Ferroli Optima 801 Bedienungsanleitung

801

WALLMOUNTED, ROOM SEALED,

FAN ASSISTED, GAS COMBINATION BOILER

Stockton Close, Minworth Industrial Park, Minworth, Sutton Coldfield, West Midlands B76 8DH

Tel.: 0121/3523500 - Fax 0121/3523510

ALL SPECIFICATIONS SUBJECT TO CHANGE

Phone numbers:

Installer

Service Engineer

Serial No.

Read these Instructions thoroughly

before using the appliance

FERROLI HELPLINE

FOR SERVICE INFORMATION OR

HELP TELEPHONE: 0121 3523500

ALWAYS QUOTE YOUR SERIAL NUMBER

FOR IMMEDIATE ASSISTANCE

USERS

INSTRUCTIONS

Appr. Nr. B94.02A CE 0063AQ2150

04/98

G.C. NO: 47-267-17

801

Conditions of Installation

GAS SUPPLY

It is the law that all gas appliances are installed and serviced by a competent person in accordance with the

Gas Safety Regulations (Installation & Use) 1994, and the manufacturers instructions. Failure to observe

these requirement may lead to prosecution.

ELECTRICAL SUPPLY 230 V ~ 50 Hz FUSED 3A.

The electrical wiring must be carried out by a qualified electrician.

The colours of the wires in the mains lead of this appliance may not correspond with the coloured markings

identifying the terminal in the plug. Therefore proceed as follow:

Thewirecolouredgreenandyellowmustbeconnectedtotheterminalintheplugmarkedwitheithertheletter

E or by the earth symbol or coloured green or green and yellow. The wire coloured blue must be connected

totheterminalmarkedeitherwiththeletterNorcolouredblack.Thewirecolouredbrownmustbeconnected

to the terminal marked either with the letter L or coloured red.

MINIMUM CLEARANCE

The minimum clearance around the appliance should be as follows:

Sides 5 mm

Front 600 mm

Below200 mm

Above100 mm

Note:Ifasideoutletflueistobeused,aclearanceof75mmwillbeneededontheflueoutletsideoftheboiler.

Green/Yellow earth

Live Brown

Cable clamp

Fused 3 Amp plug to B.S. 1363

Neutral Blue

801

Boiler Lighting Instructions

Important: the Control

system has a built in waiting

time for Central Heating.

A max. 3 minutes delay

following shut down of

Boilerstat, Clock, Roomstat

oruseofHotWaterisnormal.

1. Open control panel cover by pulling at either side.

2. Ensure that the C.H./D.H.W. selector switch is set for: "Heating Continuous and Hot Water".

3. Ensure that the electricity supply is turned on.

4. Ensure that the heating system is filled with water and has not been drained down.

(Pressure gauge should read 1.0 bar minimum).

5. Adjust the room thermostat (if fitted) to a high setting.

6. Adjustthe boilerthermostat toits maximumsetting. Aftera waitingtime ofmax 3minutes, fanin boiler

will commence to run after which boiler will fire.

7. Setthetimeclock(iffitted),roomthermostat(iffitted)andtheboilerthermostattotheirdesiredsettings.

Note 1 - The main burner will light whenever a hot tap is turned on.

Note2-Iftheflamefailurelockoutlight(withinknob)isilluminatedwait10secondsandpresstheflame

failure reset knob, the boiler should then light

To Shut Down The Boiler For Short Periods

1. SettheC.H./D.H.W.selectorswitchtohotwater.(Inthispositionthepilotburnerwillremainalight,and

the main burner will only operate when domestic hot water is required).

AUTO

OVERRIDE

12:31

AUTO

Flame viewing

opening

C.H. pressure

gauge

C.H. boiler

thermostat

Fault diagnostic lights Domestic hot water thermostat

Time clock

Flame

failure

reset knob

C.H./D.H.W. selector switch

801

To Shut Down The Boiler For Long Periods

1. Turn off the electricity supply.

Boiler Controls

1.0 CENTRAL HEATING SELECTOR SWITCH

The central heating selector switch has three positions, these are:

a) Heating Timed & Hot Water

For domestic hot water supply and central heating controlled by the time clock.

b) Hot Water

For domestic hot water supply only.

c) Heating Continuous & Hot Water

For the domestic hot water supply and continuous central heating.

Note - When central heating is not required the selector switch must be turned to the position marked "Hot

Water".

2.0 TIME CLOCK (if fitted)

If a time clock is fitted to the boiler to control the Central Heating, this will come into operation when

the Selector Switch is turned to the position marked "Heating timed and Hot Water"

3.0 BOILER THERMOSTAT TEMPERATURE SETTING

Theboilerwatertemperaturecanbesetbytheboilerthermostatknob,whichisvariablefromminimum

to maximum. This control knob does not affect the temperature of the domestic Hot Water.

4.0 DOMESTIC HOT WATER THERMOSTAT TEMPERATURE SETTING

Thedomestic hotwater temperaturecanbe setbythe D.H.W.thermostat knob,whichis variablefrom

minimum to maximum. This control knob does not affect the temperature of the central heating.

5.0 DOMESTIC HOT WATER

When any domestic hot water tap is turned on the boiler will provide hot water. With the domestic hot

water thermostat knob to maximum, minimum flow rate the water will be approximately 70°C and a

maximum flow rate the water will be approximaterly 40°C (normal running is approximaterly 60°C).

6.0 SERVICING

Theboilermustbecheckedandservicedbyyourinstallerorothercompetentpersonatleastonceayear.

General Notes

1.0 ESPACE OF GAS

Should a gas leak be suspected, turn off the gas supply at the meter then contact the Local Region of

British Gas P.L.C. without delay.

2.0 SYSTEM WATER PRESSURE

Ifthe waterpressurein thecentralheating system,asindicated bythepressure gauge,fallsbelow 1.0

bar, contact your installer, Service Engineer or other competent person to top it up.

801

3.0 VENTILATION

If the appliance is installed in a compartment or cupboard, do not obstruct any purpose provided

ventilation openings. Do not use the compartment or cupboard for storage purposes.

4.0 FROST PROTECTION

Note - The boiler has its own built-in frost protection which automatically fire the boiler in low

temperature situations irrespective of the selector switch setting. Electricity supply must be left on.

Forfrostprotectionofthesystem(radiator,etc.),afrostthermostatcanbefitted,oriftheboileristurned

off for long periods contact your installer or other competent person to drain the system. The system

must be re-filled by your installer or other competent person.

5.0 HIGH LIMIT CUT-OFF THERMOSTAT

The boiler is fitted with a safety overheat cut-off thermostat, should it operate the pilot burner will go

out.Shouldthishappen,waitatleast3minutesbeforeattemptingtore-lighttheboiler.Theboilershould

be relight in accordance with the «Boiler Lighting Instructions». If the safety overhead cut-off

thermostat continues to fail consult your installer, service engineer or other competent person.

6.0 Ifthepumpsticks,itcanusuallybefreedbyremovingthechromecenterscrew(asmallamountofwater

will escape) and manually free the impeller using a screwdriver in the end of the shaft.

Simple Checks

Ifafaultissuspectedordiscovered,youshouldcontactyourinstaller,serviceengineerorothercompetentperson.

The following list however, is a series of simple checks that should be made before contacting your installer:

a) Is the plug properly located in the socket and 3 amp fuse intact?

b) Is the electricity supply switch on?

c) Is gas supply on and is pilot alight?

d) Is the room thermostat (if fitted) set high enough?

e) Is the boiler thermostat set high enough?

f) Is the time clock in the ON position? (i.e. calling for central heating)

g) Are the radiator valves open?

h) Is the central heating selector switch set correctly?

i) Is the pressure on the pressure gauge indicating more than 1 bar?

Time Clock

A 24 hour time clock is fitted to the boiler to control the central heating, this will come into operation when the selector

switch is turned to the position marked “heating timed and hot water”.

AUTO

OVER RIDE

12:31

RDP

AUTO P

ASlide switch: set clock - auto - set programme

BDisplay. Symbol in Display = Timer ON

PSelect programme ON/OFF 1.....8

DPush buttons Time + Time

EOverride: Boiler will switch ON if boiler is OFF;

and OFF if is ON

FI=Heating continuous - AUTO=Heating timed - O=Heating disabled

RReset (with pencil) only with switch Ain set clock position

801

1.1 Use buttons + and - to set 1st ON time eg. 6:00

Display

2.1 Use buttons + and - to set OFF time, eg. 9:00

Display

3.1 Use button + and - to set 2nd ON time, eg. 12:30

Display

4.1 Use button + and - to set 2nd OFF time eg. 14:00

Display

5.1 Use button + and - to set 3rd ON time, eg. 16:00

Display

6.1 Use button + and - to set 3rd OFF time eg. 23:30

Display

8. On completion of programming slide switch (A) toAuto

position, the time of day will be displayed and the cen-

tral heating will switch ON and OFF according to the

programme set.

1. Slide switch (A) to right position (P)

Display

2. Press button (P)

Display

3. Press button (P)

Display

4. Press button (P)

Display

5. Press button (P)

Display

6. Press button (P)

Display

7. The timer can be programmed with up to 8 ON and

8 OFF times by repeating the above procedure.

To set time of day

1. Slide switch (A) to left position

2. Using button + and

adjust until the correct time is shown on display (B).

Pre Set Programmes. The timer is pre programmed with 3 ON and 3 OFF times.

6:30 - 8:30

12:00 - 12:00

16:30 : 23:30

6:30

16:00

8:30

29:00

If these are suitable no programming is required and the slide switch (A) can be

moved to theAuto position and the central heating will be ON for these periods.

(12:00 - 12:00 will not switch on the boiler)

12:00

312:30

12:00

414:00

16:30

22:30

16:00

23:30

To Set Own ON and OFF times. Symbol in Display = ON time

Over ride

By pressing the over ride button (E) the timer programme is over ridden ie, if programme is in OFF time it will

come ON and if in ON time will go OFF.

The timer will revert back to it set programme on reaching the next ON or OFF time.

When the programme is on over ride the sign will be shown in the display window (B).

Reset Button

By the use of a pencil the reset button can be pushed (R). This will clear all programmes apart from those

factory pre set.

Reset is only possible with switch (A) in set Clock position!

Stockton Close, Minworth Industrial Park, Minworth, Sutton Coldfield, West Midlands B76 8DH

Tel.: 0121/3523500 - Fax 0121/3523510

ALL SPECIFICATIONS SUBJECT TO CHANGE

BECAUSE OF OUR CONSTANT ENDEAVOUR FOR IMPROVEMENT DETAILS MAY VARY

SLIGHTLY FROM THOSE QUOTED IN THESE INSTRUCTIONS.

Phone numbers:

Installer

Service Engineer

IMPORTANT:

If thepump sticks, it can usually be freed by removing the chromecenterscrew,(asmall

amount of water will escape) and manually free the impeller using a screwdriver in the end

of the shaft.

Cod. 3540251/1 - 04/98

Andere Handbücher für optima 801

Inhaltsverzeichnis

Andere Ferroli Kessel Handbücher

Ferroli

Ferroli OPTIMAX HE 31 S Bedienungsanleitung

Ferroli

Ferroli TP3 COND 65-1000 Service-Handbuch

Ferroli

Ferroli Optimax 25 C Fehlerbehebungshandbuch

Ferroli

Ferroli BLUEHELIX 352 RRT 24 C Technisches Handbuch

Ferroli

Ferroli GN1 N Bedienungsanleitung

Ferroli

Ferroli BLUEHELIX TECH RRT 24 H Technisches Handbuch

Ferroli

Ferroli OPTIMAX HE PLUS S Fehlerbehebungshandbuch

Ferroli

Ferroli MODENA 27CHE Technisches Handbuch

Ferroli

Ferroli Modena 102 Benutzerhandbuch

Ferroli

Ferroli PEGASUS 67-107 2S Bedienungsanleitung

Ferroli

Ferroli LG 14 Bedienungsanleitung

Ferroli

Ferroli BLUEHELIX B S 45 Fehlerbehebungshandbuch

Ferroli

Ferroli Domina 102 Benutzerhandbuch

Ferroli

Ferroli ATLAS D 30 K 100 UNIT Fehlerbehebungshandbuch

Ferroli

Ferroli MODENA 27 C HE Fehlerbehebungshandbuch

Ferroli

Ferroli DOMIcompact F 30 B Fehlerbehebungshandbuch

Ferroli

Ferroli OPTIMAX HE PLUS 25 S Fehlerbehebungshandbuch

Ferroli

Ferroli OPTIMAX HE 18 OV Fehlerbehebungshandbuch

Ferroli

Ferroli Divatop ST F 24 Technisches Handbuch

Ferroli

Ferroli BLUEHELIX TECH S 45H Fehlerbehebungshandbuch

Ferroli

Ferroli Falcon Benutzerhandbuch

Ferroli

Ferroli Optima 700 Technisches Handbuch

Ferroli

Ferroli Falcon II Benutzerhandbuch

Ferroli

Ferroli ATLAS D ECO COND UNIT Series Fehlerbehebungshandbuch

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Ferroli optima 801 Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken