Ferris SNAPPER PRO EZ Dump Bedienungsanleitung

Not for

Reproduction

Not for

Reproduction

2 ferrismowers.com | snapper.com

Table of Contents:

General Information..............................................................3

Products Covered by this Manual.......................................3

Operator Safety..................................................................... 3

Safety Rules and Information...........................................3

Safety Decals................................................................... 4

Safety Icons......................................................................4

Installation............................................................................. 4

Rear Suspension Adjustment (Models Equipped with

Rear Suspension).............................................................5

Remove the Carburetor Shield.........................................6

Install the Hopper Mounting Plate....................................6

Install the Stabilizer Straps (Models with Flat Plate

Bumpers)........................................................................ 10

Install the Support Plate and Latch Bar Assembly......... 12

Install the Torsion Tube................................................. 12

Install the Mount Tube and Latch Bar Assemblies to the

Support Plates................................................................12

Install the Latch Bar Assembly Tensioning Spring......... 13

Install the Dump Handle Assembly................................ 13

Install the Rod Pivot Mount............................................ 14

Install the Dump Handle Linkage Rods..........................14

Connect the Latch Bar Assemblies to the Latch Bar...... 15

Install the Door Latch Rod............................................. 15

Install the Winch Anchor Bracket................................... 15

Install the Winch Quick Mount....................................... 16

Install the Weights and Weight Mounts..........................16

Install the Handle on the Winch..................................... 17

Install the Hopper to the Hopper Mount......................... 17

Adjust the Dump Handle Position.................................. 18

Adjust the Latch Bar Assemblies................................... 18

Adjust the Dump Handle Linkage Rods......................... 18

Install Tube Extension to Hopper................................... 19

Install Hose to Hopper Assembly................................... 19

Install Hose to Blower Assembly....................................19

Operation............................................................................. 19

General Operating Instructions...................................... 20

Opening and Closing the Hopper...................................21

Lubrication...................................................................... 21

Troubleshooting.................................................................. 22

Troubleshooting Charts.................................................. 22

Unplugging a Clogged Unit............................................ 22

Collector System Removal................................................ 23

Not for

Reproduction

General Information

Thank you for purchasing this quality-built grass collection

system. When operated and maintained according to the

instructions in this manual, your grass collection system will

provide you many years of dependable service.

This manual contains safety information to make you aware

of the hazards and risks associated with this product and

how to avoid them. This product is designed and intended to

be used and maintained according to the manual for grass

collection from established lawns and is not intended for any

other purpose. It is important that you read and understand

these instructions thoroughly before attempting to operate

this equipment. Save these original instructions for future

reference.

These setup instructions are to be done in addition to the

Blower and Blower Mount installation instructions detailed

in the blower's operators manual included with the blower

mount.

You must observe and obey all safety instructions in the

blower's operator's manual along with all instructions detailed

in this manual.

The images in this document are representative, and

are meant to complement the instructional copy they

accompany. Your unit may vary from the images

displayed.LEFTandRIGHTare as seen from the operator's

position.

Date of

Purchase:

FERRIS is a trademark of Briggs & Stratton, Milwaukee, WI,

USA.

SNAPPER PRO is a trademark of Briggs & Stratton,

Milwaukee, WI, USA.

Products Covered by this

Manual

TURBO-Pro Blower w/ 12 cu. ft. EZ Dump Hopper

System

Number

Description

5600901 Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 61", 200XT, IS2100Z, F210Z

5600902 Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 52", IS2100Z

5600904 Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 52", 150XT, F160Z

5601243 Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 52", ISX2200

5601245 Kit, 12 cu. ft. EZ Dump Hopper w/ TURBO-Pro MAX

Blower, 61", ISX2200

FAST-Vac® Blower w/ 12 cu. ft. EZ Dump Hopper

System

Number

Description

FAST-Vac® Blower w/ 12 cu. ft. EZ Dump Hopper

5600903 Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

61", 200XT, IS2100Z, F210Z

5600905 Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

52", 150XT, F160Z

5600906 Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

52", IS2100Z

5601242 Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

52" ISX2200

5601244 Kit, 12 cu. ft. EZ Dump Hopper w/ FAST-Vac® Blower,

61" ISX3300

TURBO-Pro Blower w/ 14 cu. ft. EZ Dump XL Hopper

System

Number

Description

5600910 Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61", IS3200Z, F320Z

5600900 Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61", S200XT

5900940 Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61", F210Z

5601241 Kit, 14 cu. ft. EZ Dump XL Hopper w/ TURBO-Pro MAX

Blower, 61" ISX3300

FAST-Vac® Blower w/ 14 cu. ft. EZ Dump XL Hopper

System

Number

Description

5600907 Kit, 14 cu. ft. EZ Dump XL Hopper w/ FAST-Vac®

Blower, 61", IS3200Z, F320Z

5600909 Kit, 14 cu. ft. EZ Dump XL Hopper w/ FAST-Vac®

Blower, 61", S200XT

5600941 Kit, 14 cu. ft. EZ Dump XL Hopper w/ FAST-Vac®

Blower, 61", F210Z

5601240 Kit, 14 cu. ft. EZ Dump XL Hopper w FAST-Vac® Blower,

61" ISX3300

Operator Safety

In addition to all of the safety instructions described in this

manual, you must obey all the safety instructions in the

blower's operators manual included with the blower mount.

Safety Rules and Information

Read these safety instructions and follow them closely.

Failure to obey these rules could result in loss of control of

unit, severe personal injury or death to you, or bystanders, or

damage to property or equipment.

This mowing deck is capable of amputating hands and

feet and throwing objects.

The triangle ( ) in text signifies important cautions or

warning which must be followed.

Not for

Reproduction

4 ferrismowers.com | snapper.com

WARNING

• Check the collection system to make sure it is bolted

tightly to the rider.

WARNING

• When blower assembly is removed from the mower

deck, the deflector must be properly installed.

WARNING

Amputation and thrown objects hazard

If the mower stalls or the turbo blower chute plugs:

1. Disengage the blower (blades) and remove the ignition

key and wait for all parts to stop before disconnecting

or unlatching any parts attached to the blower or the

collection system.

2. Remove the foreign object or clear the chute with a

suitable tool, such as a broom handle, before restarting

the engine. NEVER place hands into the blower

housing to clear jammed objects. Blower may rotate

when object is removed.

WARNING

For added rider stability and to prevent tipping or loss of

control:

• Use reduced speed on uneven ground and when

turning corners.

• Reduce loads on hillsides. It is recommended that the

collection system be kept no more than half full when

negotiating any slopes. Start mowing on slopes when

the collection system is empty.

Safety Decals

Before operating your unit, read the safety decals. The

cautions and warnings are for your safety. To avoid a

personal injury or damage to the unit, understand and follow

all the safety decals.

WARNING

If any safety decals become worn or damaged and cannot

be read, order replacement decals from your dealer.

A. Part Number: 5104315 - Decal, Container, Icons

Safety Icons

Warning - Thrown objects hazard:

• Do not open collection system container with engine

running.

• Do not operate with blower or collection system tube

unlatched or missing.

• Operate only with both the entire collection system and

front counterbalance weights installed and the collection

system closed and latched.

Warning - Loss of traction and control hazard:

• Do not operate with only the collection system installed.

• Do not operate with only the front counter balance

weights installed.

• Operate only with both the entire collection system and

front counter balance weights installed and the collection

system closed and latched.

Installation

In addition to these installation instructions, perform the

installation instructions for the blower and blower mount that

are detailed in the blower's operators manual included with

the blower mount.

Not for

Reproduction

Rear Suspension Adjustment (Models

Equipped with Rear Suspension)

Many units equipped with rear suspension has multiple upper

mounting positions for the rear shock assembly (A, Figure

1). If the unit that you are installing the collection system

on is equipped with rear suspension, the upper mounting

position of the rear shock assembly must be re-positioned to

accommodate the additional weight of the collection system.

Some units are equipped with two (2) upper shock mounting

positions and some units are equipped with three (3) upper

shock mounting positions. To accommodate the additional

weight of the collection system the upper end of the shock

mount assembly must re-positioned so that the shock is in its

most vertical orientation.

If the unit that you are installing the collection system on does

not have additional upper mounting positions, the spring's

pre-load must be adjusted. For unit's with additional upper

mounting positions: if a stiffer ride is desired after the rear

shock is re-positioned to it's most vertical position, it can be

achieved by adjusting the spring's pre-load.

To adjust the upper shock mounting position:

1. Park the machine on a flat, level surface. Engage the

parking brake, disengage the PTO, turn the ignition

switch to OFF, and remove the key from the ignition.

2. Chock the front wheels of the unit to prevent the machine

from rolling.

3. Raise the rear of the machine and secure with jack

stands. The jack stands must be positioned under the

bumper of the unit.

4. Position the jack under the suspension cradle (or the

cross member that ties the suspension arms together,

depending on your unit) and slowly raise the rear

suspension to relieve the pressure on the upper shock

mounting bolts.

Note:This will require small adjustments to the jacks position.

The shock should move freely on the mounting bolt when the

pressure is relieved.

5. Remove the upper shock mounting hardware and

pivot the shock to the position that orients the shock

most vertically (position #2 for units with two (2) upper

mounting positions; position #3 for units with three (3)

upper mounting positions). Adjust the jack to align the

shock assembly to the shock mounting hole.

6. Re-install the upper shock mounting hardware and

tighten securely.

7. Remove the jack from underneath the suspension cradle

(or suspension cross member, depending on your unit).

8. Remove the jack stands from underneath the machine.

To adjust the spring pre-load:

1. Park the machine on a flat, level surface. Engage the

parking brake, disengage the PTO, turn the ignition

switch to OFF, and remove the ignition key.

2. Chock the front wheels of the machine to prevent the

machine from rolling.

3. Raise the rear of the machine and secure with jack

stands.

4. Remove the rear drive tires.

WARNING

Use two hands when adjusting the shock assembly springs.

The will prevent the wrench from slipping while pressure is

being applied.

5. To adjust the spring pre-load of the shock assembly

(A, Figure 2) insert the tip of the spanner wrench (p/n

5022853) (B), that came with the zero-turn riding mower,

into the notch of the pre-load adjuster (C). While holding

the spanner wrench in place with one hand, turn counter-

clockwise to increase the amount of pre-load. (Turning

clockwise will decrease the amount of pre-load.) Make

sure that both rear shock assemblies are adjusted to the

same pre-load position.

Not for

Reproduction

6 ferrismowers.com | snapper.com

6. Re-install the rear drive tires. Torque the lug bolts to

85-91 ft. lbs. (115-129 Nm). Remove the jack stands from

under the machine.

Note:If the spanner wrench is not located in a clamp under

the seat plate of your unit, it was included with the publication

packet for the zero-turn riding mower.

Remove the Carburetor Shield

If a unit has a carburetor shield it must be removed prior to

installing the collection system.

Note:ISX2200 and ISX3300 series models DO NOT need

the carburetor shield removed.

1. If the engine is hot, allow sufficient time for the muffler to

cool to prevent a burn injury during installation process.

2. Remove the carburetor shield (A, Figure 3) from the top

of the rear bumper (B) by removing the hardware (C, D &

E) securing the shield to the bumper.

Install the Hopper Mounting Plate

All zero-turn riding mowers with mid-mounted mower decks

that this hopper collection system fits use the same hopper

mount plate but use different hardware and mounting holes to

mount it. Please refer to the following instructions and figures

for the proper mounting holes and hardware for mounting the

hopper mount.

Zero-Turn Riding Mowers with Round Tube

Bumpers

Four (4) 3/8 U-bolts (A, Figure 4) and eight (8) 3/8-16 hex

nylock flange nuts (B) are used to mount the hopper mount

Not for

Reproduction

F160Z with 52" Mower Deck (12 cu. ft. Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the top bumper tube and

through the holes indicated as "A" in Figure 5 and secure

with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the middle bumper tube and

through the holes indicated as "B" in Figure 5 and secure

with four (4) 3/8-16 nylock flange nuts.

3. Center the hopper mount plate on the bumper and tighten

the hardware.

IS2100Z with 52" Mower Deck (12 cu. ft. Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the top bumper tube and

through the holes indicated as "A" in Figure 6 and secure

with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the middle bumper tube and

through the holes indicated as "B" in Figure 6 and secure

with four (4) 3/8-16 nylock flange nuts.

3. Center the hopper mount plate on the bumper and tighten

the hardware.

IS2100Z with 61" Mower Deck (12 cu. ft. Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the top bumper tube and

through the holes indicated as "A" in Figure 7 and secure

with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the middle bumper tube and

through the holes indicated as "B" in Figure 7 and secure

with four (4) 3/8-16 nylock flange nuts.

3. Slide the hopper mount plate as far as it will go towards

the discharge side of the mower deck and tighten the

hardware.

ISX2200 with 52" Mower Deck (12 cu. ft.

Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the middle bumper tube and

through the holes indicated as "A" in Figure 8 and secure

with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the bottom bumper tube and

through the holes indicated as "B" in Figure 8 and secure

with four (4) 3/8-16 nylock flange nuts.

3. Center the hopper mount plate on the bumper and tighten

the hardware.

ISX2200 with 61" Mower Deck (12 cu. ft.

Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the middle bumper tube and

through the holes indicated as "A" in Figure 9 and secure

with four (4) 3/8-16 nylock flange nuts.

Not for

Reproduction

8 ferrismowers.com | snapper.com

2. Install two (2) U-bolts over the bottom bumper tube and

through the holes indicated as "B" in Figure 9 and secure

with four (4) 3/8-16 nylock flange nuts.

3. Slide the hopper mount plate as far as it will go towards

the discharge side of the mower deck and tighten the

hardware.

F210Z with 61" Mower Deck (12 cu. ft. Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the top bumper tube and

through the holes indicated as "A" in Figure 10 and

secure with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the middle bumper tube and

through the holes indicated as "B" in Figure 10 and

secure with four (4) 3/8-16 nylock flange nuts.

3. Slide the hopper mount plate as far as it will go towards

the discharge side of the mower deck and tighten the

hardware.

F210Z with 61" Mower Deck (14 cu. ft. Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the top bumper tube and

through the holes indicated as "A" in Figure 11 and

secure with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the middle bumper tube and

through the holes indicated as "B" in Figure 11 and

secure with four (4) 3/8-16 nylock flange nuts.

3. Center the hopper mount plate on the bumper and tighten

the hardware.

IS3200Z with 61" Mower Deck (14 cu. ft. Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the top bumper tube and

through the holes indicated as "A" in Figure 12 and

secure with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the second bumper tube (from

the top of the bumper counting down) and through the

holes indicated as "B" in Figure 12 and secure with four

(4) 3/8-16 nylock flange nuts.

3. Center the hopper mount plate on the bumper and tighten

the hardware.

ISX3300 with 61" Mower Deck (14 cu. ft.

Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the second bumper tube (from

the top of the bumper counting down) and through the

holes indicated as "A" in Figure 13 and secure with four

(4) 3/8-16 nylock flange nuts.

Not for

Reproduction

2. Install two (2) U-bolts over the third bumper tube (from

the top of the bumper counting down) and through the

holes indicated as "B" in Figure 13 and secure with four

(4) 3/8-16 nylock flange nuts.

3. Center the hopper mount plate on the bumper and tighten

the hardware.

F320Z with 61" Mower Deck (14 cu. ft. Hopper)

1. Position the hopper mount plate onto the bumper and

install two (2) U-bolts over the top bumper tube and

through the holes indicated as "A" in Figure 14 and

secure with four (4) 3/8-16 nylock flange nuts.

2. Install two (2) U-bolts over the second bumper tube (from

the top of the bumper counting down) and through the

holes indicated as "B" in Figure 14 and secure with four

(4) 3/8-16 nylock flange nuts.

3. Center the hopper mount plate on the bumper and tighten

the hardware.

Zero-Turn Riding Mowers with Flat Plate

Bumpers

3/8-16 X 1" bolts, 3/8 SAE washers, and 3/8-16 nylock flange

nuts are used to mount the hopper mount plate to the flat tube

bumper.

Please see the instructions below for your specific model,

mower deck size, and collection system as each installation

process is slightly different for units with flat plate bumpers.

S150XT with 52" Mower Deck (12 cu. ft. Hopper)

1. Position the hopper mount plate (A, Figure 15) onto the

bumper (B) and route four (4) 3/8-16 X 1" bolts (C) and

3/8 flat washers (D) through the holes identified as "A" in

Figure 16 and then through the bumper and secure with

four (4) 3/8 hex nylock flange nuts (E).

2. Route two (2) 3/8-16 X 1" bolts and 3/8 flat washers

through the holes identified as "B" in Figure 16 and then

through the bumper and the hopper mount backing plate

(F) and secure with two (2) 3/8 hex nylock flange nuts.

Not for

Reproduction

10 ferrismowers.com | snapper.com

S200XT with 61" Mower Deck (12 cu. ft. Hopper)

1. Position the hopper mount plate (A, Figure 17) onto the

bumper (B) and route four (4) 3/8-16 X 1" bolts (C) and

3/8 flat washers (D) through the holes identified as "A" in

Figure 18 and then through the bumper and secure with

four (4) 3/8 hex nylock flange nuts (E).

2. Route two (2) 3/8-16 X 1" bolts and 3/8 flat washers

through the holes identified as "B" in Figure 18 and then

through the bumper and secure with two (2) 3/8 hex

nylock flange nuts.

3. Route one (1) 3/8-16 X 1" bolt and a 3/8 flat washer

through the hole identified as "C" in Figure 18 and then

through the bumper and secure with one (1) 3/8 hex

nylock flange nut.

S200XT with 61" Mower Deck (14 cu. ft. Hopper)

1. Position the hopper mount plate (A, Figure 19) onto the

bumper (B) and route four (4) 3/8-16 X 1" bolts (C) and

3/8 flat washers (D) through the holes identified as "A" in

Figure 20 and then through the bumper and secure with

four (4) 3/8 hex nylock flange nuts (E).

2. Route two (2) 3/8-16 X 1" bolts and 3/8 flat washers

through the holes identified as "B" in Figure 20 and then

through the bumper and secure with two (2) 3/8 hex

nylock flange nuts.

3. Route two (2) 3/8-16 X 1" bolts and 3/8 flat washers

through the holes identified as "C" in Figure 20 and then

through the bumper and secure with two (2) 3/8 hex

nylock flange nuts.

Install the Stabilizer Straps (Models with

Flat Plate Bumpers)

Models with flat plate bumpers utilize stabilizer straps to help

mount the hopper mount plate to the unit. Each series, deck

size, and hopper combination has it's own specific stabilizer

straps and unique orientation. Your kit only has the stabilizer

straps for the machine the hopper kit that was purchased was

intended to be installed on.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ferris Rasen- und Gartengeräte Handbücher

Ferris

Ferris 1000z Series Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung