Festo CASB-MT-D3-R7 Bedienungsanleitung

Translation of the original instructions

1 Further applicable documents

All available documents for the product èwww.festo.com/pk.

Observe further applicable documents:

– Instruction manual for cylinder DNCI-...-BA

2 Intended use

– Conversion of sensor signals from cylinder DNCI-...-BA into an HTL signal and

a differential TTL signal.

– Connection option for making further use of the raw signal from a displace-

ment encoder of cylinder DNCI-...-BA for control or measurement applications.

3 Further information

– Accessories èwww.festo.com/catalogue.

4 Product overview

4.1 Product range overview

4.1.1 Included in delivery

1Sensor interface (1x)

Fig. 1 CASB-MT-D3-R7

4.1.2 Not included in the delivery

2Screw (4x)

Fig. 2 Retaining screws

4.2 Connecting components

AConnection socket DNCI-...-BA

Sensor 1

BConnector plug for safety relay unit

for TTL signals

CConnector plug for safety relay unit

for HTL signals

DConnection socket DNCI-...-BA

Sensor 2

EConnector plug VPCB-...-T22

Valve unit

FEarth connection

Fig. 3 Connecting component

5 Wall mounting

Fig. 4

1. Select screws2 select screws suitable for the installation situation.

2. Prepare the thread[G] on the mounting surface.

3. Mount the sensor interface1 via the slotted holes[H] using screws2 in the

threads[G]. Tightening torque: £3Nm

6 Electrical installation

6.1 Safety

WARNING!

Risk of injury due to electric shock.

• For the electrical power supply, use only PELV circuits in accordance with IEC

60204-1/EN 60204-1 (Protective Extra-Low Voltage, PELV).

• Observe the general requirements of IEC 60204-1/EN60204-1 for PELV cir-

cuits.

• Only use voltage sources that ensure a reliable electric separation from the

mains network in accordance with IEC 60204-1/EN 60204-1.

NOTICE!

Malfunction due to electromagnetic interference.

Incorrect measuring results and incorrectly stated positions.

• Use permitted lines without extensions.

• Lay permitted lines with sufficient clearance from lines with high noise level.

• Connect the earth terminal with low impedance to the earth potential.

6.2 Contact assignment

Socket [A], socket [D] M12, 8-pin

Connection sensor1,

sensor2

Pin Signal

1 5V DC

2 0V

3 Sin +

4 Sin –

5 Cos –

6 Cos +

7 Shield

8 n.c.

Tab. 1 Contact assignment sensor 1, sensor 2

Plug[B] M12, 8-pin

Connection TTL Pin Signal

1 n.c.

2 0V

3 A+

4 A–

5 B+

6 B–

7 n.c.

8 24V DC

Tab. 2 Contact assignment TTL

8084103

CASB-MT-D3-R7

Sensor interface

8084103

2018-07

[8084105]

Instructions| Assembly| Installation

Festo AG & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Plug [C] M12, 5-pin

Connection HTL Pin Signal

1 A

2 B

3 24V DC

4 0V

5 n.c.

Tab. 3 Contact assignment HTL

Plug [E] M12, 8-pin

Connection VPCB Pin Signal

1 5V DC

2 0V

3 Sin +

4 Sin –

5 Cos –

6 Cos +

7 Shield

8 n.c.

Tab. 4 Contact assignment VPCB

6.3 Assembly of electrical connections

1. Use permitted lines:

Connecting component Line Cable length [m]

[A], [D] Sensor1, sensor2 Integrated in the displace-

ment encoder of cylinder

DNCI-...-BA

£1.5

[B] TTL NEBU-M12W8-... £10

[C] HTL NEBU-M12G5-... £10

[E] VPCB KM12-8GD8GD-2-PU £2

Tab. 5 Permitted lines

2. Connect matching plugs to the sockets[A] and [D]. Tightening

torque:0.4Nm±10%

3. Connect matching sockets to the plugs[B], [C] and [E]. Tightening

torque:0.4Nm±10%

6.4 Assembling the earthing cable

Fig. 5 Assembling the earthing cable

1. Undo screw[J] and toothed disc[K] from the sensor interface1.

2. Place cable lug[L] of the earthing cable between the screw[J] and the toothed

disc[K].

3. Tighten the screw[J]. Tightening torque: 1Nm±10%

7 Malfunctions

7.1 Diagnostics

LED TTL LED HTL Status

Off Off 24VDC not present

Off On Valve VPCB not connected

On Off 24VDC not present at HTL

On On Ready for operation

Tab. 6 Diagnostics

8 Technical data

CASB-MT-D3-R7

Reverse polarity protection Yes

Output frequency, HTL signal [Hz] £ 450

Output frequency, TTL signal [Hz] £ 7200

Nominal operating voltage DC [V] 24

Requirement on the power supply PELV

Residual ripple 5%

Current consumption with load-free outputs [mA] 50

Current rating per output [mA] 50

CE marking (see declaration of conformity):

èwww.festo.com/sp

To EU EMC Directive1)

KC Mark KC EMC

Degree of protection

Degree of protection IP65

Note on degree of protection In assembled state

Signal range, HTL signal

High [V] ³ 18

Low [V] £ 2

Signal range, TTL signal

High [V] ³ 2.4

Low [V] £ 0.4

1) The product is suitable for industrial purposes only. Measures for interference suppression may be

required in residential areas.

Tab. 7 Technical data CASB-MT-D3-R7

Dieses Handbuch passt für folgende Modelle

Andere Festo Aufnahmegeräte Handbücher

Festo

Festo CPX-AP-I-PN-M12 Stücklistenhandbuch

Festo

Festo CPX-AP-I-PB-M12 Stücklistenhandbuch

Festo

Festo VAEM-L1-S-12-AP Bedienungsanleitung

Festo

Festo CPX-CTEL-4-M12-5POL Bedienungs- und Montageanleitung

Festo

Festo CAMC-D-8E8A Bedienungsanleitung

Festo

Festo CPX-AP-I-EP-M12 Stücklistenhandbuch

Festo

Festo CAMC-D-8E8A Bedienungsanleitung

Festo

Festo CPX-CP-4-FB Stücklistenhandbuch

Festo

Festo CPX-CTEL-2-M12-5POL-LK Bedienungsanleitung

Festo

Festo CMMS-ST Bedienungs- und Montageanleitung

Festo

Festo CPX-CTEL-2-M12-5POL-LK Bedienungs- und Montageanleitung

Festo

Festo CAMC-D-8E8A Bedienungsanleitung

Festo

Festo CPX Series Stücklistenhandbuch

Festo

Festo CPX-FB13 Bedienungsanleitung

Festo

Festo CAMC-D-8E8A Bedienungsanleitung

Festo

Festo PROFINET CPX-AP-A-PN-M12 Bedienungsanleitung

Festo

Festo CPX-AP-A-EP-M12 Bedienungsanleitung

Festo

Festo CPX-AP-I-EC-M12 Bedienungsanleitung

Festo

Festo CPX-CP-4-FB Stücklistenhandbuch

Festo

Festo CPX-CP-4-FB Schulungshandbuch

Festo

Festo SPC-AIF-MTS-2 Bedienungsanleitung

Festo

Festo VMPAL-EPL-AP Bedienungsanleitung

Festo

Festo CPV10-GE-DI01-8 Bedienungsanleitung

Festo

Festo CAMC-D-8E8A Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch