Finecom Co., Ltd. FLM-520 Bedienungsanleitung

finecom
FLM-520 User’s Guide
--
1
TFT LCD monitor TFT LCD monitor TFT LCD monitor TFT LCD monitor TFT LCD monitorTFT LCD monitor TFT
FLM-520
User’s Guide
FLM-520 LCD Monitor
Finecom Co., Ltd.
Fine B/D. 673-5 Dungchon-dong,
Kangseo-ku, Seoul 157-030, Korea.
Tel : 82-2-3662-5811
Fax : 82-2-3663-0987
Web site : http://www.finecom.co.kr
fine&good fine&good fine&good fine&good fine&good fine&good fine&good fine&good fine&good fine&good fine&good

finecom
FLM-520 User’s Guide
--
2
Index
FCC Notice 4
1. Outline 5
1-1) Introduction to FLM-520 5
1-2) Features 5
2. Components & parts name 6
2-1) Components 6
2-2) Front & Rear View 6
3. Installation 7
4. Speaker 8
5. External Keypad 9
5-1) External Keypad 9
5-2) Function of Push-button 9
6. OSD Overview 10
6-1) Power On Default Settings 10
6-2) Value Controls 10
6-3) LED Active Source Indicator 10
6-4) Warning Message 10
7. OSD Menu Items 11
7-1) RGB Menu 12
7-1-1) Brightness 12
7-1-2) Red and Blue Controls 12
7-1-3) Green... 12
7-1-4) Blue ... 12
7-1-5) Color Temp 12
7-1-6) Sharpness 12

finecom
FLM-520 User’s Guide
--
3
7-2) Geometry Menu 13
7-2-1) Auto-Adjustment 13
7-2-2) H. Position 13
7-2-3) V. Position 13
7-2-4) H. Total 13
7-2-5) Auto Phase 13
7-2-6) Delay 13
7-3) Contrast Menu 14
7-3-1) Auto-Balance 14
7-3-2) Contrast 14
7-3-3) Red 14
7-3-4) Green 14
7-3-5) Blue 14
7-4) Info 15
7-5) Input Type 15
7-6) Speaker Volume 16
7-7) Auto Config 16
7-8) NVRAM Init 16
7-9) Power Down 16
7-10) Revert 16
7-11) Save 16
8. Windows Driver installation 17
9. Specification 18
10. Problems and Check Points 19
Table1: Analog RGB Input Port Signal Description 19
Table2: Supported RGB PC Graphics Input Formats20

finecom
FLM-520 User’s Guide
--
4
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interferences to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit difference from that to which the receiver
is connected.
•Consult the dealer of an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables
must be used with the unit to insure compliance.

finecom
FLM-520 User’s Guide
--
5
1. Outline
1-1) Introduction to FLM-520
FLM-520 is a display device which transforms analogue signals of Graphic inputs
(Video signals of VGA, SVGA and XGA) into digital signals and displays them on
LCD panel. The user can select OSD Menu items by using external keypad to adjust
Brightness, Contrast, Color, Position and etc.for best working condition.
Digital/NTSC/PAL is optionally supported
1-2) Features
FLM-520 (15 inch) is the best choice at any applications of financial, industry,
government in which working pace, weight and reliance should be thought. This 15
inch LCD monitor provides a viewing area equivalent to a 17 inch CRT monitor.
Imbedded 1.5W 2 speakers, displays bright and sharp screen of 200 cd/m2. To provide
optimized working environment it can be tilted forward 5 degrees and backward 10
degrees, and swiveled left/right 45 degrees each.

finecom
FLM-520 User’s Guide
--
6
2.Components & Parts names
2-1) Components
Figure 2-1) : Components
2-2)Front & Rear View
Figure 2-2) Front View Figure 2-3) Rear View

finecom
FLM-520 User’s Guide
--
7
3. Installation
1) Connect the input plug to FLM-520 LCD monitor.
(Connect 15 pin RGB connector, for analogue RGB input, to FLM-312 as shown Figure
2-3).
2) Connect the 12V Adapter to FLM-520.
(When you turn on power switch, LED on the board will light Red, Green in turn and
then green will remain.)
3) Adjust parameters of OSD Menu by using External keypad.
(Automatic Configuration is convenient to use; When power on or screen mode changes,
optimized conditions are made automatically)
4) If there is something wrong with Video Cable or PC power is off, the message of “No
Sync”is displayed on the screen. When this condition continues 10 seconds, LED on the
board lights red and then the power of LCD panel is automatically cut off. Once Video
cable is connected or PC power turns on, LED lights Green and LCD panel power is
restored.

finecom
FLM-520 User’s Guide
--
8
4. Speaker
A speaker plug is ready at the rear of this LCD monitor. It is installed as follows;
1) Connect the PC Audio jack to FLM-520 Speaker plug.(1.5W 8Ohm, Stereo)
2) Select Speaker volume at OSD initial Menu and then adjust the volume.
( After adjusting the volume, it shall be saved at the Initial Menu in order to keep
the setup volume when power on and off.
3) Decrease the volume when it is not used.
( 1.5 W Dual Amplifier is imbedded and it can bring noise when volume is too high)

finecom
FLM-520 User’s Guide
--
9
5. External Keypad
5-1) External Keypad
AT the rear left side External Keypad is ready for user’s interface, it is configured as
below :
Figure 5-1) External Keypad Block Diagram
If MENU button is pressed, the OSD MENU is displayed. The user can select the Menu
item by pushing SEL button, and then adjust the selected values and or move to below
Menu by using +(Right) and –(Left) buttons. Adjusted value shall be saved at OSD
Menu in order to keep it during power on and off.
5-2) Function of Push button
There are 4 buttons to do following functions.
MENU :To start or terminate Menu or move to upper Menu.
SEL (Down):To move to the item’s position to be selected.
LEFT (-):To decrease the selected parameter value or to move to below Menu.
RIGHT (+):To increase the selected parameter value or to move to below Menu.
-(Left)
+(Right)
Sel(Down)
Menu
LED
Power Switch

finecom
FLM-520 User’s Guide
--
10
6. OSD Overview
6-1) Power On Default Settings
FLM-520 devices are initialized during power-on to the last saved conditions.
During OSD all parameters are saved only when the user select SAVE at the Menu.,
In case the user exits the menus without selecting SAVE at Menu, the parameters are
applied only at present conditions and when Power on/off, it is returned to the last saved
value.
6-2) Value Controls
Many parameters value of Tree-type Menu can be adjusted by using the
+(Right) and –(Left) buttons. SEL button is pressed to move to the next item.
In order to move to the upper Menu, Menu button may be used or “Main Menu”
item is selected.
6-3) LED Active Source Indicator
When the LED lights Green, the monitor is ready to use normally.
When the LED lights Red, Power may be cut off because there is something wrong with
Video Input and or LCD panel power may be off when the user selected ‘Power Down’
at OSD Menu.
6-4) Warning Message
A warning message as in Figure 6-1 is displayed when the system detects that an RGB
Video cable is not connected to the FLM-520 monitor. The message is displayed for a
maximum of 10 seconds until the cable is connected.
A message in Figure 6-2 is displayed in case of not-supported Video Mode. Please refer
to Table 2 for supportable Video Modes.
Figure 6-1) No RGB Warning Message Figure 6-2 ) Unsupported Input Warning
Message
No Sync Video Change Mode
Inhaltsverzeichnis

















