be carried out in

accordance with national and local codes and standards. If any parts are missing,

please contact Federal Signal Customer Support at 708-534-4756 or 800-344-

4634 or [email protected].

An Overview of the Model eHorn-HV

The Federal Signal eHorn-HV is a high output, continuous duty, marine and indoor/

outdoor-rated electronic horn with volume adjustment. The eHorn-HV is perfect for

use in high-ambient noise environments. The horn’s non-metallic, polycarbonate

housing is corrosion resistant and weatherproof for improved durability in harsh

industrial environments.

Installation and Service Instructions

Product Specications

Operating Voltages: eHorn-HV-024: 24VDC

Weight: eHorn-HV-024: 15.9 lbs

Housing Material: Polycarbonate

Brackets and Hardware: 304 Stainless Steel

Sound Pressure Level and Current Data

NOTICE – DO NOT USE UNSUITABLE TAPS: Not every tap is suitable for use

with all voltages and tones. Use of unsuitable taps signicantly reduces the

life of the product. The tables below identify the acceptable taps selection.

A table is also located on the rear cover of the product for quick reference.

Table 1 SPL and Current Data: eHorn-HV Model 52 Horn Tone

52 Horn Tone (315.6 Hz Steady)

LEVEL

TAPS SPL

(dBA @10 ft)

DC Current (A)

24VDCWIRE 1 WIRE 2

High P1 P4 116 3.0

Med P1 P3 109 1.0

Low P2 P3 100 0.4

NOTICE: Apply wires only to the positions designated in Table 1.

Other variations could cause damage to the eHorn-HV.

Table 2 SPL and Current Data: eHorn-HV Model 55/56 Horn Tone

55/56 Horn Tone (330.0 Hz Steady)

LEVEL

TAPS SPL

(dBA @10 ft)

DC Current (A)

24VDCWIRE 1 WIRE 2

High P1 P5 117 3.3

Med P1 P3 106 0.5

Low P2 P3 96 0.24

NOTICE: Apply wires only to the positions designated in Table 2.

Other variations could cause damage to the eHorn-HV.

Installation and Service Instructions

Mounting the eHorn-HV

The eHorn-HV can be mounted on any relatively at surface with the supplied

mounting brackets. The mounting surface must be capable of supporting the

weight of the eHorn-HV. Four installer-supplied 1/4" screws are required. Use

screws that are suitable for the mounting surface.

For dimensions, see Figures 1 and 2.

To secure the eHorn-HV to the mounting surface:

1. Hold the eHorn-HV against the mounting surface and use the four mounting

holes on the bracket as a template. Scribe drill-position marks on the

mounting surface.

2. Remove the eHorn-HV and drill a hole at each mark.

3. Secure the eHorn-HV to the mounting surface using installer-supplied

1/4" screws.

Figure 1

Depth and Height

with Bracket

Figure 2

Width and Height

with Brackets

9.43"/ 239.5 mm

.67"/ 17.0 mm

7.33"/ 186.2 mm

6.68"/ 169.7 mm

Weather pack sealed 2

contact male connector

9.43"/ 239.5 mm

7.62"/ 193.5 mm

6.0"/ 152.4 mm

11.48"/ 291.6 mm

4X Ø

0.27"/ 6.85 mm

10.75"/ 273.1 mm

Installation and Service Instructions

Opening and Closing the Housing

The factory-supplied leads are strain-relieved to the cover.

HOUSING DAMAGE: Use caution and support the housing when loosening

the cover screws. The housing is not supported by any means other than

the cover screws. Once they are loosened, the housing will separate from

the cover.

Opening the Housing

Tools required: 7/16" socket, 3/8" socket,

1/4" socket and a 6" extension

1. Remove the four 1/4"-20 locknuts on

the bracket assembly to free the lower

band bracket.

2. Remove the four 1/4"-20 hex head

screws from the back of the bracket

assembly to allow the eHorn-HV to be

free of the bracket assembly

3. See Figure 4. Loosen the four cover

screws while supporting the housing so

it does not fall. (The cover screws are

retained in the housing).

Figure 4 Locations of Housing Screws

Cover Screws (4 Places)

Figure 3

eHorn-HV Bracket

Assembly

Installation and Service Instructions

Closing the Housing

4. Verify that the cover gasket is in the groove around the perimeter of the

cover.

5. Align the housing with the cover. Note that the FS logo on the front of the

eHorn-HV needs to be oriented correctly with the arrow on the inside of the

cover or the two parts will not t together.

6. See Figure 3 for bracket assembly instructions.

7. Tighten the cover screws hand tight, then torque them to 60 in-lb ± 10 in-lb.

Wiring the eHorn-HV

SHOCK HAZARD: To avoid electrical shock, do not connect

wires when the circuits are energized.

The external leads and connector must be suitably protected to prevent damage.

Use grommets, bushings, and wires ties to protect them from abrasion. The horn

is provided with 12” 14AWG wire leads with an Aptiv (Delphi) 2P male connector

(Aptiv p/n 12010973) for customer connection. Wire polarity is as follows: red +

(positive), black - (negative).

Figure 5

Tone Generator/

Amplier Board

See installation manual or

the product cover

for tap settings

Tone

Selection

P1 P3 P4 P5

Power

DC Power

Connector

Input

Power

Tap

Wires

(-)(+)

Power Taps

55/56

7.5

Installation and Service Instructions

Selecting the Tone

Setting the Tone Volume

The volume of the eHorn-HV is adjusted by tap selection on the tone generator/

amplier board.

Activating the Horn

To activate the horn, apply the appropriate line voltage to the horn power input

connector. The horn remains active as long as line voltage is present.

Technical Assistance

For technical assistance, contact our technical support team at +1-708-587-3587

or [email protected].

Repair Service

Product repair service requires a return authorization from Federal Signal. For

repair service, contact your Authorized Federal Signal Distributor or Federal

Signal customer support at +1 708-534-4756 or [email protected]. Defective

products that are returned within the warranty period will be repaired or replaced

at Federal Signal’s sole discretion.

Product Returns

Product returns require a return authorization from Federal Signal prior to

returning the product. Please contact your Authorized Federal Signal Distributor

for more information regarding our return policy or to request a product return.

Products returned for repair require a Return Authorization form from your local

distributor or from Federal Signal. To obtain repair service or technical assistance

from Federal Signal, call 800-755-7621 or 708-587-3587. For instruction manuals

and information on related products, visit: www.fedsig.com

The eHorn-HV is factory-set to the 52 tone. To select the 55/56 eHorn-HV tone,

move the jumper on the tone generator/amplier board (Figure 5 on page 6).

Signaling Devices

2645 Federal Signal Drive

University Park, IL 60484-3167

Tel: 708-534-4756

Tech Support Tel: 708-587-3587

Email: [email protected]

www.fedsig.com

25500612A Rev. A0 1119 Printed in U.S.A.

Inhaltsverzeichnis

Andere Federal Signal Corporation Horn Handbücher

Federal Signal Corporation

Federal Signal Corporation 350 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 41X Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation 3H Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vibratone 350WBX Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 350 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 55X Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation 450E Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 31X Series Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation 52 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 450EWBX-024 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation eHorn Kurzanleitung

Beliebte Horn Handbücher anderer Marken

Elk Products

Elk Products 45 Bedienungsanleitung

Valcom

Valcom V-1050C Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock DB3 Series Bedienungsanleitung

Altec Lansing

Altec Lansing 811B HF HORN Bedienungsanleitung

RF Elements

RF Elements UltraHorn CC Series Bedienungsanleitung

Edwards Signaling

Edwards Signaling 869DSTR-G1 Series Montageanleitung

Valcom

Valcom V-1030C Bedienungsanleitung

Valcom

Valcom VIP-130AL-SA Bedienungsanleitung

Electro-Voice

Electro-Voice HPT94 Bedienungsanleitung

Toa

Toa LE-M124 Bedienungsanleitung

EAW

EAW MR-102B Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR MH30 Bedienungsanleitung

Pequod

Pequod TWISTER 3.1 Bedienungsanleitung

United Pacific

United Pacific 46151 Bedienungsanleitung

Wolo

Wolo OCEAN ALERT 170 Bedienungsanleitung

Vixen Horns

Vixen Horns VXO8315B/4114B Bedienungsanleitung

Altec

Altec 151A PAGING HORN Bedienungsanleitung

aidapt

aidapt VM953 Programmierhandbuch

Federal Signal Corporation eHorn-HV Kurzanleitung

Beliebte Horn Handbücher anderer Marken