Fein FSC1.6Q Bedienungsanleitung
FEIN REPAIR TOOLS
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FSC 1.6 Q / FSC 2.0 Q
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
2/49
Summary
1. Technical data
2. Maintenance
3. Electrical function check
4. Disassembly
5. Assembly
6. Tools
7. Extracts from the operating instructions
8. Modifications, extras, repair information
Spare parts lists and exploded view diagram are available online at:
www.fein.de/Fein Service/Fein Ersatzteile
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
3/49
1. Technical data
Order number new 7 236 42 7 236 36
Model new FSC 1.6 Q FSC 2.0 Q
Power / consumption watts 400
Power / output watts 220
Oscillations rpm 11000 - 18500
Mains supply type 1~
Protection class lI
Length of cable with plug m 5
Weight without cable kg 1.25
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
4/49
2. Maintenance
2.1. Provisions
2.2. Cleaning and care
2.3. Replacing carbon brushes
2.4. Repair and maintenance intervals
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
5/49
2.1. Provisions
Provisions:
Please note that power tools may only be repaired, maintained and checked by a trained
electrician, as improper repairs can result in serious risks to the user (BGV A2).
Repeated inspections are to be carried out in accordance with DIN VDE 0702-1.
The regulations in accordance with DIN VDE 0701 Part 1 should be observed after
repairs.
Only use original FEIN spare parts!
The relevant accident prevention regulations of the employers’liability insurance
associations are to be observed when commissioning.
The German Equipment and Product Safety Act applies for correct use.
Outside Germany, the regulations applicable in the relevant country must be observed!
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
6/49
2.2. Cleaning and care
Risk of injury through accidental switching on.
Unplug before undertaking any maintenance.
Once a week, or more often in the case of frequent use:
•Check cable (160) for damage
•Clean cooling apertures
•Blow out the inside of the power tool from the outside
with dry compressed air through the ventilation openings.
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
7/49
2.3. Replacing carbon brushes
The machine is fitted with carbon brushes with self-cutoff.
When checking the carbon brushes, make sure they are reinserted in the same
position and can move easily in the carbon brush holder.
When the carbon brushes wear down to a length of 7mm they need to be
replaced with new ones.
Only use original FEIN carbon brushes as this is the only way to ensure
compliance with EMC requirements!
Run in new carbon brushes for 20 minutes without load at the lowest possible
speed.
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
8/49
2.4. Repair and maintenance intervals
After approx. 300 operating hours:
•Dismantle machine, clean, and blow out or brush down insulating parts,
replace spherical bearing (500)
Depending on type and duration of use, but at least every 6 months:
•Dismantle machine
•Clean machine thoroughly
•Replace bearing (armature)
•Clean electronics (dry cleaning only)
•Check cable and inner stranded wires for chafe marks
•Check that plug contacts are snugly fitting
•Replace spherical bearing (500)
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
9/49
3. Electrical function check
3.1. Function check
3.2. Test data
3.3. Test equipment and tools
3.4. Circuit diagram / connection diagram
3.5. Safety test
All rights reserved by FEIN, especially in case of industrial rights registration.
Any power of disposition such as copying and right of transfer is situated with FEIN. Sahre / MVK 04 / 13
FEIN REPAIR TOOLS
10/49
3.1. Function check
3.1.1. Without mains, connected to mains
3.1.2. Motor
3.1.3. Electronics
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Fein Elektrowerkzeuge Handbücher
Fein
Fein 7 230 26 Einrichtungshandbuch
Fein
Fein BLS1.6X Bedienungsanleitung
Fein
Fein ASsd 636-1 Bedienungsanleitung
Fein
Fein KBM 50 Q Bedienungsanleitung
Fein
Fein MultiMaster AFMM18QSL Bedienungsanleitung
Fein
Fein QSz 7 49 Bedienungsanleitung
Fein
Fein FSC 1.7 Q Bedienungsanleitung
Fein
Fein AMM 500 Plus Series Bedienungsanleitung
Fein
Fein ASg 636 Kinetik Bedienungsanleitung
Fein
Fein AGWP10 Bedienungsanleitung
Fein
Fein FSC1.6X Bedienungsanleitung
Fein
Fein BLS 3.5 Kurzanleitung
Fein
Fein AWBP 10 Einrichtungshandbuch
Fein
Fein MM700-1.7 Bedienungsanleitung
Fein
Fein BLs 1.6 Bedienungsanleitung
Fein
Fein ASW 10-6-2ST Bedienungsanleitung
Fein
Fein ASCM18QM Series Bedienungsanleitung
Fein
Fein MSxe 636 II Bedienungsanleitung
Fein
Fein KBH25 Betriebsanleitung
Fein
Fein SCW 16-6 Bedienungsanleitung
