Firegear ANF-R42 Bedienungsanleitung

AnF “Assemble-n-Finish” Fire Pit Enclosures

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS

DO NOT ATTEMPT TO ASSEMBLE OR INSTALL THIS PRODUCT

Warning:

Outdoor Use Only

Warning:

Outdoor Use Only

INSTALLATION PRECAUTION:

These enclosures requires a minimum 18-square inches of cross ventilation per

installed burner. Failure to provide proper ventilation can void the warranty.

ANF-R42 42” x18” enclosure  ts FPB-16R/19R & FPB-20S

ANF-R48 48”x18” enclosure  ts FPB19R/25R or FPB20S/26S

ANF-R60 60”x18” enclosure  ts FPB-25R/29R/33R or FPB26S/32S/38S

ANF-L48 48”x 24”x 18” enclosure  ts FPB-24L/30L/36L

ANF-L66 66”x24”x18” enclosure  ts FPB-24L/30L/36L or (2) FPB-24L (end to end)

ANF-L74 74”x 24”x18” enclosure  ts FPB-24L/30L/36L or (2) FPB-24L or (2) FPB-30L (end to end)

ANF-L90 90”x 24” x 18” enclosure FPB-24L/30L/36L or (2) FPB-24L or (2) FPB-30L (end to end)

or (2) FPB-36L (end to end)

ANF-S48 42”x 42” x 18” enclosure  ts FPB-19R/25R, FPB-20S/26S

ANF-S60 60”x 60”x 18” enclosure  ts FPB-25R/29R/33R or FPB-26S/32S/38S

Model Description

AnF “Assemble-n-Finish” Fire Pit Enclosures

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE

CALIFORNIA PROPOSITION 65

WARNING

This product can expose you to Chromium, which is

known to the state of California to cause cancer

and birth defects or other reproductive harm.

(For more information, go to www.p65warnings.ca.gov)

AnF Enclosures REV. 8-29-18 Page 2

Contents of Enclosure

Each quarter section has a 90-degree inner ﬂ ange on one side (See Fig. 2 - arrows). Butt the inner

ﬂ ange of one other quarter section to the non-ﬂ ange side of another section (See Fig 3).

(4) Quarter Sections

(4) 45° Pan Supports

Fig. 1 Round

AnF Contents

(4) MgO Boards (1) Vent-Kit-6x12

Round AnF Enclosure Assembly

Two people are recommended to assemble all enclosures. It is also recommended to assemble the

enclosure on a ﬂ at surface. The assembly of the AnF should be done at or near the location of the

installation.

Leveling Legs (16) Self Tapping Screws (16) Cement Board Screws

AnF-R42 & AnF-R48: 4 Legs

AnF-R60: 8 Legs

STEP 1

Remove all parts and make sure that you have received all necessary pieces.

It is important to start the assembly process with the quarter sections upside-down. To make sure the

quarter pieces are upside down, the bottom side has a nutsert (See Fig 2 - circle). The nutsert needs

to be facing upward on each quarter section.

Fig. 2 Nutsert + 90° Flange

Fig. 3 Lining Up Sides

*ANF-R42 and ANF-48 ONLY!

Remove all parts and make sure that you have received all necessary pieces.

(2) Horizontal Pan Supports

*ANF-60 ONLY!

NOTE

AnF Enclosures REV. 8-29-18 Page 3

Fig. 4 Installing Self-Tapping Screws Into Quarter Pieces

While the assembled quarter sections are still upside-down, install the leveling legs. Locate the

nutsert on the quarter sections (See Fig. 2). Take the leveling legs and screw them into the nutsert.

The legs should be screwed in until there is 1-inch of clearance between the top of the leg and the

quarter section (See Fig. 5).

Fig. 5 Installing Leveling Legs Into Quarter Pieces

After the leveling legs have been installed, carefully

ﬂ ip the entire AnF unit over so that it is resting on

the leveling legs.

NOTE: If you have an ANF-R60, you will have 8 leveling

legs to install.

Now that the quarter sections are put together, the feet are installed and the unit is turned over, the

pan supports are ready to be installed. Please note that this is a OPTIONAL feature only used for

speci c Firegear Outdoor models. The chart below shows which Fire Pit Burner models  t in each

model of AnF, and which ones require pan supports.

Once the AnF is turned over on the leveling legs, make

any adjustments to the legs to make sure the unit is

level. This must be done in the installation location.

After the two quarter sections are butt together,

secure them with self-tapping screws; one into the

inner hole at the top and one into inner hole at the

bottom of the two sections (See Fig. 4).

Before you completely tighten the screws, check for

squareness. Tighten screws.

Assemble the remaining sections the same manner.

STEP 2

STEP 3

16”

ROUND

19”

ROUND

20”

SQUARE

25”

ROUND

26”

SQUARE

29”

ROUND

32”

SQUARE

33”

ROUND

ANF-R42 Does this pan ﬁt this AnF? YES YES YES NO NO NO NO NO

Does it require supports? YES NO NO NO NO NO NO NO

ANF-R48 Does this pan ﬁt this AnF? NO YES YES YES YES NO NO NO

Does it require supports? NO YES YES NO NO NO NO NO

ANF-R60 Does this pan ﬁt this AnF? NO NO NO YES YES YES YES YES

Does it require supports? NO NO NO YES NO NO NO NO

We strongly recommend two

people when turning the AnF over.

AnF Enclosures REV. 8-29-18 Page 4

STEP 4

10mm MgO (Magnesium Oxide) Board is provided for the top surface. Each board comes with a

pre-marked template based on the most popular Firegear burners for the size of AnF enclosures

(See Fig. 8).

Place all (4) boards on top of the AnF. Mark where you need to cut following the template. For each

piece you will need to cut on the inside (for the pan) and the outside (for the edge of the AnF). Once

the pieces are cut, place them back on the top of the AnF and attach using the cement board screws

provided (See Fig. 9). You can install the cement board screws anywhere there is metal underneath

the MgO board top. (See Fig. 10).

Fig. 8 Round MgO Top Fig. 9 Round MgO Top Installed

Fig. 6 Installing 45° Pan Supports

Installing 45° Supports

Look at the AnF below and note how the pan

supports are installed. There are two pre-drilled

holes in the middle of each side (at the top - on

the inside) (See Fig. 6). These holes are used

for the 45° pan supports. Using the self tapping

screws, use two screws per pan support and

install them in the pre-drilled holes.

Installing Horizontal Supports

Look at the AnF below and note how the pan

supports are installed. Each of the quarter

sections have 4 holes at the top, 2 for each

support to be installed in (See Fig. 7). To

install, use the self sapping screws. Use four

screws per pan support and install them in the

pre-drilled holes.

Fig. 7 Installing Horizontal Pan Supports

Fig. 10 Cement Board Screws

AnF-R42 & R48 AnF-R60

AnF Enclosures REV. 8-29-18 Page 5

STEP 5

After the entire AnF is assembled, install the Vent-Kit-6x12. These vents are designed to be used

with the AnF Series as well as universal vents for many other types of  re pit enclosures. Look at the

contents provided to ensure you have received everything correctly.

(2) Vents (12) Phillips Black

Pan Head Screw

(12) Stainless Steel

Nut

(2) Stainless Steel

Flat Washer

Install the vents on opposite sides of the enclosure to ensure cross ﬂ ow ventilation. Cross ﬂ ow

ventilation is necessary to provide free ﬂ owing air to assist in keeping the enclosure dry and cool

during operation of a  re pit.

Cut an rectangular opening 9.750”w x 3.750”h

into on opposite sides of the enclosure. Center

the vent over the cut out area ensuring the vent

slots are clear of any obstruction. Mark the holes

with a pencil or marker. Drill six 1⁄4” pilot holes,

position the vent centered over the opening,

insert a screw into the vent and enclosure at

the same time and secure with washer and nut

on the inside. Repeat the process until all six

screws are securing each vent into place on

both sides of the AnF enclosure (See Fig. 11). 9.750”

3.750”

CUT OUT DETAIL

Fig. 11 Vent Cut Out Dimensions

NOTE: Before cutting the rectangular opening

for your vents, be sure that you are not hitting

one of the metal studs inside the AnF. The vents

must be directly across from each other.

AnF Enclosures REV. 8-29-18 Page 6

(2) Side Panels

(2) Pan Supports

Fig. 12 Linear AnF Contents

(2) Side Panels

(2) MgO Boards (1) Vent-Kit-6x12

(16) Self Tapping Screws (16) Cement Board Screws

It is important to start the assembly process with the panels upside-down. Ensure the panels are

upside down, the bottom side has a nutsert (See Fig 13 - Circle). The nutsert needs to be facing

upward on each panel. Each panel also has a 90° inner ﬂ ange on one side (See Fig. 13 - Arrows).

(2) End Panels

Linear AnF Enclosure Assembly

Contents of Enclosure

Two people are recommended to assemble all enclosures. It is also recommended to assemble the

AnF enclosure on a ﬂ at surface. Assembly of the AnF should be done at or near the location of the

installation.

Remove all parts and make sure that you have received all necessary pieces.

NOTE

STEP 1

Fig. 13 90° Flange + Nutsert

Leveling Legs

AnF-L48 & AnF-L66: 6 Legs

AnF-L74 & AnF-L90: 8 Legs

(2) Side Panels

Remove all parts and make sure that you have received all necessary pieces.

AnF Enclosures REV. 8-29-18 Page 7

While the panels are still upside-down, install the leveling legs. Locate the nutsert on the panels (See

Fig. 11). Take the leveling legs and screw them into the nutsert. The legs should be screwed in until

there is 1- inch of clearance between the top of the leg and the panel (See Fig. 16).

Fig. 16 Installing Leveling Legs Into Panels

After the leveling legs have been

installed, carefully ﬂ ip the entire AnF

unit over so that it is resting on the

leveling legs.

NOTE: If you have an ANF-74 or ANF-90, you will have 8 leveling legs to install.

Once the unit is turned over on the

leveling legs, make any adjustments to

the legs to make sure the unit is level.

This must be done on the installation

location.

Butt the inner ﬂ ange of one of the panels to the non-ﬂ ange side of another panel (See Fig. 13).

After the two ends are butt together, secure

them with self-tapping screws; one into the

inner hole at the top and one into inner hole at

the bottom of the two panels (See Fig. 15).

Before you completely tighten the screws,

check for squareness. Tighten screws.

Assemble the remaining sections the same

manner.

Fig. 14 Butting Ends Together

Fig. 15 Installing Self-Tapping Screws Into Panel

STEP 2

We strongly recommend two people

when turning the AnF over.

AnF Enclosures REV. 8-29-18 Page 8

Fig. 17 Pan Support Placement Fig. 18 Install Pan Supports

If you are using a Firegear Burner System, you MUST install the supports for the AnF.

Every Linear Burner System requires supports.

STEP 4

10mm MgO (Magnesium Oxide) Board is provided for the top surface. Each board comes with a pre-

marked template based on the most popular Firegear burners for the size of AnF enclosures (See

Fig. 19).

Place both boards on top of the AnF. Mark where you need to cut following the template. For each

piece you will need to cut on the inside in order to  t the burner type. Once the pieces are cut, place

them back on the top of the AnF and attach using the cement board screws provided (See Fig. 20).

Fig. 19 Linear MgO Top Fig. 20 Linear MgO Top Installed

In order to attach the cement board screw securely, you must screw them into the metal edges or

supports of the AnF. Measure 1 inch from the edge of the AnF and drill into the metal through the

MgO board. You can also drill into the supports that hold the pan in place.

STEP 3

Now that the panels are put together, the feet are installed and the unit is turned over, the pan

supports are ready to be installed.

There are 2 pre-drilled holes on each END panel. See Figure 17 - it shows how the pan supports

should be placed. Using the four pre-drilled holes, place the pan supports in their appropriate spots.

Using the self tapping screws, install them in the pre-drilled holes on each side (See Fig. 18).

AnF Enclosures REV. 8-29-18 Page 9

STEP 5

After the entire AnF is assembled, install the Vent-Kit-6x12. These vents are designed to be used

with the AnF Series as well as universal vents for many other types of  re pit enclosures. Look at the

contents provided to ensure you have received everything correctly.

Install the vents on opposite sides of the enclosure to ensure cross ﬂ ow ventilation. Cross ﬂ ow

ventilation is necessary to provide free ﬂ owing air to assist in keeping the enclosure dry and cool

during operation of a  re pit.

Cut an rectangular opening 9.750”w x

3.750”h into on opposite sides of the

enclosure. Center the vent over the cut out

area ensuring the vent slots are clear of any

obstruction. Mark the holes with a pencil

or marker. Drill six 1⁄4” pilot holes, position

the vent centered over the opening, insert

a screw into the vent and enclosure at the

same time and secure with washer and

nut on the inside. Repeat the process until

all six screws are securing each vent into

place on both sides of the AnF enclosure

(See Fig. 21).

CUT OUT DETAIL

9.750”

3.750”

Fig. 21 Vent Cut Out Dimensions

(2) Vents (12) Phillips Black

Pan Head Screw

(12) Stainless Steel

Nut

(2) Stainless Steel

Flat Washer

NOTE: Before cutting the rectangular

opening for your vents, be sure that you are

not hitting one of the metal studs inside the

AnF. The vents must be directly across from

each other.

AnF Enclosures REV. 8-29-18 Page 10

(2) Pan Supports

Fig. 22 Linear AnF Contents

(4) MgO Boards

(1) Vent-Kit-6x12

(4) Leveling Legs

(16) Self Tapping Screws (16) Cement Board Screws

STEP 1

(4) Side Panels

Square AnF Enclosure Assembly

Contents of Enclosure

Two people are recommended to assemble all enclosures. It is also recommended to assemble the

enclosure on a ﬂ at surface. The assembly of the AnF should be done at or near the location of the

installation.

Remove all parts and make sure that you have received all necessary pieces.

NOTE

It is important to start the assembly process with the panels upside-down. Ensure the panels are

upside down, the bottom side has a nutsert (See Fig 23 - Circle). That nutsert needs to be facing

up on each panel. Each panel also has a 90° inner ﬂ ange on one side (See Fig. 23 - Arrows).

Fig. 23 90° Flange + Nutsert

Dieses Handbuch passt für folgende Modelle

Andere Firegear Außenkamin Handbücher

Firegear

Firegear LOF-2412HAWS-N Handbuch

Firegear

Firegear PRO Series Bedienungsanleitung

Firegear

Firegear KWB-NG1 Kurzanleitung

Firegear

Firegear FPB-19RBSMT-N Bedienungsanleitung

Firegear

Firegear FPB-20SBSAWS-N Bedienungsanleitung

Firegear

Firegear LOF-30MT Bedienungsanleitung

Firegear

Firegear FPB-19DSI/N Bedienungsanleitung

Firegear

Firegear FPB-26DBS22TPSI-N Bedienungsanleitung

Firegear

Firegear VENT KIT 6x12 Bedienungsanleitung

Firegear

Firegear FPB-G34DBSMT-N Bedienungsanleitung

Firegear

Firegear OFP-36LECO-P Bedienungsanleitung

Firegear

Firegear FPB-29RBSAWS-N Bedienungsanleitung

Firegear

Firegear LOF-2412HTPSI-N Bedienungsanleitung

Firegear

Firegear FPB-20DBSMT-N Bedienungsanleitung

Firegear

Firegear LOF-36MTN Bedienungsanleitung

Firegear

Firegear OFP-36LECO-PLED Bedienungsanleitung

Firegear

Firegear LOF-2414FHMT-N Bedienungsanleitung

Firegear

Firegear FPB-24LTFS-N Bedienungsanleitung

Firegear

Firegear Kalea Bay OFP-36LECO-N Bedienungsanleitung

Firegear

Firegear FPB-G25RBSTFS-N Bedienungsanleitung

Firegear

Firegear LOF-4214HMT-N Bedienungsanleitung

Firegear

Firegear FG-H-2406SS Bedienungsanleitung

Firegear

Firegear LOF-2408FTTPSI-N Bedienungsanleitung

Firegear

Firegear FPB-32SFBSAWS-N Bedienungsanleitung

Beliebte Außenkamin Handbücher anderer Marken

Outdoor Plus

Outdoor Plus PISMO OPT-2448 Bedienungsanleitung

Legacy

Legacy Fire Pit Bedienungsanleitung

Coleman

Coleman 5055-710 Bedienungsanleitung

Jensen

Jensen 300NG Bedienungsanleitung

FEUERHAND

FEUERHAND PYRON Bedienungsanleitung

Classics

Classics FP35077 Bedienungsanleitung

Jensen

Jensen 1590LP Bedienungsanleitung

Mayer Barbecue

Mayer Barbecue HEIZA MFK-220 Bedienungsanleitung

Costway

Costway NP11018 Bedienungsanleitung

Target

Target Foxborough Bedienungsanleitung

Blumfeldt

Blumfeldt Merano Bedienungsanleitung

Blooma

Blooma Brasero Ulong Bedienungsanleitung

The Fireplace

The Fireplace JETMASTER 700 D Bedienungsanleitung

Superior

Superior VRE4543EN Bedienungsanleitung

Morsø

Morsø Forno Bedienungsanleitung

dobar

dobar CONICO 35439E Bedienungsanleitung

EAST OAK

EAST OAK GFT22001 Bedienungsanleitung

Napoleon

Napoleon PATIOFLAME GPFN Bedienungsanleitung