Fiplex NanoSAW Series Bedienungsanleitung

ano

SAW

Series

peater

User’s Manual

November 2009

UM-0101-01.09 – November 2009

Document History

Description

Revision

Date Issued

Preliminary release for early field trials 0.0 September 10

, 2009

Preliminary release, screenshots updated 1.0 November 1

, 2009

UM-0101-01.09 – November 2009

III

About this manual

This manual describes installation, commissioning, usage, function, operation and maintenance of Fiplex

nanoSAW series repeater and Fiplex portable Operational and Maintenance Software (pFOMS). The first

part of the manual describes the repeater hardware and the second part describes the software.

Hardware and software mentioned in this manual are subjected to continuous development and improvement.

Consequently, there may be minor discrepancies between the information in the manual and the performance

and design of the hardware and software. Specifications, dimensions and other statements mentioned in this

manual are subject to change without notice.

This manual or parts of it may not be reproduced without the written permission of Fiplex Europe SL.

UM-0101-01.09 – November 2009

ontents

Abbreviations ..................................................................................................................................V

Part 1 HARDWARE......................................................................................................................... 1

1. Safety.......................................................................................................................................1

FCC Radiation Hazard Warning....................................................................................................1

R&TTE Compliance Statement.....................................................................................................1

Disposal of Electric and Electronic Waste.....................................................................................1

2. Installation ................................................................................................................................2

Sitting the repeater .......................................................................................................................2

Mounting.......................................................................................................................................2

3. Commissioning.........................................................................................................................3

Connection...................................................................................................................................3

Starting operation.........................................................................................................................4

Status Indicators...........................................................................................................................5

Automatic Gain Control (AGC)......................................................................................................7

Overload Protection......................................................................................................................7

Downlink Signal Indicator .............................................................................................................7

Laboratory Measurements............................................................................................................7

Part 2 SOFTWARE ......................................................................................................................... 8

4. Installation ................................................................................................................................8

5. Overview.................................................................................................................................14

General Tabsheet.......................................................................................................................14

Status tabsheet...........................................................................................................................15

Configuration..............................................................................................................................16

UM-0101-01.09 – November 2009

Abbreviations

AGC Automatic Gain Control

AMPS Advanced Mobile Phone Service

ARFCN Absolute Radio Frequency Channel Number

BCCH Broadcast Control Channel (GSM broadcast channel time slot)

BS Base Station, BS antenna = towards the base station

CDMA Code Division Multiple Access

DC Direct Current

DCS Digital Communication System (same as PCN)

DL Downlink signal direction (from base station via repeater to mobile station)

DPLX Duplex filter

EEPROM Electrical Erasable Programmable Read Only Memory

EGSM Extended Global System for Mobile communication

ETACS Extended Total Access Communication System

ETSI European Telecommunications Standard Institute

GSM Global System for Mobile communication

HW Hardware

LED Light Emitting Diode

LNA Low Noise Amplifier, uplink and downlink

MS Mobile Station, MS antenna = towards the mobile station

OMS Operation and Maintenance System

OL Overload

PA Power Amplifier

PCN Personal Communication Network (same as DCS)

PCS Personal Communication System

pFOMS Portable Fiplex Operation and Maintenance Software

PS Power Supply

RF Radio Frequency

RSSI Received Signal Strength Indication

SW Software

TDMA Time Division Multiple Access

UL Uplink signal direction (from mobile station via repeater to base station)

WEEE Waste of Electric and Electronic Equipment

UM-0101-01.09 – November 2009 1

Part 1 HARDWARE

1. Safety

Any personnel involved in installation, operation or service of Fiplex repeaters must understand

and obey the following:

Any repeater, including this repeater, will generate radio signals and thereby give rise to

electromagnetic fields that may be hazardous to the health of any person who is extensively

exposed to the signals at the immediate proximity of the repeater and the repeater antennas.

FCC Radiation Hazard Warning

To comply with FCC RF exposure requirements in Section 1.1307 and 2.1091 of FCC Rules, the

antenna used for this transmitter must be fixed-mounted on outdoor permanent structures with a

separation distance of at least 2 meter from all persons.

R&TTE Compliance Statement

This equipment complies with the appropriate essential requirements of Article 3 of the R&TTE

Directive 1999/5/EC.

BTS chassis, Repeater, feeders, donor antenna, service antenna/s and auxiliary equipment (splitters, tabs,

.etc) are required to be bonded to protective grounding using the bonding stud or screw provided

with each unit.

Static electricity means no risk of personal injury but it can severely damage essential parts of

the repeater, if not handled carefully.

Parts on the printed circuit boards as well as other parts in the repeater are sensitive to

electrostatic discharge.

Never touch printed circuit boards or uninsulated conductor surfaces unless absolutely

necessary.

If you must handle printed circuit boards or uninsulated conductor surfaces, use ESD protective

equipment, or first touch the repeater chassis with your hand and then do not move your feet on

the floor.

Never let your clothes touch printed circuit boards or uninsulated conductor surfaces.

Disposal of Electric and Electronic Waste

Pursuant to the WEEE EU Directive electronic and electrical waste must not be disposed of with unsorted

waste. Please contact your local recycling authority for disposal of this product.

UM-0101-01.09 – November 2009

2. Installation

Sitting the repeater

Fiplex nanoSAW family of repeaters is designed for indoor use.

If repeater needs to be mounted outdoors, weather proof cabinet should be provided in order to

preserve weather tightness.

Mounting

nanoSAW is ready for wall mount using four fixing screws.

Figure 1

Figure 1 shows holes pattern for fixing screws.

UM-0101-01.09 – November 2009

3. ommissioning

Connection

1. Connect service antenna (“TO MOBILE” port) and donor antenna (“TO BASE” port) coaxial

cables. SMA type female connectors are used in the repeater.

2. Once RF ports of the repeater are properly loaded connect the DC plug from power supply to

nanoSAW DC input.

The repeater powers on when power supply is connected to the AC line, and nanoSAW is

properly feed with DC voltage. Blue led labelled “PWR ON” must be on, under normal power

conditions.

Figure 2

Figure 2 shows DC input plug position.

UM-0101-01.09 – November 2009

Starting operation

Prior to the following steps refer to section 2 of this manual in order to properly install pFOMS.

1. Setup desired filter configuration using pFOMS (only for programmable band selective and

programmable channel selective models).

In programmable band selective repeaters user must set up start and stop frequency.

In programmable channel selective user must set up center frequency, nanoSAW repeaters are

a special case of programmable selective repeater, where number of channels is equal to one.

For both types of repeaters user could set up start, stop or center frequency either using

absolute values (in MHz) or using ARFCN.

For fixed bandwidth repeaters this feature will not allow user to make changes, so, skip this step

for fixed bandwidth models.

2. Setup desired operating gain using pFOMS. UL and DL chain are independent, so both

values must be set.

For nominal gain of the repeater these values must be set to zero.

Figure 3

Figure 3 shows how to set up manual attenuation values.

UM-0101-01.09 – November 2009

Status Indicators

There is an indicator panel located at the front of the repeater. This led panel works as a status

monitor, in order to advice different operational conditions of the repeater.

1. Power indicator

Every time the repeater is plugged to DC power supply, and under normal conditions of

operation, led labelled PWR ON will be ON.

Figure 4

Figure 4 shows PWR ON led location.

2. Automatic Gain Control Indicator

When Automatic Gain Control circuitry is active led labelled AGC UL and/or AGC DL will be ON.

Please see Automatic Gain Control for further functional explanation.

Figure 5

Figure 5 shows AGC DL led active, this is only for example purposes.

3. Overload Indicator

When Overload circuitry is active led labelled OV DL or OL UL will be ON.

Please see Overload Protection for further functional description.

Figure 6

Figure 6 shows OL DL led active, this is only for example purposes.

Inhaltsverzeichnis

Andere Fiplex Repeater Handbücher

Fiplex

Fiplex A1 Bedienungsanleitung

Fiplex

Fiplex UHF Compact Leitfaden

Beliebte Repeater Handbücher anderer Marken

Gigaset

Gigaset 108 Bedienungsanleitung

Ace TECHNOLOGY

Ace TECHNOLOGY USR-1900A Bedienungsanleitung

Kenwood

Kenwood TKR-750-850 Stücklistenhandbuch

Asus

Asus RP-AC51 Bedienungsanleitung

Exibel

Exibel HRP0101 Bedienungsanleitung

Kidde

Kidde Vega Bedienungsanleitung

Telcosat

Telcosat RBB 850 Installationsanleitung

York

York Universal LINC485 Bedienungsanleitung

MIKOM

MIKOM MRx01B Power Series Bedienungsanleitung

Simrad

Simrad RD 301 Bedienungsanleitung

Tait

Tait TB7304 Bedienungsanleitung

R-tron

R-tron RSN-CDMA-37-C Bedienungsanleitung

Inventronics

Inventronics DALI REPEATER SO Bedienungsanleitung

XFP

XFP 16 Bedienungsanleitung

Andrew

Andrew MRx18 Bedienungsanleitung

COMBA

COMBA RXA3748 Bedienungsanleitung

ADRF

ADRF SDR-ICS-43 Bedienungsanleitung

Teltonika

Teltonika WRP100 Bedienungsanleitung

Fiplex nanoSAW Series Bedienungsanleitung

Beliebte Repeater Handbücher anderer Marken