fieldSENSE fieldSENSE60 Bedienungsanleitung
1
ZH DEESFRITKRNLPTPT- BRRU EN
RF MONITOR OPERATION
Prior to entering an area where
transmitting antennas could be
present be sure to switch your
eldSENSE60 on.
Switch the eldSENSE60 on by
pressing and holding the Power
button for approximately 1 second.
The LEDs illuminate in sequence
followed by a BEEP. Once on, the
power indicator will ash.
Should the battery level be low, the
low battery indicator will illuminate.
Replace the batteries with AAA
alkaline batteries.
Should the exposure level rise above
50% an audible alarm is sounded.
DEVICE OVERVIEW
See technical gures on cover pages.
1. Impact resistant polycarbonate
base layer
2. Scratch & scuff resistant lens
3. Incident exposure indicator LED’s
4. Device Power On / Off indicator
5. Audio recording indicator
6. Low Battery indicator
7. Power / Record button
8. Strap harness attachment point
9. Device serial number and barcode
10. Heavy duty shock absorbing
elastomer outer layer
11. Lanyard attachment point
12. USB connection for data logging
(NOT FOR CHARGING)
13. Date Calibration Expires
14. Tripod attachment point
15. AAA Alkaline batteries (LR03)
16. Battery lid removal screws (M2)
ALWAYS ADHERE TO THE RELEVANT SAFETY REGULATIONS
PERTAINING TO RF EXPOSURE IN THE COUNTRY OF USE.
2
ZHDE ES FR IT KR NL PT PT-BR RUEN
When close to or exceeding 100%
of the exposure limit, the necessary
precautions need to be taken.
Once switched on the eld strength
data logger will record all eld
values measured every second.
These are accessible via the PC
application available from
www.eldsense.com.
Once the eldSENSE60 is on, the fall
detection & alarm system is armed
and in the event of a fall being
detected an alarm will sound which
can only be cleared by switching the
device off and on again.
To ensure that the device is not
inadvertently left switched on
causing unnecessary drain on the
batteries a timer will switch the unit
off after 8 hours.
EXPOSURE LOGGING
Once the eldSENSE60 is switched
on the cumulative exposure from all
sources present within the operating
frequency and exposure dynamic range
are stored as the Maximum, E and H
percentages with the associated date
and time thereof.
It is important to synchronize your
device time to your local time by
plugging it into a PC running the
FieldSENSE app available from
www.eldsense.com.
The reported and recorded values
are a percentage of the associated
exposure guideline power density,
either referenced to the E or H eld.
Data points are stored at up to once
every second in a changing eld. In
static eld conditions or below the
device noise oor less points are
stored to conserve memory.
A 6-minute average is also
calculated and stored.
Accessing these values and
synchronizing the date/time of
the device is achieved using the
FieldSENSE app available from
www.eldsense.com.
3
ZH DEESFRITKRNLPTPT- BRRU EN
VOICE NOTES
The eldSENSE60 can also capture
voice notes which are paired with the
measured data.
Once the device is on, double tap
the power button and the Audio
recording LED will illuminate.
Speak directly into the front of the
device slowly and clearly for best
performance.
A single short press of the power
button will end the audio recording
session, but the RF monitor remains on.
Voice notes can be downloaded
from the eldSENSE60 using the app
available from www.eldsense.com.
FALL DETECTION & ALARM
The eldSENSE60 is equipped with a
tri-axis accelerometer which is able to
detect if the device experiences a fall.
This is immediately activated
when the device is on, and should the
device detect a fall of approx. 2m
it will sound the alarm.
The alarm can only be cleared by
switching the device off.
This is to draw attention to a climber
who may be in need of support.
The alarm, if uncleared, will continue
until the batteries are exhausted.
REPLACING THE BATTERIES
When the Low Battery Indicator begins
to ash, replace the batteries.
It is NOT possible to charge the
device through the USB port, this is
exclusively for access to data and
voice logs.
Open the elastomer ap at the
bottom of the eldSENSE60
revealing the battery lid screws (16).
Remove the screws (16) and lid (14)
and slide out the old batteries (15).
Dispose of these correctly.
REMOVING THE BATTERIES FOR AN EXTENDED PERIOD OF TIME WILL
CAUSE THE DEVICE TO LOSE TIME ON THE INTERNAL CLOCK. THIS IS
CORRECTED BY PLUGGING IT INTO THE USB CONNECTION ON A PC
RUNNING THE FIELDSENSE APP.
4
ZHDE ES FR IT KR NL PT PT-BR RUEN
Insert 2 x new AAA (LR03) batteries
(15), paying attention to the polarity
thereof.
Replace the battery lid (14) and re-
tighten the screws (16).
Securely close the elastomer cover
to ensure the dust & moisture seal
remains intact.
HARNESS ATTACHMENT
Elastic strap
Insert the one end of the elastomer
strap through the strap harness
attachment bars (8) as shown in (17).
Pass the other end of the elastomer
strap around the webbing on the
harness you wish to attach it to.
Feed the other end of the elastomer
strap through the bars as above.
Pull on both ends until securely
fastened to the webbing.
Clip & coiled lanyard
Attach the coiled lanyard to the
lanyard attachment point (11) on the
eldSENSE60.
Pass the other end of the coiled
lanyard through the harness clip
mechanism as shown in (19), pulling it
back to clip in place as shown in (20).
Set the rear clip section behind the
webbing you wish to attach to and
press the front clip section rmly
into it until both ends clip (21).
The eldSENSE60 can now be
pressed into the clip and easily
removed as needed with a single
handed operation.
Inhaltsverzeichnis
