FIBARO WALLI FGWCEU-201 Bedienungsanleitung
FIBARO WALLI CONTROLLER
FGWCEU-201
OPERATING
MANUAL EN
v1.1
3
Table of contents
1: Important safety information 4
2: Description and features 5
2.1: Description 5
2.2: Main features 5
3: Specications 6
4: First installation 7
4.1: Installing on a smooth surface with battery supply 7
4.2: Installing on a mounting box with battery supply 7
4.3: Installing on a mounting box with an external power supply 8
5: Adding to Z-Wave network 9
5.1: Adding manually 9
5.2: Adding using SmartStart 10
6: Removing from Z-Wave network 11
7: Operation 12
7.1: Controls 12
7.2: Operating modes 12
7.3: Powering modes 14
7.4: Temperature sensor 15
7.5: Waking up 15
7.6: Visual indications 15
7.7: Menu 16
7.8: Resetting to factory defaults 17
8: Conguration 18
8.1: Associations 18
8.2: Advanced parameters 21
9: Z-Wave specication 24
10: Regulations 27
4
Important safety InformatIon
1: Important safety information
Read this manual before attempting to install the device!
!Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manu-
facturer, Fibar Group S.A. will not be held responsible for any loss or
damage resulting from not following the instructions of operating
manual.
CAUTION!
!Risk of Explosion if battery is replaced by an incorrect type. Dis-
pose of used batteries according to the instructions.
Do not modify!
!Do not modify this device in any way not included in this
manual.
This product is intended for indoor use only in dry locations.
!Do not use in damp or wet locations, near a bathtub, sink,
shower, swimming pool, or anywhere else where water or
moisture are present.
Not a toy!
!This product is not a toy. Keep away from children and
animals!
5
DescrIptIon anD features
2: Description and features
2.1: Description
FIBARO Walli Controller is a smart wall-mounted Z-Wave™ remote
controller that can activate scenes or control other Z-Wave devices
via associations.
2.2: Main features
• Can be used for controlling multiple types of devices, e.g. switch-
es, dimmers, roller shutters.
• Pre-set congurations allow to easily adjust operation for specic
type of controlled devices.
• Battery or VDC powered.
• Equipped with a built-in temperature sensor.
• Supports Z-Wave network Security Modes: S0 with AES-128 en-
cryption and S2 Authenticated with PRNG-based encryption.
• Works as a Z-Wave signal repeater when VDC powered (all
non-battery operated devices within the network will act as re-
peaters to increase reliability of the network).
• May be used with all devices certied with the Z-Wave Plus™ cer-
ticate and should be compatible with such devices produced by
other manufacturers.
The device is a Security Enabled Z-Wave Plus product and a
Security Enabled Z-Wave Controller must be used in order
to fully utilize the product.
i
6
specIfIcatIons
3: Specications
Power supply Battery and/or power supply unit
Battery type ER14250 ½AA 3.6V (included)
Supply unit type 5–24V DC SELV power supply, LPS or
NEC class 2 (not included)
Battery life est. 2 years (with default settings and
max. 10 pushes per day)
Operating temperature 0–40°C
Ambient humidity 0–90% RH without condensation
Radio protocol Z-Wave (700 series chip)
Radio frequency band 868.0–868.6MHz; 869.7–870.0MHz
Max. transmitting power +13dBm
Range up to 50m outdoors
up to 40m indoors
(depending on terrain and building
structure)
Dimensions
(Height x Width x Depth)
86 x 86 x 20 mm
Compliance with EU
directives
RoHS 2011/65/EU
RoHS 2015/863
RED 2014/53/EU
Radio frequency of individual device must be same as your
Z-Wave controller. Check information on the box or con-
sult your dealer if you are not sure.
i
7
fIrst InstallatIon
4: First installation
You can install the device on any smooth surface using included ad-
hesive tape or on a mounting box using screws.
The device will select the powering mode during adding to
the Z-Wave network, prioritizing external power supply if
connected. To change the mode after adding, you must re-
move it, change the installation accordingly, then add the
device again.
The device features a built-in temperature sensor, for ac-
curate temperature readings, install the device far from
sources of heat (e.g. radiators, power supplies).
Do not use the double-sided adhesive tape when mount-
ing the device on the electrical junction box.
4.1: Installing on a smooth surface with battery
supply
1. Remove the button cover.
2. Remove the paper strip protecting the battery.
3. LED ring light means the device is powered.
4. Insert the button cover back.
5. Remove the mounting frame from the device.
6. Use the included double-sided adhesive tape to stick the
mounting frame to the smooth and clean surface.
7. Push the device onto the mounting frame of the device, you
should hear an audible click.
4.2: Installing on a mounting box with battery
supply
1. Remove the mounting frame from the device.
2. Place the mounting frame onto the mounting box and secure it
with screws (*).
3. Push the device onto the mounting frame of the device, you
should hear an audible click.
4. Remove the button cover.
5. Remove the paper strip protecting the battery.
6. LED ring light means the device is powered.
7. Insert the button cover back.
i
i
i
8
fIrst InstallatIon
* To ensure no contact with electrical wires in the box, mount the
frame so that the power port is obscured by it.
4.3: Installing on a mounting box with an external
power supply
Prepare the power supply
1. Switch o the mains voltage (disable the fuse).
2. Using wire connectors, connect included power connector to the
power supply (black to negative wire, red to positive wire).
3. Using wire connectors, connect the power supply to the mains.
4. Place the power supply inside the mounting box, leaving the
power connector outside.
Assemble the device
5. Remove the mounting frame from the device.
6. Push the power connector through hole in the mounting frame.
7. Place the mounting frame onto the mounting box and secure it
with screws.
8. Plug the power connector into the device.
9. Push the device onto the mounting frame of the device, you
should hear an audible click.
10. Switch on the mains voltage.
11. LED ring light means the device is powered.
12. Remove the button cover.
13. Remove the paper strip protecting the battery if you want to use
it as emergency power source, remove the battery otherwise.
14. Insert the button cover back.
9
aDDIng to Z-Wave netWork
5: Adding to Z-Wave network
Adding (Inclusion) – Z-Wave device learning mode, allowing to add
the device to existing Z-Wave network.
The device will select the powering mode during adding to
the Z-Wave network, prioritizing external power supply if
connected. To change the mode after adding, you must re-
move it, change the installation accordingly, then add the
device again.
5.1: Adding manually
To add the device to the Z-Wave network manually:
1. Set the main controller in (Security/non-Security Mode) add
mode (see the controller’s manual).
2. Quickly, three times click one of the buttons.
3. If you are adding in Security S2 Authenticated, input the
underlined part of the DSK (label on the box).
4. LED will start blinking yellow, wait for the adding process to end.
5. Adding result will be conrmed by the Z-Wave controller’s
message and the LED frame:
• Green – successful (non-secure, S0, S2 non-authenticated),
• Magenta – successful (Security S2 Authenticated),
• Red – not successful.
i
10
aDDIng to Z-Wave netWork
5.2: Adding using SmartStart
SmartStart enabled products can be added into a Z-Wave network
by scanning the Z-Wave QR Code present on the product with a con-
troller providing SmartStart inclusion. SmartStart product will be
added automatically within 10 minutes of being switched on in the
network range.
To add the device to the Z-Wave network using SmartStart:
1. To use SmartStart your controller needs to support Security S2
(see the controller’s manual).
2. Enter the full DSK string code to your controller. If your controller
is capable of QR scanning, scan the QR code placed on the label
on the box.
3. Power the device.
4. Wait for the adding process to start (up to few minutes), which is
signalled with yellow LED blinking.
5. Adding result will be conrmed by the Z-Wave controller’s
message and the LED frame:
• Green – successful (non-secure, S0, S2 non-authenticated),
• Magenta – successful (Security S2 Authenticated),
• Red – not successful.
In case of problems with adding the device, please reset
the device and repeat the adding procedure.
i
Andere Handbücher für WALLI FGWCEU-201
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere FIBARO Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
