Festo CPX-IOT Bedienungsanleitung

Translation of the original instructions

EtherNet/IP®, OPCUA®, PI PROFIBUS PROFINET®, SPEEDCON® are registered

trademarks of the respective trademark owners in certain countries.

1 Intended use

The module described in this document is intended for use in the industrial sector

as a gateway between industrial Ethernet networks and cloud applications, such

as, forexample, Festo Dashboard applications.

The module is intended for installation in machines or automation-technology

systems and may only be used only as follows:

– In perfect technical condition

– In its original condition, without unauthorised modifications, except for the

adaptations described in this document

– Within the limits of the product defined by the technical data.

Outside of industrial environments, e.g.in commercial and mixed-residential

areas, it may be necessary to take measures to suppress interference.

Information on commissioning and operating the gateway, e.g. to activate the

network connections "Cloud" and "Device" and to integrate them into the cloud

("Onboarding"):

è 6.3 Rotary switch operating mode

èFesto App World, www.festo.com/appworld

èFesto Dashboards, dashboards.festo.com

Information on the terminal CPX:

èSystem description of the terminal CPX (CPX-SYS), www.festo.com/pk

All available documents for the product èwww.festo.com/pk.

Note on licencing

This product uses open-source software, which is subject to "GNU General Public

License", Version2 and "GNU Lesser General Public License",

Version2.1,among others.

The licence conditions of the GPL, LGPL and the other open-source licences can be

viewed via the integrated web server of the product:

• Connect the gateway via the network connection "Device" with a PC or Note-

book.

• Calling up the web server:

èhttp://<IP-Adresse_des_Netzwerkanschlusses_"Device"/cgi-bin/system-

about.

2 Safety

– Before assembly or installation work:

Switch off the power supply and secure it against being switched on again.

– For the electrical power supply, use PELV circuits in accordance with

IEC 60204-1/EN 60204-1.

– Observe the handling specifications for electrostatically sensitive devices.

– Seal unused connections with cover caps to achieve the required degree of

protection.

– Use connection hardware with the required degree of protection.

– Observe specifications in the system description of the terminal CPX

(CPX-SYS).

– Commission only a completely mounted and wired module.

3 Connection and display components

1LED displays

2Network connection "Cloud"

3Network connection "Device"

4Rotary switch operating mode

5DIL switch

6Interface to the terminal CPX

without a network connection

è 8 Connection technology

Fig. 1 Connection and display components

3.1 Network connections

For connection to the Internet and the local industrial Ethernet network or direct

connection to the field devices, there are two industrial Ethernet interfaces on the

module, the network connections "Cloud" and "Device". Both connections have

Auto-Negotiation und Crossover detection (factory setting).

Cloud2) Device2)

Connection

Signal3) Explanation Signal Explanation

1 TD+ Transmitted data + RD+ Received data +

2 RD+ Received data + TD+ Transmitted data +

3 TD– Transmitted data – RD– Received data –

4 RD– Received data – TD– Transmitted data –

Housing,

shielding con-

nected4)

FE,

Shield

Functional earth5) FE,

Shield

Functional earth5)

1) socket, M12, D-coded, 4-pin, SPEEDCON-compatible

2) Pin activation with deactivated crossover detection

3) TD = Transmit Data, RD = Receive Data, FE = Functional Earth

4) via RC link to functional earth

5) equipotential bonding èSystem description of the terminal CPX (CPX-SYS)

Tab. 1 Network connections

3.1.1 Fieldbus protocol and field devices

Via the network connection "Device", field devices can be directly connected with

an industrial Ethernet connection to the Gateway, e.g. bus node or controllers

(controller, PLC) with protocols such as, forexample, PROFINET, EtherNet/IP or

OPCUA.

Information on the supported field devices and controllers èFesto AppWorld,

www.festo.com/appworld.

3.1.2 Network security

NOTICE!

Unauthorised access to the device can cause damage or malfunctions.

When connecting the device to a network, protect the network from unauthorised

access.

Measures to protect the network include:

• Firewall

• Intrusion Prevention System (IPS)

• Network segmentation

• Virtual LAN (VLAN)

• Virtual Private Network (VPN)

• Security at physical access level (Port Security)

An access password only protects against unintentional modification.

For additional information èGuidelines and standards for security in information

technology, e.g. IEC62443, ISO/IEC27001.

When connecting the gateway, configure the firewall setting for the network con-

nection "Cloud" as follows:

– Outgoing connections: release for port 443 (HTTPS)

– Incoming connections: no port release

For further information on the required measures in terms of network security,

enter èwww.festo.com/sp: "CPX-IOT", filter according to Application Note .

8108871

CPX-IOT

Gateway

8108871

2019-04a

[8108873]

Instructions| Operating

Festo AG & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

3.2 LED displays

Network-specific LED displays Gateway-specific LED displays

Cloud

(blue)

Network status "Cloud" PS

(green)1)

Status of operating voltage -

supply

(Power System)

(red/green)

Network status "Device"2) PL Reserved

TP1

(green)

Connection status "Cloud"

("Link/Traffic")

(red)1)

System error

(System Failure)

TP2

(green)

Connection status "Device"

("Link/Traffic")2)

(yellow)

Module status "Onboarding"

1) General information on the LEDs PS and SF èSystem description of the terminal CPX (CPX-SYS)

2) Module positioning: LEDs PS, PL and NS flash at the same rate.

Tab. 2 LED displays

Normal operating status

Behaviour of the LED displays in a normal operating status:

– PS and NS illuminated green

– Cloud illuminated blue

– TP1 and/or TP2 illuminated or flashing green

– PL, SF and M are not illuminated

3.2.1 Network status "Cloud"

LED status Meaning Error handling

Illumin-

ated blue

Normal operating status:

Network connection to the cloud

("Link") created

–

Flashes

blue 1x

Creation or new creation of a con-

nection to the cloud

–

Flashes

blue 2x

Network error – Check the configuration, e.g.

DHCP address assignment,

static IP address

Off

No connection to the cloud – Check network connection

Tab. 3 Network status "Cloud" (LED with cloud symbol)

3.2.2 Network status "Device" (Network Status)

LED status Meaning Error handling

Illumin-

ated

green

Normal operating status:

The gateway is connected with field

devices ("Devices").

–

Flashes

green

No connection to field devices

("Devices"):

The gateway is online and has an IP

address, but is not yet connected

with field devices.

– Check configuration

– Check module status

– Restart module ("Reboot")

– Repeat "Onboarding"

Illumin-

ated red

Communication with the field

devices("Devices") has failed:

Non-permitted network configura-

tion, e.g. already used IP address.

– Check configuration, e.g.

DHCP address assignment,

static IP address

Flashes

red

Communication with field devices

has failed:

Network connection disturbed, z.B.

connecting cable interrupted.

– Check device connection

Off

The gateway is offline. – Check network connection

Tab. 4 Network status "Device" (Network Status, LED NS)

3.2.3 Module status "Onboarding"

LED status Meaning Error handling

Off

Normal operating status:

Onboarding completed.

The gateway has been successfully

integrated into the cloud applica-

tion.

The gateway is in the operating

mode "Off", "Read only" or

"Read/Write"

è 6.3 Rotary switch operating

mode.

–

Flashes

yellow 1x

Gateway Onboarding active:

The gateway is in operating mode

"Onboarding".

The gateway is integrated into the

cloud application.

–

Flashes 2x

yellow

The gateway is in operating mode

"Onboarding".

The gateway has been successfully

integrated into the cloud applica-

tion.

– Select operating mode

"Read only" or "Read/Write"

è 6.3 Rotary switch operating

mode

Flashes 3x

yellow

Devices Onboarding active.

The gateway performs a network

scan: supported devices

("Devices") are integrated into the

cloud application.

The gateway is in operating mode

"Read/Write".

–

Illumin-

ated yel-

low

The gateway is not yet integrated

into the cloud application.

The gateway is in the operating

mode "Off", "Read only" or

"Read/Write"

è 6.3 Rotary switch operating

mode.

– Perform Onboarding

Tab. 5 Module status "Onboarding" (LED M)

3.2.4 Connection status "Cloud"

LED status Meaning Error handling

Illumin-

ated

green

Normal operating status:

Network connection to the cloud

established

–

Flashes

green

Data traffic ("Traffic")1) –

Off

No network connection – Check network connection

1) Flashing frequency is dependent on the traffic.

Tab. 6 Connection status "Cloud" (Link/Traffic, LED TP1)

3.2.5 Connection status "Device"

LED status Meaning Error handling

Illumin-

ated

green

Normal operating status:

Network connection ("Link") to the

field devices ("Devices") estab-

lished

–

Flashes

green

Data traffic ("Traffic")1) –

Off

No network connection – Check network connection

1) Flashing frequency is dependent on the traffic.

Tab. 7 Connection status "Device" ("Link/Traffic", LED TP2)

3.2.6 Status of operating voltage supply (Power System)

LED status Meaning Error handling1)

Illumin-

ated

green

Normal operating status:

Operating voltage applied.

–

Flashes

green

Undervoltage:

Operating voltage outside the toler-

ance range.

– Rectify undervoltage.

Off

Operating voltage is not present – Check operating voltage sup-

ply

1) General information on LEDPS èSystem description of terminalCPX (CPX-SYS)

Tab. 8 Status of operating voltage supply (Power System, LED PS)

3.2.7 System error (System Failure)

LED

(red)

Process

Meaning Error handling2)

Off

Normal operating status:

No error.

–

Flashes

red 1x

Simple error / information

(error class 1)3)

Flashes

red 2x

Error

(error class 2)4)

Flashes

red 3x

Serious error, internal error, e.g.

hardware error

(error class 3)5)

– Error handling

èFesto App World,

www.festo.com/appworld.

1) The LED SF flashes if an error occurs and is dependent on the error class.

2) General information on LEDSF èSystem description of the terminalCPX (CPX-SYS)

3) Error class1 (minor error): 1xflash, pause

4) Error class2 (error): 2xflashes, pause

5) Error class3 (serious error): 3xflashes, pause

Tab. 9 System error (System Failure, LED SF)

4 Assembly and disassembly

The module must be inserted into an interlinking block for the terminal CPX

èwww.festo.com/catalogue:

– Version 1:

Gateway in an interlinking block with system supply, e.g.CPX-GE-EV-S-...,

between two end plates

– Version 2:

Gateway in an interlinking block without supply, between two end plates with

system supply, e.g.CPX-EPL-EV-S-...

Information on power supply è 5 Power supply.

1Gateway CPX-IOT

2Screw

3Interlinking block

(with system supply)

Fig. 2 Assembly and disassembly

4.1 Assembly

NOTICE!

Material damage due to incorrect mounting.

Select screws that are suitable for the material of the interlinking block:

• Polymer: thread-grooving screws

• Metal: screws with metric thread

When ordering an individual module, all the screws required are enclosed.

1. Switch off the power supply and secure it against being switched on again.

2. Check seal and seal surfaces. Replace damaged parts.

3. Push the module carefully and without tilting into the interlinking block up to

the stop.

4. Turn the screws into the existing thread.

5. Tighten the screws in diagonally opposite sequence.

Tightening torque:1Nm ±10%.

4.2 Disassembly

1. Switch off the power supply and secure it against being switched on again.

2. Unscrew the screws.

3. Pull the module without tilting out of the interlinking block.

5 Power supply

The operating and load voltage supply is fed in via interlinking blocks or end

plates with system supply.

Information on power supply:

èSystem description of the terminal CPX (CPX-SYS)

èPin allocation power supply connection (CPX-PIN-BEL)

WARNING!

Risk of injury due to electric shock.

• For the electric power supply, use PELV circuits that guarantee a reliable elec-

tric disconnection from the mains network.

• Observe IEC 60204-1/EN 60204-1.

• Connect all circuits for the operating and load voltage supply.

6 Switching elements

1DIL switch 1

2DIL switch 2

3Rotary switch operating mode

Fig. 3 Switching elements

6.1 DIL switch 1

Switching position Function

DIL 1.1: Off

(factory setting)

Reserved

DIL 1.1: On Reserved

Tab. 10 DIL switch 1.1

Switching position Function

DIL 1.2: Off

(factory setting)

Reserved

DIL 1.2: On Reserved

Tab. 11 DIL switch 1.2

6.2 DIL switch 2

Switching position Function

DIL 2.1: Off

(factory setting)

Reserved

DIL 2.1: On è 10 Reset to factory setting ("FactoryReset")

Tab. 12 DIL switch 2.1

Switching position Function

DIL 2.2: Off

(factory setting)

Reserved

DIL 2.2: On è 10 Reset to factory setting ("FactoryReset")

Tab. 13 DIL switch 2.2

6.3 Rotary switch operating mode

Switching position Operating mode/function

0: Off – Network connection "Cloud" deactivated (switch-off of inter-

face)

– No communication with the cloud

1: Onboarding – Network connection "Cloud" activated

– Gateway for integration into the cloud ("Onboarding") ready

2: Readonly – Gateway sends process data of the configured field devices to

the cloud

– Manual adding of field devices enabled

– Automatic adding of field devices via the Auto-Scan function

blocked

– Removal of field devices and removal of the gateway from the

cloud ("Offboarding") blocked

– Receipt of data, e.g. parameters, from the cloud disabled

– Parameters of connected devices cannot be changed

3: Read/Write – Gateway sends process data of the configured field devices to

the cloud

– Manual adding of field devices enabled

– Automatic adding of field devices via the Auto-Scan function

enabled

– Removal of field devices and removal of the gateway from the

cloud ("Offboarding") enabled

– Receipt of data, e.g. parameters, from the cloud enabled

– Parameters of connected devices can be changed

Tab. 14 Rotary switch operating mode

7 Ensuring the degree of protection

NOTICE!

Short circuit as a result of ingress of liquids or foreign matter.

Malfunction or damage to the electronics.

• Use connection devices (connecting cables, plugs, adapters) with the

required degree of protection.

• Use cover caps to seal unused connections.

• Mount the DIL switch cover:

– Check the seal.

– Place cover and press it on.

– Tighten screws.

Tightening torque: maximum0.4Nm.

8 Connection technology

Using the M12 socket 6 (è Fig.1), a terminal CPX can be directly connected with

the gateway without a network connection, i.e. without an industrial Ethernet

connection.

Connection Connecting hardware Cover cap

Network connection "Cloud"1)

Network connection "Device"1)

Plug NECU-M-S-D12G4-C2-ET

Interface to terminal CPX

without a network connection2)

Connecting cable

NEBC-M12G5-S-1,5-N-M12G5

ISK-M12

1) socket, M12, D-coded, 4-pin, SPEEDCON-compatible

2) socket, M12, A-coded, 5-pin

Tab. 15 Connection technology

9 Parameterisation

The gateway can be parameterised via the FestoField Device Tool (FFT).

Alternatively, the integrated web server of the gateway can be used via the net-

work connection "Device" for the parameterisation, e.g. for setting the IP

addresses of the network connections:

Connect the gateway via the network connection "Device" with a PC or Notebook.

Calling up the web server:

èhttp://<IP-Adresse_des_Netzwerkanschlusses_"Device"> (see IP configuration

(factory settings) è 13 Technical data)

Logging in:

èUser name: admin

èPassword (factory setting): CPX-IoT Product Key on the type plate, e.g.

3S7PMM2M93V

10 Reset to factory setting ("FactoryReset")

1. Set rotary switch to "Off".

2. Switch off the power supply.

3. Set DIL switch 2.1 and 2.2 to "On".

4. Switch on the power supply.

ÄLEDM flashes quickly for a few seconds.

– Do not switch off the power supply

– Do not actuate the DIL switch

5. If the LEDM has stopped flashing:

Set DIL switch 2.1 and 2.2 to "Off".

ÄThe gateway has returned to the factory setting.

11 Firmware update

A firmware update is possible via the Festo Field Device Tool (FFT)

èwww.festo.com/sp.

12 Module replacement

After replacing a gateway, integration into the cloud („Onboarding“) must be car-

ried out again èFesto App World, www.festo.com/appworld.

13 Technical data

Property Specification/value

General technical data èSystem description of the

terminal CPX (CPX-SYS)

Power supply

Operating power supply UEL/SEN [VDC] 24 ±25%

Intrinsic current consumption at nominal operat-

ing voltage 24V from operating voltage supply

UEL/SEN

[mA] Typically 80

(internal electronics)

Mains buffering time [ms] 10

Separation of network interface from operating

voltage supply UEL/SEN

Galvanic

Protection against electric shock1) Through the use of PELV circuits

Degree of protection by housing2)3),

With power supply connection

– Via interlinking block IP65/IP67

– Via end plate IP20

Connection technology

Network connections 2 × sockets, M12, D-coded, 4-pin,

SPEEDCON-compatible

Interface to terminal CPX

without a network connection

1 × socket, M12, A-coded, 5-pin

Network-specific characteristics

Cloud DHCP IP configuration (factory settings)

Device IP address: 192.168.0.1

Subnet mask: 255.255.255.0

Encryption of data transmission to the Cloud HTTPS

Transmission technology Industrial Ethernet,

Switched Fast Ethernet

Specification IEEE 802.3u (100Base-TX)

Transmission rate [Mbit/s] 10/100 (full duplex/half duplex)

Crossover detection Auto-MDI/MDI-X

Number of devices (network connection

"Device")

Maximum 104)

Cable specification

Cable type Ethernet twisted pair cable, shiel-

ded (Shielded Twisted Pair, STP)

Transmission class (Link Class) Category Cat 5

Cable diameter5) [mm] 6…8

Wire cross section6) [mm2] 0.14…0.75

Cable length [m] Maximum 100

1) protection against direct and indirect contact in accordance with IEC60204-1/EN60204-1

2) Degree of protection in accordance with IEC60529, module completely assembled, plug connector in the

plugged-in status or provided with cover cap

3) Connected products may only fulfil a lower degree of protection.

4) More devices can be operated depending on the application.

5) when using the plug NECU-M-S-D12G4-C2-ET

6) 22AWG required for max. connection length between network participants (end-to-end link)

Tab. 16 Technical data

14 Specified standards

Version

IEC 60529:2001-02 IEEE 802.3:2014-00

Tab. 17 Specified standards

Andere Festo Tor Handbücher

Festo

Festo CESA-GW-AS-CO Bedienungsanleitung

Festo

Festo CPX-IOT Bedienungsanleitung

Festo

Festo CESA-GW-AS-PB Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung