Fincor 2610MKII Series Technisches Dokument

BOOK 0959

SERIES 2610 MKII / 2601

SINGLE-PHASE

ADJUSTABLE-SPEED

DC MOTOR CONTROLLERS

(1/6 - 3 HP)

BOOK 0959

iii

TABLE OF CONTENTS

SECTION TITLE PAGE

I .......................................... GENERAL INFORMATION ...................................................................1

Introduction ...............................................................................................1

General Description...................................................................................1

Motor Selection .........................................................................................1

Model Types..............................................................................................2

II.......................................... INSTALLATION......................................................................................3

Installation Guidelines...............................................................................3

Installing the Controller ............................................................................5

Initial Startup...........................................................................................17

III ......................................... OPERATION ..........................................................................................19

Power On/Off ..........................................................................................19

Run ..........................................................................................................19

Stop .........................................................................................................19

Controlled Stop .......................................................................................19

Zero Speed Detection ..............................................................................19

Speed Control..........................................................................................20

Torque Control ........................................................................................20

Jog ...........................................................................................................20

Reverse....................................................................................................21

Load Monitor (Motor Timed Overload)..................................................21

Current Loop Transducers.......................................................................21

Armature Voltage and Current Outputs ..................................................21

Speed Regulator Input.............................................................................21

Inoperative Motor....................................................................................21

IV ......................................... MAINTENANCE AND REPAIR...........................................................23

General ....................................................................................................23

Adjustment Instructions ..........................................................................23

Troubleshooting Instructions...................................................................25

V.......................................... PARTS LIST ...........................................................................................29

VI ......................................... RATINGS AND SPECIFICATIONS .....................................................31

Ratings.....................................................................................................31

Operating Conditions ..............................................................................32

Performance Characteristics....................................................................32

Adjustments.............................................................................................33

Specifications ..........................................................................................33

VII ........................................ DRAWINGS ...........................................................................................35

INDEX ....................................................................................................39

BOOK 0959

LIST OF TABLES

TABLE TITLE PAGE

1................... Series 2610 MKII /2601 Model Matrix .................................................................................1

2................... Jumper J4 Position........................................................................................................................5

3 .................... Dip Switch (SW3) ........................................................................................................................6

4 .................... Initial Potentiometer Settings.....................................................................................................15

5 .................... Dynamic Braking Characteristics ..............................................................................................16

6 .................... Troubleshooting.................................................................................................................... 21-24

7 .................... Parts List, Series 2610 MKII / 2601 Controllers .......................................................................25

8 .................... Typical Application Data ...........................................................................................................27

9 .................... Operating Voltages and Signals.................................................................................................28

10................... Controller Weights .....................................................................................................................28

11................... Speed Regulation Characteristics...............................................................................................29

12................... Shunt Field Data .........................................................................................................................30

13................... Tachometer Feedback Voltage Selection ..................................................................................30

LIST OF ILLUSTRATIONS

FIGURE TITLE PAGE

1................... Controller Mounting Configurations .....................................................................................7

2................... Controller Mounting Dimensions ................................................................................................8

3 .................... Logic Connection Diagram, Run-Stop-Jog Switch.....................................................................9

4 .................... Logic Connection Diagram, Forward-Reverse Switch and Run-Stop-Jog Switch ....................9

5 .................... Logic Connection Diagram, Run-Stop Pushbuttons and Run-Jog Switch ...............................10

6 .................... Logic Connection Diagram, Run-Stop-Controlled Stop Pushbuttons and Run-Jog Switch....10

7 .................... Logic Connection Diagram, Optional Unidirectional Contactor Using Run-Jog Switch........11

8 .................... Logic Connection Diagram, Optional Unidirectional Contactor Using Run-Stop .................11

Pushbuttons and Run-Jog Switch

9 .................... Logic Connection Diagram, Optional Armature Contactor Reversing Using Switches..........12

10................... Logic Connection Diagram, Optional Armature Contactor Reversing Using Pushbuttons ....12

and Run-Jog Switch

11................... Logic Connection Diagram, Line Starting With Motor Speed Potentiometer .........................13

12................... Signal Connection Diagram, Motor Speed Potentiometer........................................................13

13................... Signal Connection Diagram, Tachometer Feedback.................................................................14

14................... Signal Connection Diagram, Current (Torque) Reference Potentiometer................................14

15................... Signal Connection Diagram, Line Starting Without a Motor Speed Potentiometer ................14

16................... Signal Connection Diagram, 4-20mA Interface........................................................................15

17................... Signal Connection Diagram, 4-20mA Transducer with Auto/Manual Switch ........................15

18.................. Signal Connection Diagram, Transducer with External Burden Resistor................................15

19................... Signal Connection Diagram, PID Controller with Auto/Manual Switch .................................16

20................... Signal Connection Diagram, 4-20mA Outputs – Armature Amps and Volts..........................16

21................... Signal Connection Diagram, 0-10Vdc Outputs – Armature Amps and Volts .........................16

22................... Functional Schematic, Series 2610 MKII / 2601 ......................................................................36

23................... Series 2610 MKII / 2601 Control Board, 1/6 – 3HP.................................................................37

BOOK 0959

WARNING

The following must be strictly adhered to at all times.

1. YOU AS THE OWNER OR OPERATOR OF FINCOR EQUIPMENT HAVE THE RESPONSIBILITY

TO HAVE THE USERS OF THIS EQUIPMENT TRAINED IN ITS OPERATIONS AND WARNED OF ANY

POTENTIAL HAZARDS OF SERIOUS INJURY.

2. THE DRIVE EQUIPMENT SHOULD BE INSTALLED, OPERATED, ADJUSTED, AND SERVICED

ONLY BY QUALIFIED PERSONNEL FAMILIAR WITH THE CONSTRUCTION AND OPERATION

OF THE EQUIPMENT AND THE HAZARDS INVOLVED INCLUDING THOSE DESCRIBED

BELOW. FAILURE TO OBSERVE THIS WARNING CAN RESULT IN PERSONAL INJURY, LOSS OF LIFE,

AND PROPERTY DAMAGE.

3. THE NATIONAL ELECTRICAL CODE REQUIRES THAT AN AC LINE FUSED DISCONNECT OR

CIRCUIT BREAKER BE PROVIDED IN THE AC INPUT POWER LINES TO THE CONTROLLER. THIS

DISCONNECT MUST BE LOCATED WITHIN SIGHT OF THE CONTROLLER. DO NOT OPERATE

THE CONTROLLER UNTIL THIS CODE REQUIREMENT HAS BEEN MET.

4. THE DRIVE EQUIPMENT IS AT AC LINE VOLTAGE WHENEVER AC POWER IS CONNECTED TO

THE DRIVE EQUIPMENT. CONTACT WITH AN ELECTRICAL CONDUCTOR INSIDE THE DRIVE

EQUIPMENT OR AC LINE DISCONNECT CAN CAUSE ELECTRIC SHOCK RESULTING IN

PERSONAL INJURY OR LOSS OF LIFE.

5. BE SURE ALL AC POWER IS DISCONNECTED FROM THE DRIVE EQUIPMENT BEFORE

TOUCHING ANY COMPONENT, WIRING, TERMINAL, OR ELECTRICAL CONNECTION IN THE

DRIVE EQUIPMENT.

6. ALWAYS WEAR SAFETY GLASSES WHEN WORKING ON THE DRIVE EQUIPMENT.

7. DO NOT REMOVE OR INSERT CIRCUIT BOARDS, WIRES, OR CABLES WHILE AC POWER IS

APPLIED TO THE DRIVE EQUIPMENT. FAILURE TO OBSERVE THIS WARNING CAN CAUSE

DRIVE DAMAGE AND / OR PERSONAL INJURY.

8. ALL DRIVE EQUIPMENT ENCLOSURES, MOTOR FRAMES, AND REMOTE OPERATOR

STATIONS MUST BE CONNECTED TO AN UNBROKEN COMMON GROUND CONDUCTOR. AN

UNBROKEN GROUNDING CONDUCTOR MUST BE RUN FROM THE COMMON GROUND

CONDUCTOR TO A GROUNDING ELECTRODE BURIED IN THE EARTH OR ATTACHED TO A

PLANT GROUND. REFER TO THE NATIONAL ELECTRICAL CODE AND LOCAL CODES FOR

GROUNDING REQUIREMENTS.

9. THE ATMOSPHERE SURROUNDING THE DRIVE EQUIPMENT MUST BE FREE OF COMBUSTIVE

VAPORS, CHEMICAL FUMES, OIL VAPOR, AND ELECTRICALLY CONDUCTIVE OR CORROSIVE

MATERIALS.

10. SOLID-STATE DEVICES IN THE CONTROLLER CAN BE DESTROYED OR DAMAGED BY

STATIC ELECTRICITY. THEREFORE, PERSONNEL WORKING NEAR THESE STATICSENSITIVE

DEVICES MUST BE APPROPRIATELY GROUNDED.

BOOK 0959

SECTION I

GENERAL INFORMATION

INTRODUCTION

This manual contains installation, operation, and maintenance and repair instructions for Fincor Series 2610 MKII /

2601 Single-Phase Adjustable-Speed DC Motor Controllers. A parts list, ratings and specifications, and drawings are

also included.

GENERAL DESCRIPTION

Series 2610 MKII / 2601 Controllers statically convert AC line power to regulated DC for adjustable-speed armature

control of shunt-wound and permanent-magnet motors.

Series 2610 MKII / 2601 Controllers comply with applicable standards established by the National Electrical Code and

NEMA for motor and industrial control equipment. The controllers are Underwriters Laboratories Listed (File No.

E184521) UL/cUL.

MOTOR SELECTION

Series 2610MKII / 2601 Controllers control the operation of general purpose DC motors designed for use with solid-

state rectified power supplies. The motor may be shunt-wound, stabilized shunt-wound, or permanent magnet. For

maximum efficiency, the motor should be rated for operation from a NEMA Code K power supply.

BOOK 0959

MODEL TYPES

TABLE 1. SERIES 2610 MKII / 2601 MODEL MATRIX

FUNCTION CONFIGURATION OPERATOR CONTROLS

POWER

SOURCEa&

HP RANGE

MODEL RUN

STOPb

RUN-

STOP-

DBc

ARMATURE

SWITCH

REVERSEb

ARMATURE

CONTACT

AND DBc

ARMATURE

CONTACT

REVERSE

AND DBc

OPEN

CHASSIS ENCLOSED LOCAL

INTEGRAL REMOTE 115V 230V

2601 X X X

2601A X X X X

2601P0 X X X

2601P1 X X X

2601AP0 X X X X

2601AP3 X XdX X

2601B X X X X

2601BP0 X X X X

2601BP1 X X X X

1/6-1 1/3-3

2611 X X X

2611A X X X X

2611P0 X X X

2611P1 X X X

2611P2 X X X X

2611B X X X X

2611AP0 X X X X

2611AP3 X

XdX X

2611BP0 X X X

2611BP1 X X X X

1/6-1 1/3-2

2612 X X X

2612A X X X X

2612B X X X X

1/6-1 1/3-3

2615 X X X

2615A X X X X

2615B X X X X

1/6-1 1/3-2

a. Units are reconnectable

b. No armature contactor

c. Includes armature contactor

d. Includes Forward/Reverse switch

BOOK 0959

SECTION II

INSTALLATION

Before starting the installation, read this section thoroughly. In addition, a thorough review of the Ratings and

Specifications (Section VI) is recommended. The following installation guidelines should be kept in mind when

installing the controller.

INSTALLATION GUIDELINES

1. CONTROLLER MOUNTING - The controller may be mounted either vertically or horizontally. However, never

mount the controller upside down, immediately beside or above heat generating equipment, or directly below water or

steam pipes.

The controller must be mounted in a location free of vibration.

Multiple controllers may be mounted side by side, as close to each other as the mounting feet will allow.

The minimum clearance at the top and bottom of the controller may be as narrow as the conduit fittings allow.

2. ATMOSPHERE - The atmosphere surrounding the controller must be free of combustible vapors, chemical fumes,

oil vapor, and electrically conductive or corrosive materials.

The air surrounding an enclosed controller must not exceed 40 degrees C (104 degrees F), and the air surrounding an

open-chassis controller must not exceed 55 degrees C (131 degrees F). Minimum air temperature is 0 degree C (32

degrees F) for enclosed and open-chassis controllers.

3. CONTROLLER CONSTRUCTION - The controller base is made of die-cast aluminum with a powdered epoxy

finish, and the cover is made of a die-cast aluminum alloy.

The controller enclosure is totally enclosed, non-ventilated, and complies with NEMA Type 4 and 12 standards. There

is an oil resistant synthetic rubber gasket between the cover and base. Those models with integral operator controls

include flexible boots to seal the switches, and a seal for the MOTOR SPEED potentiometer.

4. LINE SUPPLY - The controller should not be connected to a line supply capable of supplying more than 100,000

amperes short-circuit current. Short-circuit current can be limited by using an input supply transformer of 50 KVA or

less, or by using correctly sized current limiting fuses in the supply line ahead of the controller. Do not use a

transformer with less than the minimum transformer KVA listed in Table 8, page 31.

If rated line voltage is not available, a line transformer will be required. If the line supply comes directly from a

transformer, place a circuit breaker or disconnect switch between the transformer secondary and the controller. If power

is switched in the transformer primary, transients may be generated which can damage the controller. See Table 8 (page

31) for minimum transformer KVA.

Do not use power factor correction capacitors on the supply line to the controller.

A 20 Joule metal oxide varistor (MOV) is connected across the controller terminals. If higher energy transients are

present on the line supply, additional transient suppression will be required to limit transients to 150% of peak line

voltage.

BOOK 0959

When a 115 VAC line supply is used, connect the white (common) wire to Terminal L2 and connect the remaining

(hot) wire to Terminal L1.

5. ISOLATION TRANSFORMER - While not required, an isolation transformer can provide the following

advantages:

a. Reduce the risk of personal injury if high voltage drive circuits are accidentally touched.

b. Provide a barrier to externally generated AC supply transients. This can prevent controller damage from abnormal

line occurrences.

c. Reduce the potential for damaging current if the motor armature, motor field, or motor wiring becomes grounded.

6. GROUNDING - Connect the green or bare (ground) wire of the line supply to the ground screw located near the top

conduit entry hole in the controller base. Then ground the controller base by connecting the ground screw to earth

ground.

The motor frame and operator control stations must also be grounded.

Personal injury may occur if the controller, motor, and operator stations are not properly grounded.

7. WIRING PRACTICES - The power wiring must be sized to comply with the National Electrical Code, CSA, or

local codes. Refer to the controller data label for line and motor current ratings.

Do not use solid wire.

Signal wiring refers to wiring for potentiometers, tachometer generators, and transducers. Control wiring refers to

wiring for operator controls, e.g., switches and pushbuttons. Signal and control wiring may be run in a common

conduit, but not in the same conduit as the power wiring. In an enclosure, signal and control wiring must be kept

separated from power wiring and only cross at a 90 degree angle to reduce electrical noise.

If shielded wire (such as Alpha 2422 - two conductor, 2423 - three conductor, 2424 - four conductor) is used for the

signal and control wiring, connect the shields to chassis ground (ground screw on the controller base) and tape the

opposite ends of the shields. Twisted cable is also suitable for signal and control wiring.

Two 3/4-14 NPT threaded holes are provided for conduit entry, one each in the top and bottom of the controller.

BOOK 0959

INSTALLING THE CONTROLLER

1. Remove the controller front cover (if used) by removing the four cover screws.

2. Check components in the controller for shipping damage. Report shipping damage to the carrier.

3. Check the controller and motor data labels to be sure the units are electrically compatible.

4. Be sure the controller has been calibrated correctly for the motor being used. Calibration is performed by

changing the position of a Jumper J4 on the controller control board to comply with Table 2. To change the position

of Jumper J4, pull the jumper from the control board and then push it onto the appropriate two pins on the board. For

the location of J4, see Figure 23 (page 37).

TABLE 2. JUMPER J4 POSITION

MOTOR ARMATURE CURRENT RATING (AMPERES)

JUMPER

POSITIONa2 HP Maximum 3 HP Maximum

100% 10 15

80% 8 12

60% 6 9

40% 4 6

20% 2 3

a. Select the position closest to the motor nameplate armature current rating.

5. Check the positions of Jumpers J1, J2, and J3 on the control board. For the locations of J1, J2, and J3, see Figure 23,

page 37. For a 230 VAC line supply and a 180V armature motor, Jumper J1 must be in the 230V position, and Jumpers

J2 and J3 must be in the 180V position. For a 115 VAC line supply and a 90V armature motor, J1 must be in the

115V position, and J2 and J3 must be in the 90V position. To change the position of J1, J2, or J3 pull the jumper

from the control board and then push it onto the appropriate pins on the board.

NOTE: If Option 1001 (Armature Contactor, Unidirectional), 1004 (Armature Contactor, Reversing), or 1775 (Signal

Interface) is to be installed in the controller, do not offset the five-position plug (supplied with the option) at Connector

J1 on the control board. Do not confuse Connector J1 with Jumper J1. Refer to the Instruction Sheet (ISP0703,

ISP0666, ISP0653, respectively) supplied with the option for connection instructions.

6. The controller may be surface mounted or panel mounted as shown in Figure 1, page 7. Mount the controller.

Mounting dimensions are shown in Figure 2, page 8.

7. Conduit entry is made by punching out the knockout at the top or bottom of the controller base. To prevent

component damage from knockout fragments, apply masking tape to the inside of the knockout before punching.

8. Connect the power wiring to Terminals L1, L2, A1 (+), A2 (-), F+ and F-. Be sure to observe Installation Guidelines

4 and 7 on pages 3 and 4. If half-wave shunt field voltage is desired, connect one of the motor shunt field leads to

Terminal F/2 (see Table 12 on page 34).

NOTE: Low inductance motors require a full-wave field to prevent current instability.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fincor Controller Handbücher

Fincor

Fincor 2600 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung