FFE TalentumTT2 Bedienungsanleitung

Page 1
User Guide
EN
Document No: 0044-117-01
www.ffeuk.com

Page 2
Contents
1. The TalentumTT2
Features
2. Specification
Light Source Performance
Operational Environment
Environmental & Personal Protection
3. Safety Warnings
4. Equipment
5. Charging the TalentumTT2
6. Maintaining the TalentumTT2
7. Introducing the TalentumTT2
8. Testing a Talentum Flame Detector
Setting up a Talentum Flame Detector Test
Testing an IR2 or IR3 Talentum
Testing a UV/IR Talentum
9. Recalibrating a Talentum Flame Detector
Calibration Errors
10. Test Data Log
11. Open Source Software Agreement
p.3
p.3
p.4
p.4
p.4
p.4
p.5-6
p.7
p.8
p.9
p.10-13
p.14
p.15-16
p.17
p.18-21
p.22-24
p.25
p.26

Page 3
1. TalentumTT2Overview
Features
This user guide describes the proper use of the FFE TalentumTT2, which is intended to
• Precisely simulate a real flame’s spectral emissions to test that a Talentum Flame Detector is responsive to the presence of a flame.
• Calibrate a Talentum Flame Detector to be appropriately sensitive to the presence of a flame.
• Flame Detector Test
• Test both IR and UV/IR Flame Detector Models
• Tests installed Flame Detectors up to 8m away
• Designed to simulate a real fire, not the sun or artificial light
•Broad-spectrum test: UV, visible, near IR, Mid IR frequencies
•Flickering multi-spectral output
•Solar spectrum profile not present in the output
• Flame Detector Re-Calibration
• If a Flame Detector fails a test, it can be recalibrated on-site, you will need a Calibration Kit to do so
• Flame Detectors can be recalibrated in-situ or dismounted if required
• Test and Calibration Data
• The TalentumTT2Unit stores data on tests and calibrations
• Data can be retrieved via USB interface and sent to FFE Support
• FFE Support can use the data to aid in specific support enquires and product improvement
• Portable hand-held torch body with convenient USB charging

Page 4
Light Source Performance
2. Specification
Light Source Power 1x20W
2x10W
Spectral
Response
UV
Visible
Near IR Mid IR
200nm
to
4.3µm
Test Range 1 - 8m
Typical
Recharge Time Around 2.5 Hours
Duty Cycle (IR-Only) 40 x 30-Second Tests (approx.)
Duty Cycle (UV/IR) 30 x 30-Second Tests (approx.)
Battery Performance
Operational Environment
Operating Temperature -10°C to +55°C
Hazardous (Ex) Areas Not suitable for use in
hazardous areas
IP Rating IP54
Recycle raw materials instead of disposing of
them as waste.
The unit, accessories, and packaging should be
sorted for environmentally friendly recycling.
This product emits IR, visible, UV-A, UV-B &
UV-C radiation. Care should be taken to avoid
pointing the light emitted at people, animals, or
sensitive equipment.
Environmental & Personal Protection

Page 5
3. Safety Warnings
Per the Talentum User Guide, users should conduct regular maintenance and testing of Talentum fire detection products according to the risk
and environment in which the product(s) are located. The frequency of such maintenance and test schedule should be revisited at regular
intervals to ensure that it remains appropriate.
Please be aware that the TalentumTT2does not have an (Ex) approval for hazardous areas. A permit is required to test a detector in such
areas. Alternatively, the Flame Detector should be removed and placed within a safe location to perform the test.
Testing of a Flame Detector should only be conducted where it is safe to do so and by personnel with appropriate training and equipment.
Ultraviolet radiation may cause harm. Please avoid any direct exposure to eyes and skin when using the TalentumTT2
This device contains lithium-ion batteries that are not replaceable by the user; the following care should be taken:
• Do not disassemble or allow any intrusion into the case.
• Keep dry, do not immerse in liquid.
• Do not charge on a flammable surface or in an explosive environment.
The FFE TalentumTT2has been designed to work specifically with Talentum Flame Detectors. FFE cannot guarantee the capability to
accurately test other manufacturers’ Flame Detectors.

Page 6
The TalentumTT2is only intended for use with the following devices.
• 16581 IR2 Flame Detector
• 16571 IR2 Flame Detector - Intrinsically safe (IS)
• 16511 IR2 Flame Detector - Flameproof (Exd)
• 16501 IR2 Flame Detector - Stainless steel
• 16541 IR2 Flame Detector - Stainless steel flameproof (Exd)
• 16589 IR3 Flame Detector
• 16579 IR3 Flame Detector - Intrinsically safe (IS)
• 16519 IR3 Flame Detector - Flameproof (Exd)
• 16509 IR3 Flame Detector - Stainless Steel
• 16549 IR3 Flame Detector - Stainless steel flameproof (Exd)
• 16591 UV/IR2 Flame Detector
• 16521 UV/IR2 Flame Detector - Flameproof (Exd)
• 16531 UV/IR2 Flame Detector - Stainless Steel
• 16561 UV/IR2 Flame Detector - Stainless Steel, Flameproof (Exd)
Note: The FFE TalentumTT2is not rated for use in Hazardous areas. Intrincially Safe and Exd devices should be moved to a safe area when
using the product.

Page 7
4. Equipment
Task Required Equipment Recommended Equipment Note
Testing a
Talentum
A Test Unit (Supplied) -IR only and UV/IR testing require only equip-
ment supplied in the kit.
Recalibrating a
Talentum
A Test Unit (Supplied)
A Calibration Kit (Supplied separately,
Contact FFE to order).
-The Calibration Kit (Supplied separately,
Contact FFE to order) includes a Shroud and
a Calibration Cable. May be able to bring older
Talentum units back into normal operation if
they have drifted out of calibration and no longer
indicate a fire when tested with a TalentumTT2.
Charging Test
Torch
USB data and charging cable (Supplied).
Any USB-A (standard) charging port such
as a USB mains charger
(Not Supplied).
USB data and charging cable (Supplied).
A Fast Charge capable USB-A (standard)
charging port such as a Fast Charge USB
mains charger (Not Supplied).
A mains charger is not supplied. Use the USB
data and charging cable supplied.
Reading Test
Torch Logs
USB data and charging cable (Supplied).
Any computer, tablet or other device
(Not Supplied) that supports reading
from USB hard drives with a USB-A
(standard) data port of any speed (USB
1.1+).
USB data and charging cable (Supplied).
Any computer, tablet or other device
(Not Supplied) that supports reading
from USB hard drives with a USB-A
(standard) data port with USB 2.0+
speed.
Reading the logs is not needed for normal
operation. Use the USB data and charging cable
supplied to connect the torch to your PC.

Page 8
5. Charging the TalentumTT2
The TalentumTT2uses lithium-ion batteries that must be charged by plugging the USB cable into the USB-C port of the unit and
connecting the other end to a Fast Charge capable USB socket.
The LED next to the USB-C connector will be solid green while the TalentumTT2is charging, turns off when charging is complete and
will flash if the battery is unable to charge due to a fault. In case of a fault, try an alternative charger and if it is not possible to charge the
TalentumTT2, return it for service.

Page 9
6. Maintaining the TalentumTT2
• Charge regularly and avoid leaving with a low battery.
• Check for significant damage or soiling before use; discontinue use if the item is more than cosmetically damaged or soiled.
• Check the USB cable for damage before use, replace with Fast Charge and data transfer compatible USB-A male to USB-C male
cable if required.
• Do not disassemble the TalentumTT2.
• Do not use liquids or abrasives to clean the TalentumTT2.

Page 10
The TalentumTT2user interface consists of an LCD screen and seven control buttons, as illustrated below:
7. Introducing the TalentumTT2
Power Button
OK Button
Direction Buttons
Up, Down, Left, Right
Getting to know your TalentumTT2
Back Button
Trigger Button: Indicated
on screen with ‘+’
USB Port Charging Light
Inhaltsverzeichnis
Andere FFE Sicherheitssensor Handbücher


















