Federal Signal Corporation IS-I-IP15 Series Bedienungsanleitung

Signaling Standalone Manual

25500842

Rev. A0 0423

Printed in U.S.A.

Informer15 Speaker

Model IS-I-IP15 Series C

Indoor/Outdoor Audible Speaker

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to [email protected] or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of tness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484

www.fedsig.com

Customer Support 1-800-344-4634 • +1-708-534-4756

Technical Support 1-800-755-7621 • +1-708-587-3587

All product names or trademarks are properties of their respective owners.

Signaling Standalone Manual

Federal Signal www.fedsig.com

Contents

Safety Messages......................................................................................................................................................5

Safety Messages to Installers .............................................................................................................................5

General Description ................................................................................................................................................7

Overview .............................................................................................................................................................7

Features..............................................................................................................................................................8

Ordering Information ...........................................................................................................................................9

Specications ..........................................................................................................................................................9

Installation..............................................................................................................................................................12

Flat Surface Mounting.......................................................................................................................................12

Opening the Housing ........................................................................................................................................13

Wiring the Network and Power Connections ....................................................................................................14

PoE model (See Figure 2) ........................................................................................................................14

24 Vdc model (See Figure 3)....................................................................................................................15

Wiring to the Controller Board...........................................................................................................................15

Closing the Housing..........................................................................................................................................17

Testing ....................................................................................................................................................................17

Programming .........................................................................................................................................................18

Automatic Volume Level Control.......................................................................................................................18

Digital Inputs .....................................................................................................................................................18

WAV Files..........................................................................................................................................................18

WAV File Control Commands ...................................................................................................................18

Function Control Commands ............................................................................................................................19

Conguring Informers Using the Web Interface................................................................................................19

1. Conguring the Network Interface ........................................................................................................20

2. Conguring the RTU Settings ...............................................................................................................24

3. Conguring the Multicast Zones ...........................................................................................................30

4. Conguring Security..............................................................................................................................33

5. Conguring the User Setup...................................................................................................................34

6. Uploading Certicates...........................................................................................................................36

7. Uploading Firmware..............................................................................................................................37

8. Rebooting Device and Loading Conguration Settings ........................................................................ 38

Informer15 Speaker (Model IS-I-P15 Series C)

Federal Signal www.fedsig.com

Tables

Table 1 Ordering Information .................................................................................................................................9

Table 2 Electrical Requirements ............................................................................................................................9

Table 3 Connectors and Jacks for the Controller Board ...................................................................................10

Table 4 Connectors and Jacks for the Amplier Board .....................................................................................10

Table 5 Connectors and Jacks for the PoE Board (PoE models only) ............................................................. 11

Table 6 Connectors for the 24 Vdc Power Board ............................................................................................... 11

Table 7 Visual Indications for the Controller Board ........................................................................................... 11

Table 8 Visual Indications for Amplier Board ................................................................................................... 11

Table 9 Environmental and Physical ................................................................................................................... 11

Table 10 Input and Output Conguration ...........................................................................................................18

Table 11 Examples of Illegal WAV Files ...............................................................................................................19

Table 12 Replacement Parts .................................................................................................................................42

Table 13 Standard DV Messages..........................................................................................................................43

Table 14 UTM Tones ..............................................................................................................................................50

Figures

Figure 1 Depth and Height of Informer15 Speaker............................................................................................. 13

Figure 2 IS-I-IP15 PC Boards................................................................................................................................14

Figure 3 IS-I-IP15-024 PC Boards.........................................................................................................................15

9. Restoring Conguration to Factory Defaults.........................................................................................39

10. Logging Out of the Web Interface.......................................................................................................41

Maintenance...........................................................................................................................................................42

Ordering Replacement Parts ............................................................................................................................42

Getting Service ......................................................................................................................................................42

Appendix A Standard DV Messages....................................................................................................................43

Safety Messages

Signaling Standalone Manual

Federal Signal www.fedsig.com

Safety Messages

It is important to follow all instructions shipped with this product. This device is to be

installed by trained personnel who are thoroughly familiar with the country’s electric

codes and will follow these guidelines as well as local codes and ordinances, including

any state or local noise-control ordinances.

Planning

• The sound output of sirens is capable of causing permanent hearing damage. To

prevent excessive exposure, carefully plan siren placement, post warnings, and

restrict access to areas near sirens. Review and comply with any local or state noise

control ordinances as well as OSHA noise exposure regulations and guidelines.

After installation, service, or maintenance, test the system to conﬁrm that it is operating

properly. Test the system regularly to conﬁrm that it will be operational in an emergency.

Safety Messages to Installers

People’s lives depend on the safe installation of our products. It is important to follow

all instructions shipped with this product. This device is to be installed by a trained

electrician who is thoroughly familiar with the National Electrical Code and/or Canadian

Electrical Code and will follow the NEC and/or CEC Guidelines as well as all local codes.

The selection of the mounting location for this Informer15 Speaker, its controls, and

the routing of the wiring is to be accomplished under the Facilities Engineer and the

Safety Engineer direction. Listed below are some other important safety instructions and

precautions you should follow:

• Electrocution or severe personal injury can occur when performing various

installation and service functions, such as making electrical connections, drilling

holes, or lifting equipment. Therefore, only experienced electricians should install this

product per national, state, and any other electrical codes having jurisdiction. Perform

all work under the direction of the installation or service crew safety foreman.

• Read and understand all instructions before installing, operating, or servicing this

equipment.

• All eective warning sounds may, in certain circumstances, cause permanent

hearing loss. Take appropriate precautions, such as wearing hearing protection. The

maximum sound level exposure limits speciﬁed in OSHA 29 CFR 1910 should not be

exceeded.

• For optimum sound distribution, do not install this speaker where objects would block

any portion of the front of the Informer15 Speaker.

• Do not paint the Informer15 Speaker. No ﬁnish or coating is required. Paint may

obstruct the sound output, reducing the eectiveness of the horn.

• Establish a procedure to check the signal system for proper activation and operation

routinely.

• Any maintenance to the unit MUST be performed by a trained electrician per NEC

Guidelines and local codes.

Safety Messages

Informer15 Speaker (Model IS-I-P15 Series C)

Federal Signal www.fedsig.com

• Never alter the unit in any manner.

• The nameplate should NOT be obscured, as it contains cautionary and/or other

information of importance to maintenance personnel.

• After installation and completion of the initial system test, provide a copy of these

instructions to all personnel responsible for the operation, periodic testing, and

equipment maintenance.

• File these instructions in a safe place and refer to them when maintaining and/or

reinstalling the device.

Failure to follow all safety precautions and instructions may result in property damage,

serious injury, or death.

Installation and Service

• After installation or service, test the system to conﬁrm that it is operating properly.

Test the system regularly to conﬁrm that it will be operational in an emergency.

• If future service and operating personnel do not have these instructions to refer to,

the system may not provide the intended audible warning, and service personnel

may be exposed to death, permanent hearing loss, or other bodily injuries. File

these instructions in a safe place and refer to them periodically. Give a copy of these

instructions to recruits and trainees. Give a copy to anyone who is going to service or

repair the Informer15 Speaker.

• To reduce the risk of electric shock, do not perform any servicing other than what

is contained in the operating instructions unless you are qualiﬁed to do so. Refer all

servicing to qualiﬁed service personnel. Always test the Informer15 Speaker before

using after repairs have been made.

Ethernet Wiring

• Unless shielded or run in conduit, Ethernet wiring must be at least six feet from bare

power wiring or lightning rods and associated wires, and at least six inches from

other wire (for example, antenna wires, doorbell wires, wires from transformers to

neon signs), steam or hot water pipes, and heating ducts.

• Do not place Ethernet wiring or connections in any conduit, outlet, or junction box

containing high voltage electrical wiring.

• If using a cable gland, the gland must be UL listed. The Informer15 Speaker has a

1/2-inch NPT entry size.

Symbol Deﬁnition

_A _V Indicates to reduce the risk of ﬁre, replace the fuse as marked.

Pay careful attention to the notice located on the equipment.

Read and understand the information contained in this manual before attempting

to install or service the siren.

General Description

Signaling Standalone Manual

Federal Signal www.fedsig.com

General Description

Overview

The Informer15 Speaker is a 15-watt, IP-enabled indoor and outdoor speaker. Use the

Informer15 as a warning and alert device with both audible and visual indicators. The

audible capabilities include locally stored, high-quality, high-powered tones and voice

messages. The visual indicators include an integrated high-powered LED light and

an optional scrolling message display that can be controlled by the Informer15. The

Informer15 can be equipped with up to four local initiation devices (switches) to activate

the unit locally.

The Informer15 Speaker has an internal 15-watt ampliﬁer/driver to deliver tone warnings

and intelligible voice messages from Informer15 stored memory.

The Informer15 is programmed and conﬁgured as a standalone device to only use the

inputs to activate the Informer15. This may be useful if the location has no network

connectivity but where voice and tone alerts from locally activated inputs are required.

The Informer15 includes one output to control the visual indicator and an output to

activate an external relay, which can be used to control external devices. The Informer15

has two 1/2-inch NPT openings on the bottom of the speaker for simple installation of

pipe-mount devices. The openings allow access to LAN, open collector output, and

activation inputs.

The Informer15 is designed for outdoor use and large indoor structures. A 24 Vdc and

a POE+ model are available. The POE+ version of the Informer15 obtains its operating

voltage solely from a POE+ (IEEE 802.3at) network switch or power injector. No other

AC or DC power is required for the integrated speaker or light. All wiring interfaces

are accessible via internal connectors and built-in NPT entrances for quick and easy

installation.

The Informer15 Speaker is a perfect addition to existing notiﬁcation systems where lack of

coverage exists. The unit can be used as a call station where emergency alert buttons are

required.

General Description

Informer15 Speaker (Model IS-I-P15 Series C)

Federal Signal www.fedsig.com

Features

The Informer15 has the following features; some features require using the Commander®

software system:

• Outdoor or indoor IP-enabled speaker for audible and visual alerts

• Out-of-the-box standard programming. Changes to the conﬁguration can be made

using our web interface found on www.fedsig.com.

• Out-of-the-box conﬁguration (All modes are maintained and normally open)

• Tone 1 – NFPA Temporal Coded Slow Whoop, LED on

• Tone 2 – Alternating High-Low, LED on

• Tone 3 – Rapid Siren (Yelp), LED on

• Tone 4 – Steady Horn (Euro-Toxic), LED on

• Speaker rated at 112 dB for tones and 107 dB for pink noise at 10 feet

• Seven standard built-in warning signals: Wail, Steady, Alternate Wail, Alternate Steady,

Pulsed Wail, Pulsed Steady, Auxiliary Chime

• Broadcasts prerecorded voice or tone ﬁles

• Deliver intelligible voice messages from locally prerecorded ﬁles

• Removable microSD card for custom message generation. Store up to 4000 voice or

tone messages that total up to 17 hours of recording time.

• Ambient-noise-level monitoring with automatic volume control

• Individually conﬁgured for volume and noise-level adjustments

• Wall mount

• Four local alarm initiation inputs to activate unit locally or standalone operation

Momentary mode: contact closure sounds the alarm for the programmed duration.

Continuous mode: sounds the alarm for duration of the closure.

• One open collector output paired with 24 Vdc for controlling an external relay

• High-intensity LED light that can be activated independently or with messages

• Models available with white, red, amber, blue, and green LED lights

• Wide variety of ﬂash patterns

• Power over Ethernet using 802.3at PoE+ 25.5 W or 24 Vdc powered (two models)

• Wide operating temperature range

• Allows remote software upgrades

• NEMA 4X Enclosure

• UL and cUL listed

• Complies with FCC Title 47, Part 15

Specications

Signaling Standalone Manual

Federal Signal www.fedsig.com

Ordering Information

Table 1 Ordering Information

Part Number Description

IS-I-IP15-W 15 W PoE Speaker with white high-output LED

IS-I-IP15-R 15 W PoE Speaker with red high-output LED

IS-I-IP15-A 15 W PoE Speaker with amber high-output LED

IS-I-IP15-B 15 W PoE Speaker with blue high-output LED

IS-I-IP15-G 15 W PoE Speaker with green high-output LED

IS-I-IP15-024W 15 W, 24 Vdc, Speaker with white high-output LED

IS-I-IP15-024R 15 W, 24 Vdc, Speaker with red high-output LED

IS-I-IP15-024A 15 W, 24 Vdc, Speaker with amber high-output LED

IS-I-IP15-024B 15 W, 24 Vdc, Speaker with blue high-output LED

IS-I-IP15-024G 15 W, 24 Vdc, Speaker with green high-output LED

Specications

Table 2 Electrical Requirements

Input Power for PoE model Power over Ethernet (PoE+ 802.3at) 48 Vdc

Requires 25.5 W

Input Power for 24 Vdc model 24 Vdc, 1.0 A

Serial Port Protocol FLASH programming and conguration

Default: 9600 bit/s, 8 data, 1 stop, no parity.

Congurable up to 115,200 bit/s

Open Collector Output Maximum 30 V or 100 mA maximum,

(speaker provides +24 Vdc, 20 mA maximum for external

relay)

Ethernet Port for PoE model IEEE 802.3, 10/100 Base-T connection with PoE+

802.3at, Type 2, 25.5 W

Ethernet Port for 24 Vdc model IEEE 802.3, 10/100 Base-T connection

Alarm Initiating Inputs Four optically Isolated Inputs

Audio Storage Warning siren audio, seven factory-installed tones: Wail,

Steady, Alternate Wail, Alternate Steady, Pulsed Wail,

Pulsed Steady, Auxiliary Chime

Prerecorded les—up to 4000 messages with up to

17 hours of recording time

Audio Data 8 bit 8 kHz mono WAV

Audio Frequency response 300 Hz to 3000 Hz, +1 to -3 dB per octave

Maximum Audio Output 15 W, 112 dB for tones and 107 dB for pink noise at

10 feet

Power Output 15 W into 8 ohm load

Frequency response +/- 3 dB from 300-6.0 kHz

THD < 5% at output

Hum and Noise < -45 dB

Input Levels 1.77 VRMS (5 VP-P), 10 VRMS(28.3 VP-P) and 25 VRMS

(70.7 VP-P)

Specications

Informer15 Speaker (Model IS-I-P15 Series C)

Federal Signal www.fedsig.com

Table 3 Connectors and Jacks for the Controller Board

JP1 LED Lamp Test

Short pins 1 and 2 to turn on LED lamp

JP2 Inputs

1 – ISO-GND

2 – Input #1

3 – ISO-GND

4 – Input #2

5 – ISO-GND

6 – Input #3

7 – ISO-GND

8 – Input #4

JP3 LED Lamp Output

1 – GND

2 – Power, switched +24 Vdc

JP4 Test mode

JP5 Factory Default

Short pins 1 and 2 to restore to factory defaults

JP6 Open Collector Output

1 – Output #1 Open Collector Output

2 – Output #1 +24 Vdc

JP8 Option1 Jumper

Short pins 1 and 2 for Standalone Option

JP9 Option2 Jumper

Short pins 1 and 2 for Option

JP11 Serial Port RJ25 6 conductor mod jack

JP12 Controller to Amplier Interface

JP13 microSD FLASH card holder

M1 Communications from PoE board

Table 4 Connectors and Jacks for the Amplier Board

JP1 Power Input from PoE board or the 24 Vdc power board

JP2 Balanced Audio Input – 10 or 25 VRMS in (Not used)

JP3 Audio Input Select Jumper (Not used with I-IP15 conguration.)

Jumper 1 and 2 = 25 VRMS input

Jumper 3 and 4 = 10 VRMS input

JP4 Amplier to Controller Interface

Pin1 (-) Speaker output

Pin2 (+) Speaker output

VR1 Amplier Gain (For max volume, turn clockwise.)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Sprecher Handbücher

Federal Signal Corporation

Federal Signal Corporation MS100-01 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation UltraVoice RF100U Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation MODULATOR Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer15 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer100 Speaker Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer100 Speaker Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MS100-01 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AM30 Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation DS100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation UltraVoice RF100UX Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Modulator MOD Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MicroPulse MPS U Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer15 I-IP15 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 50GC Selectone Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DSA1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SST3-MV Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DSA1X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer100 Speaker Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AUDIOMASTER AM300 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IS-I-IP15X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ES100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DS100X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SelecTone 300GC Kurzanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung