FireAngel WTSL-SN-1 Bedienungsanleitung

Installation and User Guide

For use with Wi-Safe 2 Smoke, Heat and Carbon Monoxide Alarms

WTSL-SN-1 Alarm Control Unit with Wi-Safe 2®

Sprue Safety Products Ltd. Vanguard Centre, Coventry CV4 7EZ UK

GN3019R6

Email: specication@reangeltech.com / Web: www.reangel.co.uk

Technical Support Line: 0800 171 2009

PLEASE READ THIS GUIDE IN FULL BEFORE USING YOUR WTSL-SN-1 ALARM

CONTROL UNIT!

This user guide is also available in large text and other formats.

Please call 0800 171 2009 for further information.

Battery powered Alarm Control Unit with Test, Silence, Locate function. Non-replaceable 3V

DC battery.

W2 module contained within WTSL-SN-1 independently tested to RF standard

EN 301 489-1 V1.9.2, EN 301 489-3 V1.6.1, EN 300 220-2 V3.1.1

Frequency: 868MHz

With the present declaration, Sprue Safety Products Ltd conﬁrms that the WTSL-SN-1 conforms to the

essential requirements and other relevant measures of the 2014/53/EU Directive.

The Declaration of Conformity can be accessed on the website: http://spru.es/EC-WTSL-SN-1

Features . . . . . . . . . . . . . . . . 4

Positioning . . . . . . . . . . . . . . 6

Installation. . . . . . . . . . . . . . . 6

Wireless Interlink . . . . . . . . . . . 8

Making the Alarm Control Unit

Tamper Proof . . . . . . . . . . . . .10

INSTALLATION GUIDE

Testing the Alarm System . . . . . .12

Product Functionality . . . . . . . . .13

Reorganising a Network . . . . . . .16

When an Alarm Sounds . . . . . . .17

LED Indicators. . . . . . . . . . . . .18

Troubleshooting. . . . . . . . . . . .20

Maintenance. . . . . . . . . . . . . .22

Disposal . . . . . . . . . . . . . . . .23

Warranty . . . . . . . . . . . . . . . .23

USER GUIDE

Email: specication@reangeltech.com / Web: www.reangel.co.uk

Technical Support Line: 0800 171 2009

FEATURES

• Wi-Safe 2®technology, enabling wireless interlinking between other Wi-Safe 2 products.

• Test / Silence ( ) button, allowing you to regularly test all wirelessly interlinked alarms on

a network. Pressing the silence button will reduce the sensitivity of alarms for up to 10 minutes,

unless carbon monoxide has been detected, in which case you can use the 'Locate' function below

to ﬁnd the source alarm.

• Locate button ( ), allowing you to silence all alarms but the initiating alarm, during an alarm

condition. During a fault condition, this feature will allow you to locate the alarm in fault, in a

similar way.

• Alarm memory function - allows you to investigate previous alarm events.

• 10 year sealed for life battery.

• 5 year warranty.

INSTALLATION GUIDE

Test / Silence button Locate button

Carbon monoxide

alarm indicator Smoke / Heat

alarm indicator

Fault indicator

POSITIONING

This Alarm Control Unit is suitable for use in domestic premises only. It should be installed at an

accessible point on the wall, in a location where it will not be accidentally operated or knocked.

INSTALLATION

• Ensure this Alarm Control Unit is installed by a competent person who feels able to install it

according to the instructions.

• Read all installation instructions prior to installing this product.

WARNING: To prevent injury, this Alarm Control Unit must be securely attached to the wall in

accordance with the installation instructions.

To mount the bracket onto a wall:

Please ensure that you use the screws provided, as they were chosen speciﬁcally for use with this

product. Drill holes into the wall and insert supplied wall plugs. Screw the bracket in place.

ACTIVATING THE ALARM CONTROL UNIT

The Alarm Control Unit has a sealed-in non-

replaceable battery. To activate the control unit

remove the disabling tab.

Upon activating the control unit all three LED's

should simultaneously ﬂash twice, to indicate

that they are working.

Once the alarm is activated it can then be learnt

into a Wi-Safe 2 network, before securing to the

wall bracket.

WIRELESS INTERLINK

The Alarm Control Unit is designed to be used as a remote interface on a network of up to 49 products

within the Wi-Safe 2 range. The Alarm Control Unit can be used to test, silence or locate any alarms

on the Wi-Safe 2 network. It is not designed to communicate with wireless alarms from other ranges

or manufacturers. The control unit needs to be ‘learned-in’ or interlinked, in order to communicate

within the network.

Wi-Safe2 enables wireless communication with any other product with Wi-Safe2 technology inside.

When one alarm detects smoke / heat / carbon monoxide, the wireless module inside sends a signal

to all the connected alarms, ensuring almost instantaneous reaction across the network.

Wireless Interlink

Wi-Safe 2

enabled device

Wi-Safe 2

Alarm Control Unit

Learn button

LED

HOW TO ‘LEARN-IN’ THE ALARM CONTROL

UNIT TO A WI-SAFE 2 NETWORK:

1. Using a ballpoint pen, brieﬂy push and

release the 'learn button' on the back of the

control unit. The red LED next to the learn

button will ﬂash brieﬂy then light up for

approximately 5 seconds.

2. During these 5 seconds you need to brieﬂy

press the test button on an alarm already in

the network, to wirelessly interlink the two.

The alarm will sound its audible test pattern.

3. The red LED on the back of the control

unit will ﬂash to indicate that it has been

‘learned-in’ successfully. If the test button

is not pressed quickly enough, the ‘learn-

in’ process will fail. If this happens, repeat

the process.

Your Alarm Control Unit counts as one unit within

the network. If it is installed retrospectively, then

the existing network cannot exceed 49 units in

size.

4. To complete the installation simply slide the

control unit onto the bracket.The control unit

is now part of the whole network.

The method above assumes you have already

installed your alarm network, prior to installing

your Alarm Control Unit. If you want to install

your Alarm Control Unit ﬁrst, you can learn your

smoke, heat and CO alarm into it by following

the instructions in your alarm manual, using the

Alarm Control Unit as alarm 1.

MAKING THE ALARM

CONTROL UNIT TAMPER

PROOF

Do not complete this action until you have

wirelessly interlinked all of your alarms.

Inhaltsverzeichnis

Andere FireAngel Steuereinheit Handbücher

FireAngel

FireAngel ZW-MODULE Bedienungs- und Wartungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung