FeelElec FY6800 Series Bedienungsanleitung

FeelElec

FY6800 Series Fully Numerical Control

Dual Channel Function/Arbitrary Waveform Generator

User’s Manual

Rev1.1 April,2018

Guaranty and Declaration

Declaration

● FeelElec reserves the right to modify or change parts of or all the

specifications and pricing policies at company’s sole decision.

●Information in this publication replaces all previously corresponding material.

● FeelElec shall not be liable for losses caused by either incidental or

consequential in connection with the furnishing, use or performance of this

manual as well as any information contained.

●Any part of this document is forbidden to be copied or photocopied or

rearranged without prior written approval of FeelElec.

If you have any problem or requirement when using our products or this

manual, please contact FeelElec.

Tel：0086 371 68997005 E-mail：[email protected]

Website：www.feelelec.com

Contents

Guaranty and Declaration.............................................................................................I

Product Introduction..................................................................................................... 4

Quick Start ....................................................................................................................... 7

General Inspection.................................................................................................... 7

Front Panel Overview............................................................................................... 8

Back Panel Overview...............................................................................................11

Power On and Inspection....................................................................................... 12

User Interface .......................................................................................................... 13

Appearance and Dimensions...................................................................................... 15

Front Panel Operations .............................................................................................. 16

Waveform Output.................................................................................................. 16

Select Output Channel.......................................................................................................16

Select Waveform ................................................................................................................17

Set Frequency.....................................................................................................................18

Set Amplitude......................................................................................................................19

Set Offset.............................................................................................................................20

Set Duty Cycle (Square)....................................................................................................21

Set Phase............................................................................................................................22

Enable Output.....................................................................................................................23

Example：Output Sine Waveform...................................................................................24

Turn on burst function......................................................................................... 28

Frequency Meter/Counter................................................................................... 29

Enable the Counter............................................................................................................29

Set the Counter...................................................................................................................30

Sweep....................................................................................................................... 31

Sweep Object......................................................................................................................31

Sweep Start Position..........................................................................................................32

Sweep End Position...........................................................................................................33

Sweep Time.........................................................................................................................34

VCO (Voltage Control Output) Sweep.............................................................................34

Sweep Type.........................................................................................................................35

Enable Sweep Function.....................................................................................................36

System Configuration and Auxiliary Functions............................................ 37

Save and Load....................................................................................................................38

Configuration.......................................................................................................................39

Uplink ...................................................................................................................................40

Synchronization..................................................................................................................41

Troubleshooting........................................................................................................... 42

Technical Specification .............................................................................................. 43

Appendix ........................................................................................................................ 47

4FY6800 Series User’s Manual

Product Introduction

This manual applies to each model of FY6800series Function/Arbitrary

Waveform Signal Generator. The last three characters of the model indicate the

up limit output of Sine Wave (MHz). For example, the “60M”of the Model Number

“FY6800-60M”indicates the Sine wave maximum output frequency is up to

60MHz.

FY6800series Dual-channel Function / Arbitrary waveform generator is a set

of Function Signal Generator, Arbitrary Waveform Generator, Pulse Generator,

Analog / Digital modulator, VCO, Sweep, Counters and Frequency Meter and

other functions in a high Performance, cost-effective, multi-function signal

generator. Abundant shortcut keys and graphical user interface simplifies every

operation. Users do not have to spend a lot of time to learn and familiar with the

operation of the instrument, you can be skilled use. For education, research and

development, production, testing, maintenance and other industries to provide a

new choice.

The instrument adopt the Direct Digital Synthesizer (DDS) technology

and provide stable, precise, pure and low distortion signals. Surface mounting

technology improves interference immunity and operational life span. Can output

up to 97 groups of functions / arbitrary waveform, contains 33 groups of preset

waveforms and 64 groups of user-defined waveforms. Preset waveforms: Sine,

Square (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set

accurately), Triangle/Ramp, CMOS(0~10V), Four channels TTL, Exponential

Rise, Exponential Fall, Noise, ECG, DC etc.

FY6800 Series User’s Manual 5

Main Features:

Adopt the Direct Digital Synthesizer (DDS) technology and provide stable,

precise, pure and low distortion signals.

Desktop design with ABS plastic housing, AC 100 - 240V (AC) wide voltage

supply;

2.4 inch TFT Color LCD with 320×240 resolution, displaying parameters and

graphics of the two channels at the same time.

The instrument uses 14-bit high-speed D/A converter chip (5Vpp output

quantization error is less than 1mV), 250MSa/s sample rate, 14bits vertical

resolution.

Fully independent dual-channel output (equivalent to two independent signal

sources), able to work synchronously, and the phase difference can be

accurately adjusted;

Equipped with channel tracking function, when the tracking function is turned

on, all parameters of both channels can be updated according to the user's

configuration at the same time;

Two or more instruments can synchronize multiple instruments through the

SYNC port;

Up to 98 sets of function/arbitrary waveforms can be output, including 34 sets

of preset waveforms and 64 sets of user-defined waveforms. Preset

waveforms include: sine wave, square wave (duty ratio adjustable), triangle

wave, pulse wave (preset pulse width and frequency can be precisely set),

rise sawtooth wave, ramp sawtooth wave, staircase wave, trapezoidal pulse

wave, Sink Pulse, narrow pulse, noise, exponential rise, exponential drop,

electrocardiogram, Lorentz pulse, multiple audio waves, CMOS (0~10V),

four-channel TTL level and DC voltage;

Enable to store 64 arbitrary waveform data files, each one of waveform

storage depth 8192 points * 14bits;

High frequency accuracy: Frequency accuracy can reach 10-6 orders of

magnitude;

The frequency resolution is relatively high: the full-range frequency resolution

is 1uHz (0.000001Hz);

Amplitude resolution is higher:Amplitude resolution can be as low as 1mV

(0.001V);

With -10V~+10V DC bias function (<20MHz), resolution up to 1mV;

6FY6800 Series User’s Manual

The duty cycle of both channels can be adjusted independently, with an

accuracy of 0.01%;

The phase adjustment range of the two channels is 0~359.99°, and the

adjustment accuracy is 0.01°;

No range limit: The full range of frequency is not divided into gear switches,

program-controlled settings;

With digital signal output function, it can realize any CMOS level with 0~10V

amplitude;

Scanning function: It can scan the four properties of the signal: frequency,

amplitude, offset, and duty cycle. It has two scanning modes: linear scan and

logarithmic scan. The scan time can reach 999.99S. The start and end of the

scan can be set arbitrarily ;

Burst Output Function: There has Manual Trigger, internal CH2 Trigger, and

External Trigger for your options. It can output 1~1048575 pulse trains.

VCO function: Support VCO voltage control signal output function (such as

voltage controlled oscillator).

Various modulation types: AM, FM, PM, ASK, FSK and PSK modulations.

100M Frequency meter function: It can measure frequency, period, pulse

width and duty cycle. Max. frequency workable is 100MHz and Min.

frequency workable is 0.01 Hz.

Counter Function: It has 2 coupling measure modes including DC coupling

and AC coupling. This design can solve inaccuracy problem of AC coupling.

All parameters can be calibrated by internal procedures;

Equipped with powerful arbitrary waveform editing function, it can edit

arbitrary waveform on PC and download to instrument output waveform;

Powerful communication features that can be controlled using a PC. Open

communication protocol makes secondary development very simple;

Standard dual full functional channels which are equivalent to two

independent generators.

High reliability: Large-scale integrated circuit, surface mount technology, high

reliability, long service life;

Output short-circuit protection: All signal outputs can work under load

short-circuit conditions 60S or more;

Can choose our FYA2000S series or FPA1000 series power amplifier to

output 20W~100W signal in DC-10MHz width without any distortion.

FY6800 Series User’s Manual 7

Quick Start

General Inspection

Please follow the items below when you receive a new FY6800series

Function/Arbitrary Waveform Generator.

1．Inspect the shipping container for damage

Keep the damaged shipping container or cushioning material until the

contents of the shipment have been checked for completeness and the

instrument has passed both electrical and mechanical tests. The consigner or

carrier shall be liable for the damage to instrument resulting from shipment.

2．Inspect the instrument

In case of any damage, or defect, or failure, notify your FeelElec sales

representative.

3．Check the accessories

Please check the accessories according to the Appendix C ( packing lists). If

the accessories are incomplete or damaged, please contact your FeelElec sales

representative.

8FY6800 Series User’s Manual

Front Panel Overview

The front panel is divided into several function areas for easy operation.

Front Panel

Item

Function

Description

LCD

2.4 inch TFT（320×240）color LCD. Operation instruction please check

chapter “User Interface”.

Manu

Buttons

Manu buttons are matched with Manu displayed on the LCD. Press

corresponding button to activate submenu represented.

Function

Buttons Area

Waveform selection button:

—You can switch between sine, square wave, triangle

wave, and any type of arbitrary wave.

—Change the selected channel signal type.

Trigger and modulation function buttons

—Can set a specific number of pulse train output

function（BURS）

—Modulation mode can be set :ASK、FSK、PSK、AM、

FM、PM

Sine, square, sawtooth and arbitrary waveforms can be

scanned.

—Supports scanning of four parameters of frequency,

amplitude, offset, and duty cycle.

Supports two linear and logarithmic scanning methods.

Can switch to frequency meter and counter function,

measure frequency, period, duty cycle, positive pulse

width of external input signal

—Supports DC and AC signal input.

FY6800 Series User’s Manual 9

—Supports 1 s, 10 s and 100 s gate time switching.

—Dual channel output can work with frequency meter

measurement.

VCO function can be set

—Support VCO voltage control signal generator's

frequency, amplitude, offset, duty cycle and other

parameter output functions (such as

voltage-controlled oscillator).

Used to set auxiliary function parameters and system

parameters.

—Supports storage of 20 sets of parameters such as

frequency, amplitude, offset, and phase

—Support Chinese and English switching

—Support tone off/on

—Supports multi-machine cascading

—Supports master/slave switchover in cascaded state

—Supports dual-channel power-on default output state

setting

Arrows

Press Arrow buttons to select figure which you want to edit when setting

values of each parameter.

ADJ Knob

When using the knob to set parameters, you can increase (clockwise)

or decrease (counterclockwise) the value at the current cursor.

Power

Button

The power indicator will remain on when it is turned on.

When the signal generator is turned off, the indicator light will enter the

breathing lamp state and CH1 and CH2 will stop outputting (the output will

remain at 0 volts).

CH1 channel

output

connector

BNC connector, nominal output impedance 50Ω.

When channel CH1 is on (the CH1 button indicator lights up), the connector

outputs the waveform in the current configuration of CH1.

Channel

control, OK

button

It is used to control the output of the CH1 channel and can be

switched to the CH1 parameter setting interface in any

interface.

—Press this button, the CH1 light will turn on, and the CH1

output will turn on. At this point, the [CH1] connector outputs

the signal in the current configuration.

—Press this button again, the indicator light goes off, and at

this point, the CH1 output is turned off.

Confirm button

—When editing frequency parameters, press this key to

change the frequency unit.

—When scanning the interface, press this button to start/stop

scanning.

10 FY6800 Series User’s Manual

It is used to control the output of the CH1 channel and can be

switched to the CH1 parameter setting interface in any

interface.

—Press this button, the CH2 light will turn on, and the CH2

output will turn on. At this point, the [CH2] connector outputs

the signal in the current configuration.

—Press this button again, the indicator light goes off, and at

this point, the CH2 output is turned off.

CH2 channel

output

connector

BNC connector, nominal output impedance 50Ω.

When channel CH2 is on (the CH2 button indicator lights up), the connector

outputs the waveform in the current configuration of CH2.

AC coupling

measuring

terminal

BNC connector, input impedance 100Ω. For inputting signal of meter or

counter.

Inhaltsverzeichnis

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung