Firestone SIERRA Bedienungsanleitung
SIERRA
Fireplace
OWNER’S MANUAL
INSTALLATION INSTRUCTIONS
2
Contents__________________________
Contents……………………………….…………2
Required Tools….……………………………….3
Unwrapping.……………………………………..4
Removal of Firebox…..…………..…………..….5
Placing the Unit……………….....………………6
Installing the Firebox…………………..………..7
Installing the Top………………....……………..8
Planning the Gas Line…………………………...9
Locating the LPG Tank………...………………10
Installing the Hearth Pad.………………………11
Final Instructions / Dimensions…..…………….12
3
REQUIRED TOOLS
⇒ Razor Knife
• To cut and remove packaging.
⇒ Hammer or Pry Bar
• To remove 1 x 2 and staples.
⇒ Power Drill or Phillips Screw Driver
• To remove Packaging screws
⇒ Leather Gloves
• To protect hands from rough and sharp
items found on the Sierra Fireplace.
⇒ It is recommended that a minimum
of two people assemble and install
the Sierra Fireplace.
4
UNWRAPPING PROCEDURE
WARNING
THE CAST TOP AND HEARTH PAD
OF THE SIERRA IS NOT ATTACHED.
DO NOT SLIDE OR MOVE THE UNIT
UNTIL THESE ITEMS HAVE BEEN
REMOVED.
1. Carefully dissect the outside wrapping to
expose the unit. Maintain control of the
blade the product behind can be damaged.
2. Remove the 1 x 2’s so the unit is more eas-
ily removed from the pallet.
3. Remove the cast top and hearth pad with
a minimum of two people and set aside.
4. Remove the burner assembly from the fire-
box.
5
1. Remove all painted brown screws.
2. With a minimum of 2 people slide the fire-
box carefully and set aside. BE CAREFUL
NOT TO DROP THE UNIT DAMAGE
WILL OCCUR.
WARNING
FIREBOX WEIGHT IS 150-175 LBS.
REMOVAL OF THE FIREBOX
6
PLACING THE UNIT
FRAGILE
1. When moving the surround into place, be
careful not to damage the edges, they are
fragile.
2. THIS SHOULD BE MOVED WITH NO
LESS THAN TWO PEOPLE.
7
FIREBOX ASSEMBLY
1. Slide the Firebox slowly and at an even rate
back into its’ original position.
2. Re-attach the Firebox with the screws re-
moved on Page 5, Step 1.
8
TOP PLACEMENT
Place the top on the surround. The back
should be flush with the stone and centered.
9
PLANNING YOUR GAS LINE
Gas Line Inlet
The gas inlet into
the Sierra firebox
is located in the
back left corner.
Plan your gas line
accordingly.
The most convenient way to run your gas line
is up through the bottom. The bottom is open
and free of obstructions.
Back or side penetrations can be made by slid-
ing the firebox back out as discussed on Page
5 and with a 1” hole saw cut in your desired
location from inside of the unit to avoid struc-
tural supports.
10
LOCATING YOUR TANK
1. Your Sierra gas log is equipped for use
with either Natural Gas or Propane Gas.
Please confirm the type of gas you are
installing.
2. If your unit is intended to work on Pro-
pane Gas please adhere to all local and
national codes.
3. Locate your tank in a location that is ac-
cessible for service and easily shut off if
needed.
4. A pressure regulator should be used in
line before the unit is connected to the
pilot safety valve. ( This is not supplied.)
5. The inlet pressure to the pilot safety
valve is 11” W.C.
6. The size of your incoming line will limit
the distance you can place the tank from
the burner. See the chart below.
Pipe or
Tubing
Length
ft.
Tubing
3/8”
O.D.
Tubing
1/2”
O.D.
Sched-
ule 40
Pipe.
1/2”
Sched-
ule 40
Pipe.
3/4”
10 - OK OK OK
20 - OK OK OK
30 - - OK OK
40 - - OK OK
Inhaltsverzeichnis
Andere Firestone Kamin im Innenbereich Handbücher
