FireAngel ST-620 Thermoptek Bedienungsanleitung

User Manual

SMOKE ALARM

10YEAR LIFE

ST-620

EN 14604:2005

KM 557789

Sprue Safety Products Ltd.

Vanguard Centre, Sir William Lyons Road, Coventry CV4 7EZ UK

A Sprue Safety Products Brand

Technical Support: 0800 141 2561

EIRE dial: 1-800 523171

Email: tec[email protected]

Web: www.ﬁreangel.co.uk

ST-620

GN0681R5

0086

0086-CPR-557790

Smoke alarm devices

EN 14604:2005

DOP: SADOPST-620-03

Introduction . . . . . . . . . . 4

Automatic Power Engage . . 4

Thermoptek Sensor

Technology . . . . . . . . . . 4

Positioning . . . . . . . . . . 4

How to InstallYour Smoke

Alarm . . . . . . . . . . . . . 6

CONTENTS

NOTE: This user manual is also available in large

text and other formats. Please call 0800 141 2561

for further information.

Operation . . . . . . . . . . . 7

AlarmTest . . . . . . . . . . . 8

Alarm Smart Silence™ . . . . 8

Troubleshooting. . . . . . . .10

Maintenance. . . . . . . . . .11

Disposal . . . . . . . . . . . .12

Warranty . . . . . . . . . . . .12

typical response time to fast ﬂaming ﬁres

signiﬁcantly.

Thermoptek alarms are “toast-proof”

meaning they can be positioned in area

close to kitchens that may be affected by

cooking fumes. Heat alarms should be used

in kitchens where required.

POSITIONING

WARNING: Your smoke alarm can be

installed into a new build property as

additional protection to an existing smoke

detection system only. It cannot be used

as a substitute for a hard wired system as

required in new build properties. In this

type of property the building regulations

require alarms to be interlinked. You can

obtain further information from your local

ﬁre service or building control department

at your local council ofﬁces. These sources

generally provide advice on new builds or

projects that require planning permission.

Your smoke alarm typically meets the

minimum requirements for family living

units in existing buildings, as long as at

least one unit is installed on each ﬂoor/level

of your property.

In order to achieve the earliest ﬁre warning,

we recommend that a smoke alarm is

ﬁtted in all rooms where the temperature

is normally between 4°C (40°F) and 38°C

(100°F). Check that the smoke alarm is

correctly positioned for the particular

dwelling into which it is intended to be

installed.

INTRODUCTION

IMPORTANT: This user manual contains

important information regarding the

operation of your smoke alarm. Ensure you

read this user manual fully before installing

and operating the alarm. If you are installing

this smoke alarm for use by others, you

must leave this manual (or a copy of it) with

the end user.

AUTOMATIC

POWER ENGAGE

Your 10 year life smoke alarm is powered

by an internal lithium power pack. To avoid

unnecessary use of the power pack prior to

installation, and to ease disposal when the

alarm reaches the end of its life, the alarm is

supplied with the power pack in a deactivated

state. The power pack is automatically

enabled when the alarm is fully locked on to

the base plate.

IMPORTANT: Your alarm will not work until

it is correctly located and secured on the

base plate.

THERMOPTEK SENSOR

TECHNOLOGY

This combines an optical sensing chamber

with thermal enhancement. The alarm is

effective at detecting slow burning ﬁres, and

constant monitoring of temperature changes

enables the sensitivity of the alarm to be

instantly increased thereby quickening the

LOUNGECELLARBEDROOMBEDROOMHALLDINING ROOMMINIMUM RECOMMENDATIONSEXISTING HOMES

NOTE:

Kitchens should be covered by a self contained heat detector.RECOMMENDED FOR ADDITIONAL PROTECTION

typical response time to fast ﬂaming ﬁres

”

meaning they can be positioned in area

fected by

Heat alarms should be used

WARNING: The alarm positions shown

below are based on typical homes.

Construction and layout of individual

dwellings will vary, so this should be

regarded only as a guide. Check with your

local ﬁre station for further guidance.

LOUNGECELLARBEDROOMBEDROOMHALLDINING ROOMMINIMUM RECOMMENDATIONSEXISTING HOMESNOTE: Kitchens should be covered by a self contained heat detector.RECOMMENDED FOR ADDITIONAL PROTECTIONMulti-family or mixed occupant

residence (Tenancy building, student

accommodation)

Your smoke alarm can also be used in

individual ﬂats and bedsits, providing the

same conditions are met as for a single-

family residence. However, there must

already be a primary ﬁre detection system

that meets regulatory requirements

for common areas such as lobbies and

hallways.

Institutions and Hotels

This includes motels, hospitals, day care

facilities, long-term health care facilities,

boarding houses and dormitories. Your

smoke alarm can be used in individual

sleeping/resident rooms, providing the

same conditions are met as for a single-

family residence. However, there must

already be a primary ﬁre detection system

that meets regulatory requirements

for common areas such as lobbies and

hallways. Use of this smoke alarm in

common areas may not provide sufﬁcient

ﬁre warning to residents or meet regulatory

requirements.This smoke alarm is designed

to operate as a standalone smoke alarm.

WARNING: This smoke alarm will not

communicate with other smoke alarms or

ﬁre alarm systems. It is not intended as a

substitute for a complete alarm system.

Mobile Homes and Caravans

This smoke alarm is suitable for use in

mobile homes and caravans.

Commercial and Industrial Premises

This smoke alarm is not intended for any

non-residential, commercial or industrial

application, nor for any other purpose than

described above.

HOW TO INSTALL

YOUR SMOKE ALARM

IMPORTANT: Make sure you have read and

understood this manual before installing

your smoke alarm.

1 Preparation

The base plate should be attached to the

ceiling or wall.

Base plate tabs

Break out the tabs from the base plate. Use

the ﬁxing slots on the base plate as a guide

when marking the position of the drill holes.

With an appropriately sized drill, drill the

holes and insert the plastic ﬁxing anchors

supplied (if needed).

2 Install Base Plate

Fit the base plate to the ceiling or wall using

the screws provided.

3 FitYour Smoke Alarm

The alarm has a mechanism on the back

that activates the alarm when it is correctly

connected to the base plate.

Alarm Base Plate

Lugs (hooks)

There are three lugs (hooks) on the back of

the alarm that slide in to three slots on the

base plate.The alarm can be attached in any

orientation, simply line up the lugs (hooks)

with the holes at the end of the slots then

twist the alarm clockwise until the alarm

stops, make sure the alarm is twisted on

fully.

Once the smoke alarm has been ﬁtted onto

the base plate correctly, the internal power

pack will activate. The red LED on the front

of the alarm should now ﬂash once every 40

seconds to show that it is active.

4 TestYour Smoke Alarm

After ﬁtting the alarm to the base plate, wait

for 5 seconds for the alarm to settle then

test the alarm. See ‘AlarmTest’.

all using

Alarm Base Plate

OPERATION

Normal condition

The red LED on the front should ﬂash every

40 seconds to show that the alarm is active.

Low Power Pack Condition

IMPORTANT: Your smoke alarm requires

the power pack to have sufﬁcient capacity of

power to operate correctly.

Should your smoke alarm enter a low

power pack condition, the unit will emit an

audible ‘chirp’ once every 40 seconds. When

this occurs you must replace the alarm

immediately.Your smoke alarm will continue

to warn of this low power pack condition for

at least 7 days, however, failure to change

the alarm after this time would mean your

smoke alarm may have insufﬁcient power

to alert you in a real ﬁre situation. When the

alarm is removed from the base plate the

power pack will automatically deactivate and

the low power warning chirp should stop,

allowing you to dispose of the alarm.

ALARM TEST

The alarm must be properly attached to the

base plate before it can be tested.

a Press the test button in the centre and

release.

b The unit will give an audible alarm

consisting of 2 cycles of 3 loud beeps,

then stop automatically.

c The red LED on your alarm will ﬂash

rapidly during the audible signal.

NOTE: The test button accurately tests

the alarm’s smoke sensing circuit, there is

no need to test your alarm with smoke. If

your smoke alarm fails to give an audible

test signal, please refer immediately to the

Troubleshooting section at the end of this

manual.

WARNING: As with all electronic alarm

products you should test your smoke alarm

every week.

ALARM

SMART SILENCE™

DANGER: If your smoke alarm emits the

full alarm signal and you are not testing the

unit, the smoke alarm is warning you of a

potentially dangerous situation that requires

your immediate attention. Only use the

alarm silence function after making sure that

there is no ongoing ﬁre emergency situation.

Do not block the vents on the alarm or

disable the smoke alarm in any way, as this

will remove your protection. Smoke alarms

can sometimes react to cooking fumes or

other non emergency situations.Your smoke

alarm features “Smart Silence” technology.

In the event of a known false alarm your

smoke alarm can be temporarily silenced by

pressing the central test button. Your alarm

will automatically return to full sensitivity

within 10 minutes.

NOTE: If the level of smoke reaching the

alarm is very high the alarm silence will be

overridden and the alarm will continue to

sound.

a Press and release the silence button, the

alarm sound will shortly stop.

b Your alarm will silence and enter into

a reduced sensitivity reset cycle for

approximately 10 minutes.

c During the reduced sensitivity reset cycle,

the red LED on your alarm will continue

to ﬂash more rapidly than normal,

approximately once every second.

d Your alarm will automatically return

to full sensitivity on completion of the

reset cycle and the red LED will revert to

ﬂashing once every 40 seconds.

DANGER: Never ignore any alarm. Ignoring

the alarm may result in injury or death. If

your smoke alarm activates and alarms and

you are not absolutely certain of the source

of the smoke, get everyone out of the house

immediately.

ton accurately tests

e sensing circuit, there is

audible

test signal, please refer immediately to the

roubleshooting section at the end of this

alarm

e alarm

e alarm emits the

full alarm signal and you are not testing the

arning you of a

potentially dangerous situation that requires

Only use the

ter making sure that

k the vents on the alarm or

, as this

e alarms

can sometimes react to cooking fumes or

TROUBLESHOOTING

Problem Solution

Your smoke alarm

does not sound

during testing

• Make sure the alarm has been rotated clockwise as far as it can go

and is securely located on base plate (this means the power pack

has been activated). If testing immediately after ﬁrst activating the

alarm you should allow a few seconds for the alarm to settle before

testing.

• Make sure you push the centre of the test button ﬁrmly.

• If the unit has been silenced and is in low sensitivity mode it may

not test. Wait 15 minutes then try again.

• If the alarm has been recently ﬁtted and it still fails to self test then

contactTechnical Support.

Your smoke alarm

chirps intermittently

• Check the location of your smoke alarm (see ‘Positioning’).

• Check that your smoke alarm is deﬁnitely the source of chirping;

make sure the noise isn’t coming from another alarm (smoke /

carbon monoxide / burglar / gas alarm) by process of elimination.

• If positioned correctly, and the smoke alarm is the source of the

chirping, this indicates that there is a fault with the alarm. If within

warranty contact Technical Support, otherwise replace immediately.

Your smoke alarm

chirps every 40

seconds

• This indicates that the power pack (battery) is low. If within warranty

contact Technical Support, otherwise replace immediately.

Your smoke alarm

activates when no

smoke is visible

• Check the location of your smoke alarm (see ‘Positioning’).

• Clean the smoke alarm (see ‘Maintenance’).

You experience

frequent unwanted

alarms

• Check the location of your smoke alarm (see ‘Positioning’).

• Clean the smoke alarm (see ‘Maintenance’).

• If the frequent unwanted alarms continue contactTechnical Support

for advice.

If you have any further questions about the operation of your alarm, please contact

Technical Support between 9am - 5pm Monday – Friday. Telephone: 0800 141 2561 or

e-mail: tec[email protected] You can also visit the support section of our website

www.ﬁreangel.co.uk

Andere Handbücher für ST-620 Thermoptek

Inhaltsverzeichnis

Andere FireAngel Rauchmelder Handbücher

FireAngel

FireAngel THERMOPTEK ST-623E Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-625 Bedienungsanleitung

FireAngel

FireAngel THERMOPTEK ST-623E Bedienungsanleitung

FireAngel

FireAngel SI-610 Bedienungsanleitung

FireAngel

FireAngel ST-230 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel THERMOPTEK Wi-Safe 2 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622-T Bedienungsanleitung

FireAngel

FireAngel LSI-601 Bedienungsanleitung

FireAngel

FireAngel THERMISTEK HT-630 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel P-LINE HT-630 Montage- und Bedienungsanleitung

FireAngel

FireAngel ST-630-INT Bedienungsanleitung

FireAngel

FireAngel THERMISTEK HT-630 Bedienungsanleitung

FireAngel

FireAngel EZ-212 Bedienungsanleitung

FireAngel

FireAngel ST-750 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-625 Bedienungsanleitung

FireAngel

FireAngel THERMISTEK HT-630 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel SI-601 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

FireAngel

FireAngel ST-623E-INT Bedienungsanleitung

FireAngel

FireAngel Wi-Safe 2 Thermoptek WST-630-NEU Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung

Radal Technology

Radal Technology Cig-Arrête CSA-POD Bedienungsanleitung