Filix Arpool XM Bedienungsanleitung
ARPOOL XM PROJECTOR
INSTALLATION INSTRUCTIONS (FIXTURE)
All dimensions are given according to the SI system of units (mm, kg, °C), additional dimensions that are written in brackets,
are given according to the U.S. measurement system (in, lbs, °F)
UNDERWATER
5m MAX.
Ta I 40°C
22
IP68 AISI316L12 VDC
GENERAL REMARKS ON SAFETY
·READ ALL OF THESE INSTRUCTIONS BEFORE INSTALLING
FIXTURES.
·KEEP ALL OF THE INSTRUCTIONS FOR FUTURE
REFERENCE.
·INSTALLATION IS TO BE PERFORMED BY A QUALIFIED
ELECTRICIAN ONLY.
·ALL INSTALLATIONS ARE TO CONFORM TO THE
STANDARDS OF THE NATIONAL ELECTRICAL CODE AS
WELL AS ALL LOCAL JURISDICTIONAL CODES AND
REGULATIONS.
·PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH
THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
·TURN OFF POWER BEFORE INSTALLING FIXTURE.
·DO NOT OPEN THE LUMINAIRE AS IT WILL ANNUL THE IP
RATING OF LUMINAIRE AND VOID THE WARRANTY.
·THE SURFACE TEMPERATURE OF THE FIXTURE IS ≈40°C
(104°F) AND IMPOSES NO LIMITS ON INSTALLATION.
·CALCULATE THE MAXIMUM POWER CONSUMPTION AND
USE APPROPRIATELY SIZED DRIVERS/CONTROLLERS.
·FIXTURES' SURFACES EXPOSED TO THE EFFECTS OF
WATER (INCLUDING WATER CONTAINING CHLORINE) ARE
MADE OUT OF AISI316L STAINLESS STEEL. AISI316L IS
SUITABLE FOR THIS USE AND WILL PREVENT CORROSION
UP TO LEVEL OF 1000 PPM OF CHLORINE IN WATER AND
UP TO WATER pH LEVEL OF 7.
·THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS
LUMINAIRE CANNOT BE REPLACED; IF THE CORD IS
DAMAGED, THE LUMINAIRE WILL NO LONGER BE USABLE,
AND THE LUMINAIRE MUST BE REPLACED.
IK10
1/3
www.filixlighting.com
WARRANTY
ALL PRODUCTS ARE FACTORY TESTED AND ARE GUARANTEED FREE
FROM FACTORY DEFECT FOR A PERIOD OF 36 MONTHS UNDER
FOLLOWING TERMS:
·PRODUCT HAS NOT BEEN SUBJECT TO INCORRECT VOLTAGE OR
POLARITY CONNECTION.
·PRODUCT HAS NOT BEEN SUBJECT TO PHYSICAL OR
ATMOSPHERIC DAMAGE.
·PRODUCT HAS BEEN RETURNED AND FACTORY EVALUATED FOR
DEFECT OR MALFUNCTION.
·ALL DRIVERS AND CONTROLLERS ARE APPROVED FOR USE BY
FILIX.
·THE LUMINAIRE FACTORY SEAL ( IP RATING ) HAS NOT BEEN
COMPROMISED
THE MANUFACTURER ACCEPTS NO RESPONSIBILITY FOR DAMAGE TO
PERSONS OR PROPERTY ARISING THROUGH IMPROPER USE OR
INSTALLATION.
ANY MODIFICATION OF THE LUMINAIRE WILL VOID ANY AND ALL
WRITTEN OR IMPLIED WARRANTIES.
STANDARD REPLACEMENT AND NORMAL
SERVICING TERMS.
ALL ELECTRONIC AND OTHER CONSUMABLE COMPONENTS ARE
SUBJECT OF EXCHANGE AFTER 36 MONTHS OF OPERATIONS.
PRODUCT PERFORMANCE DEPENDS OF CRITICAL ELECTRONIC AND
OTHER COMPONENTS WHICH CAN BE SERVICED WITH OFFICIAL
DEALER OR DIRECTLY WITH THE MANUFACTURER.
MANUFACTURER HOLDS THE RIGHT TO REPAIR AND CHANGE
COMPONENTS AS PER CURRENT COMPONENT AVAILABILITY.
MANUFACTURER CANNOT BE HELD LIABLE FOR COMPONENTS AND
OTHER EXPENSES ( DE-INSTALLATION, INSTALLATION, SHIPPING,
ETC.) INCURRED DURING THE PROCESS OF PRODUCT IMPROVEMENT
AND SERVICING.
THE LIGHT SOURCE CONTAINED IN THIS LUMINAIRE SHALL ONLY BE
REPLACED BY THE MANUFACTURER OR HIS SERVICE AGENT OR A
SIMILAR QUALIFIED PERSON.
NO PRESSURE
WASH
FIXTURE DIMENSIONS
WIRING
WIRE MARKINGS
+ BLACK WIRE
- WHITE WIRE
OPTION WITH SINGLE LED COLOR
+ BLACK WIRE
-R RED WIRE
-G GREEN WIRE
-B ORANGE WIRE
-W WHITE WIRE
OPTION WITH RGBW LED COLOR
www.filixlighting.com
2/3
NOTE:
IT ADVISED THAT CABLE LENGTH IS LONG ENOUGH THAT IT REACHES DRY AREA FOR SPLICE CONNECTION DRY AREA.
CONTROL GEAR USED TO POWER THIS LUMINAIRE SHALL BE SELV TYPE; HIGHEST ALLOWED UOUT TO BE MAX 10%
OF THE NOMINAL VOLTAGE OF CONTROL GEAR;MAXIMUM ALLOWED WIRING DISTANCE BETWEEN CONTROL GEAR AND
LUMINAIRE WITH STANDARD SUPPLIED CABLE IS 9 m OR 30˝. INSTALLATION OF LONGER WIRING LENGTHS SHOULD BE
DISCUSSED WITH MANUFACTURER PRIOR THE FIXTURE ORDERING. WHERE LUMINAIRE IS DELIVERED WITH CONNECTING
LEADS AND WITHOUT A MEANS OF CONNECTION TO THE POWER SUPPLY TERMINAL BLOCKS MAY BE USED (TERMINAL
BLOCKS SUPPLIED BY MANUFACTURER). IF TERMINAL BLOCKS IS LOST IT SHALL BE REPLACED FOR THE SAME IP
RATING AS THE LUMINAIRE ITSELF, WITH RATED VOLTAGE OF MIN. 400 V AND RATED CONNECTION CAPACITY OF 10A.
CONNECTION WIRE ENDS COMING FROM POWER SUPPLY TO BE PREPARED AS TERMINAL BLOCK MANUFACTURER
RECOMMENDS. TERMINAL BLOCK SHOULD BE PLACED IN A LOCATION WHERE IT DOESN'T NOT AFFECT THE LUMINAIRE
OPERATION.
INSTALLATION GUIDE
5
4
DETAIL A
CONCRETE
1
2
ANCHOR
2
4
4
GROUNDING
5
1. DRILL THE HOLE FOR ANCHOR
2. INSERT THE ANCHOR
3. CONNECT THE FIXTURE CABLE WITH SUPPLY CABLE
4. MOUNT THE FIXTURE AND GROUNDING WITH SCREW (GROUNDING
WIRE AND WIRES NOT SUPPLIED BY MANUFACTURER)
5. ROTATE FIXTURE TO THE DESIRED POSITION LIKE SHOWN ON
˝DETAIL A˝ AND FIX IT WITH ISO14583 M4x6 A4 SCREWS
(SCREWS SUPPLIED BY MANUFACTURER)
3/3
www.filixlighting.com
Andere Filix Unterwasserbeleuchtung Handbücher
Beliebte Unterwasserbeleuchtung Handbücher anderer Marken
Keldan
Keldan VIDEO 18X 25000lm CRI82 Bedienungsanleitung
Oase
Oase ProfiLux Garden LED RGB Bedienungsanleitung
Oceanled
Oceanled DISCOVER D3 Bedienungsanleitung
NORBIT
NORBIT AQUA FCL600 Bedienungsanleitung
Keldan
Keldan VIDEO 8XR Ambient 18000lm Bedienungsanleitung
Ikelite
Ikelite PCm - LED Light Bedienungsanleitung
