FingerTec TA200 Plus Bedienungsanleitung

Back Plate

4 feet / 1.2 meter

(recommended)

TA200 Plus

TCP/IP PORT (LAN)

USB PORT

POWER

ADAPTER PORT

Step 1

Determine the Location and Positioning

of the Installation

• Avoid installing the terminals in locations that has contact with

a strong light source (e.g direct sunlight, spotlight, fluorescent

light, etc)

• Avoid installing the terminals in locations with high moisture or

condensation levels in the air

• The recommended installation height of the terminal from the

ground is 1.2 meter.

Step 2

Mounting of Terminals

A. MOUNT ON WALL

• After determining the height of the terminal from the ground

level and have made the relevant marks on the wall, drill the

screws into the wall to hang the back plate.

Refer to Appendix II for dimensions and measurements of instal-

lation.

Installation Guide

TA200 Plus

Fingerprint Color Multimedia for

Time Attendance System

B. FLEXI KIT

FingerTec offers flexi-kit for all its time attendance models. Attach

the terminal on the flexi-kit for convenience.

Step 3

Wiring for Power Supply

The power jack is positioned at the rear of the terminal, labeled

Power Adapter Port in the below diagram.

Step 4

Setting Up Data Communications

(Skip this step if you are using USB ash disk to transfer data)

TCP/IP – LAN Connection

For TCP/IP connection, plug the special RJ45 jack into the TCP/IP

(LAN) Port of the terminal. Connect the other end (normal RJ45

jack) to the local area network hub or a PC. Configure the device ID,

IP address, subnet mask and Gateway in the terminal (refer to the

hardware user manual for details).

Note:

All Accessories are offered at

http://accessory.fingertec.com

Step 5

Finalizing the installation

1. Check that all cable connections are done correctly.

2. Attach the terminal to the corresponding back plates, tighten

the screws to secure the terminal on the wall

3. Switch on the power to the terminal.

4. Start using the terminal.

Other Accessories

AdapTec AC

The AdapTec AC is a 12VDC power supply inclusive of a 110~240VAC

switching linear power. The AdapTec supplies 12VDC power to the

FingerTec terminal and door lock system as well as charges a 12VDC

7.0Ah backup battery simultaneously. During an event of a power

failure, the back up battery automatically provides power to the

terminal and maintains the door lock system. The AdapTec AC also

prevents a secured door from being opened if it has been tampered

with.

Mini UPS

Mini UPS 12VDC is a mini portable backup power

supply with 12VDC output, supplying 12VDC

power for FingerTec Door Access & Time Attend-

ance terminals.

Enclosures

FingerTec offers enclosures to protect the terminals from being med-

dled with by unauthorized persons.

Flexi Kit

A foldable stand for FingerTec products, simplifies installation and

presentable. (Example on Step 2, B.)

Appendix I

Terminal Dimensions and Measurements

Front View of TA200 Plus

Andere FingerTec Sicherheitssystem Handbücher

FingerTec

FingerTec h2b Bedienungsanleitung

FingerTec

FingerTec FaceID 3 Bedienungsanleitung

FingerTec

FingerTec TA700W Bedienungsanleitung

FingerTec

FingerTec m-Kadex Bedienungsanleitung

FingerTec

FingerTec AdapTec Plus Montageanleitung

FingerTec

FingerTec TA100C Bedienungsanleitung

FingerTec

FingerTec TA100 DIY SERIES Bedienungsanleitung

FingerTec

FingerTec TA500 Bedienungsanleitung

FingerTec

FingerTec AC100C Bedienungsanleitung

FingerTec

FingerTec m-Kadex Bedienungs- und Wartungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung