FIORENTINI TX-05 Bedienungsanleitung
Operator’s manual
TX-05
ATTENTION! DON’T USE THE MACHINE WITHOUT READING THE
OPERATOR’S MANUAL
1
INTRODUCTION
RECEIPT OF THE MACHINE Pag. 2
INTRODUCTION 2
TECHNICAL DESCRIPTION 3
GENERAL INFORMATION 4
MANUFACTURER RESPONSABILITIES 4
CLAIMS 4
TRANSPORTATION 5
HANDLING OF PACKED MACHINE 5
UNPACKING THE MACHINE 5
HANDLING OF UNPACKED MACHINE 5
RULES TO BE RESPECTED FOR THE CORRECT USE 5
INSTRUCTION FOR USE 6
OPERATOR QUALIFICATION 6
VEHICLE INSPECTION 6
BATTERY ASSEMBLING 6
CONTROLS DESCRIPTION 7
USE 8-9
BATTERIES 10
BATTERIES TECHNICAL DESCRIPTION 10
MAINTENANCE 11
CLEANING 11
2
RECEIPT OF THE MACHINE
AS SOON AS THE MACHINE IS UNPACKED PLEASE CHECK THE MACHINE
AND BE SURE THAT EVERYTHING IS OK AND THAT NO DAMAGES
HAPPEN DURING TRANSPORTATION.
BE SURE THAT ALL THE PARTS HAVE BEEN SHIPPED .
FOR ANY PROBLEMS CONTACT IMMEDIATELY THE MANUFACTURER.
INTRODUCTION
THIS MACHINE CAN TOW TROLLEYS FOR A MAXIMUM OF 500 Kg
WITHOUT ANY PROBLEM.
THIS MACHINE CAN BE EQUIPPED WITH FRONT MOP KIT .
THIS KIT IS ABLE TO CLEAN ANY KIND OF FLOOR.
THE BEST PERFORMANCES CAN BE GARANTEE ONLY USING PROPERLY
THE MACHINE .
PLEASE READ CAREFULLY THE INSTRUCTION
THE MACHINE CAN BE USED ONLY FOR THIS PURPOSE
Keep always this manual for future reference
3
TECHNICAL DESCRIPTION
Length 1250 mm
Width 680 mm
Height 980 mm
Wheels 3
Wheel diameter 310 mm
Traction Electric
Weight without batteries 60 Kg
Battery compartment
(LxWxH ) 350 x 300 x 250 mm
Batteries specifications No.2 x12 volt –95 Amp.
Power 24 volt –350 W
or
24 volt –600 W
Service Foot pedal
Parking brake lever
Max forward speed 9 Km / h
U turn 2000 mm
4
GENERAL INFORMATION
MANUFACTURER RESPONSABILITIES
The manufacturer Ing.O.Fiorentini is not responsible for any failures, accidents, etc due to the not
correct use of the machine .
The same applies to any change , modifications or installation of any accessory not authorized.
Ing.O.Fiorentini is not responsible for any damage caused by:
??Natural calamity
??Wrong operation
??No maintenance
The manufacturer is not responsible for any changes not authorized
CLAIMS
Ing.O.Fiorentini needs to receive the follow information
??Model of the machine
??Serial number
??Year
??Defected fault description
??Checks that have been done
??Any other information considered useful for this purpose
Fig. 1
Ing. O. Fiorentini S.r.l.
50030 Piancaldoli (Fi)
MADE
IN
ITALY
CE
Mod. S.N. 2003
V Hz.
Kg A W
5
TRANSPORTATION
HANDLING OF PACKED MACHINE
The machine is supplied packed on pallet, closet and made by plywood or paper board.
UNPACKING THE MACHINE
1. Cut the straps .
2. Remove the clips on the paper board base
3. In case of package made by plywood remove the clips on the sides and on the base of each
panel
4. Remove the other clips fastening the machine
5. Bring the machine at ground level
HANDLING OF UNPACKED MACHINE
1. Check the unpacked machine and mount the batteries(pag7)
RULES TO BE RESPECTED FOR CORRECT USE
The machine is studied for only one person, so is forbidden to carry another one.
It is important to use the machine carefully and to take care of people around .
When the vehicle is not used is necessary to use the parking brake.
Never carry more than the authorized weight
6
INSTRUCTION FOR USE
OPERATOR QUALIFICATION
The machine can be used only by an authorized operator .
The operator must be instructed in a proper way .
VEHICLE INSPECTION
It is important that the machine is keep in a good condition and that all maintenance is done
properly.
??Check the vehicle status and the wheel pressure
??Check the batteries autonomy
??Check the stop performances in both direction
??Check turning performance
If the machine has any problem , please stop immediately the machine and call the person in charge
of maintenance
BATTERY ASSEMBLING
??Remove the battery compartment cover
??Put the batteries in the compartment(fig 3)
??Connect the batteries using the cables(fig3A)
??Put the battery compartment cover
Fig. 3 Fig. 3-A
7
CONTROLS DESCRIPTION
1 2 3 4 5 6
Fig. 4
7 9 8
1 Parking brake lever Pulling the lever the parking brake is in function
2 Disconnected parking
brake lever Pushing together with service brake lever
3 High speed lamp Is switched on when the high speed is choose
4 Battery indicator It shows the batteries autonomy
5 Forward and backward
switch When the switch is in forward position the machine goes in
front , when in backward position the machine goes back
6 Acceleration control For acceleration turn the hand grip.
7 Main switch To switch on the machine put the switch on position.
To switch off put the switch off position
8 High speed switch When the switch is on position the high speed is connected
9 Steering adjustment The operator can chose the wished position
8
USE
Before using the vehicle understand very well all the functions and read the instruction manual
Main Switch:
The vehicle is equipped with a main switch placed on the steering To use the vehicle put the switch
ON position. To stop the vehicle put the switch OFF position
Steering:
The steering and the handle bar are similar to the scooter ones.
To turn left go in anti clock position. To turn right go clock position
The vehicle has a very short radius and it is very important in order to have excellent
maneuvrerability with less speed
When is necessary to turn please moderate the speed!!
Acceleration hand grip:
The acceleration hand grip is placed on the right position of the steering and is similar to the scooter
ones.
Turning the hand grip the vehicle is moved .
Foot pedal brake:
The service brake is placed on the left side of the operator.
N.B. In order to use in a proper way the parking brake ( placed on the left side of the steering)
please push completely the foot pedal brake (Fig. 4).
9
Steering adjustment:
It is very simple to adjust the steering position by the lever placed on the steering itself (fig. 5).
Adjustment lever steering inclination
Fig. 5
Seat adjustment lever:
Placed on the right position , allows the operator to chose the wished position
Fig. 6
Seat adjustment lever
Inhaltsverzeichnis
