Fisher & Paykel WB60S Series Bedienungsanleitung

Warming Drawer

WB60S

models

NZ AU GB IE

INSTALLATION INSTRUCTIONS

590513E 05.16

www.ﬁsherpaykel.com

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our

website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

1SAFETY AND WARNINGS

WARNING!

Electrical Shock Hazard

Before carrying out any work on the

electrical section of the appliance,

it must be disconnected from the

mains electricity supply.

Connection to a good earth wiring

system is absolutely essential and

mandatory.

Alterations to the domestic wiring

system must only be made by a

qualified electrician.

Failure to follow this advice may

result in electrical shock or death.

WARNING!

Cut Hazard

Take care - panel edges are sharp.

Failure to use caution could result in

injury or cuts.

WARNING!

Fire hazard

Do not use adapters, reducers, or

branching devices to connect this

appliance to the mains power supply.

Failure to follow this advice may

result in overheating, burning, or fire.

IMPORTANT SAFETY INSTRUCTIONS!

 To reduce the risk of fire, electrical

shock, injury to person, or damage

when using the warming drawer,

please read these instructions

carefully before installing this product.

 Please make this information available

to the person installing the product –

doing so may reduce your installation

costs.

 Installation work, maintenance and

repairs may only be carried out by

suitably qualified and competent

persons in accordance with national

and local safety regulations.

 Always disconnect the power supply

prior to carrying out any installation,

maintenance or repair work.

 Before installation make sure that

the voltage and frequency listed on

the data plate corresponds with the

household electrical supply.

1SAFETY AND WARNINGS

 When installing companion products

the weight of the companion product

should be distributed across the edges

of the warming drawer. Products

above which rest on “feet” may only

be installed if the feet of the product

lie within 70mm of the sides of

the warming drawer, as this area is

reinforced. Failure to do this may result

in damage to the warming drawer and

companion product.

 Before installing the warming drawer

you must inspect it for any signs of

damage. Under no circumstances

should you install or use the warming

drawer if it has been damaged.

 If the power supply cord is damaged, it

must be replaced by the manufacturer,

its service agent or a similarly qualified

tradesperson in order to avoid a hazard.

 Connect the warming drawer to a

properly rated, protected and sized

power supply circuit to avoid electrical

overload.

 Do not use an extension cord or a

portable electrical outlet device (e.g.

multi-socket outlet box) to connect the

Warming Drawer to the power supply.

Make sure the power supply cord is

located so that it will not be stepped

on, tripped over or otherwise subject to

damage or stress.

 Ensure the connection to power supply

is accessible after installation.

IMPORTANT SAFETY INSTRUCTIONS!

 The electrical outlet should be easily

accessible after installation.

 When a companion product is installed

in combination with the warming drawer

to the same circuit, operating both

products may cause an overload. If in

doubt consult a qualified electrician.

 When installed in combination with

a companion product the companion

product may be placed directly onto

the warming drawer. It is not necessary

to place a shelf between the products.

A built- in shelf at the base of the

cabinetry able to support the weight of

both products is required.

 If installing the warming drawer directly

underneath an oven, ensure you do

not damage the oven’s lower trim. The

lower trim ensures correct air circulation

to the oven and allows the door to

open and close without obstruction.

Fisher & Paykel does not accept any

responsibility for any damage resulting

from incorrect installation.

 The maximum weight the warming

drawer is able to support is 60 kg.

 The warming drawer is not designed

for use in mobile installations such as

recreational vehicles, boats or aircraft.

3PRIOR TO INSTALLATION

 The cavity is square and level, and of the required dimensions.

 The installation will comply with all clearance requirements and applicable standards and regulations.

 The power switch will be easily accessible to the customer when the warming drawer is installed.

 The warming drawer (and any product on top of it) will rest on a surface that can support its weight.

 The height from the floor suits the customer.

 You consult local building authorities and by-laws if in doubt regarding installation.

If installing with a companion product

IMPORTANT!

 If installing with a companion product please refer to the installation instructions of that product to ensure the installation requirements of BOTH products are met.

 When installing products on top of the warming drawer, the weight of the product should be distributed across the edges of the warming drawer.

 Products above which rest on “feet” may only be installed if the feet of the product lie within 70mm of the sides of the warming drawer, as this area is reinforced.

Failure to do this may result in damage to the warming drawer and companion product.

Screws (4) Anti-tip bracket (1) Oven support brackets (2)

Warming Drawer can withstand

a maximum weight of 60kg

70mm 70mm

Feet

2PARTS SUPPLIED

F G

4PRODUCT DIMENSIONS

PLAN

FRONT

Terminal Block

SIDE

PRODUCT DIMENSIONS mm

AOverall height of product 118

BOverall width of product 596

CDepth of drawer front panel (excluding handle)* 19

DDepth of chassis (including terminal block) 536

EWidth of chassis at rear 551

FHeight from bottom drawer panel to bottom of chassis at rear 16

GHeight from bottom of drawer panel to top of chassis 118

HDepth of drawer (open) (measured from front of drawer) 455

IHeight of drawer front panel 116

JDepth of handle measured from front of drawer 41

KWidth of handle 565

5A CABINETRY DIMENSIONS - UNDERBENCH (IE INSTALLED WITH A F&P 60CM WIDE SINGLE OVEN)

720mm

Warming Drawer

Oven

*PO

Ta b

Oven support bracket

Fit the supplied oven support brackets

Unscrew-fit-

rescrew

THE FOLLOWING PAGES DETAIL COMMON CABINETRY SCENARIOS

IMPORTANT!

If installing under an oven, you must first fit the two

supplied Oven support brackets to the sides of the

Warming Drawer. The brackets help support the rear of

the oven.

Unscrew the 3 top screws on each side, fit the brackets

with the tabs facing inwards as shown and screw back in.

Note: The screws may not be identical.

Replace each screw into its original hole position.

Oven

support

brackets

PLAN

SIDE

CABINETRY DIMENSIONS mm

MMinimum inside height of cavity (with F&P 60cm wide single oven) 687

NInside width of cavity 560

OMinimum inside depth of cavity 565

Note: When installed in combination with a companion product the companion product may be placed directly onto the

warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able

to support the weight of both products is required.

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.

** In some instances the front cabinetry rail may need to be removed to enable installation.

5B CABINETRY DIMENSIONS - WALL MOUNTED (IE INSTALLED WITH A F&P COMPACT OVEN)

600mm

*PO

Ta b

Unscrew-fit-

rescrew

PLAN

SIDE

CABINETRY DIMENSIONS mm

MMinimum inside height of cavity

with optional Lower trim kit fitted

without optional Lower trim kit fitted

590

570

NInside width of cavity 560

OMinimum inside depth of cavity 565

Note: When installed in combination with a companion product the companion product may be placed directly onto the

warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able

to support the weight of both products is required.

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.

Compact Oven

Cabinet below

Additional 18 mm Wood Spacer

Warming Drawer

Lower trim kit

(optional, supplied separately)

Compact oven

IMPORTANT!

In a wall mounted installation,

there needs to be an 18 mm

Spacer fixed underneath the

warming drawer first to raise

it to the required height.

Warming Drawer

5C CABINETRY DIMENSIONS - WALL MOUNTED (IE INSTALLED WITH A F&P COFFEE MAKER)

600mm

45mm

*PO

PLAN

SIDE

CABINETRY DIMENSIONS mm

MMinimum inside height of cavity

with optional Lower trim kit fitted

without optional Lower trim kit fitted

590

570

NInside width of cavity 560

OMinimum inside depth of cavity 565

Note: When installed in combination with a companion product the companion product may be placed directly onto the

warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able

to support the weight of both products is required.

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.

Additional 18mm Wood Spacer IMPORTANT!

In a wall mounted installation,

there needs to be an 18mm

Spacer fixed underneath the

warming drawer first to raise

it to the required height.

Warming Drawer

Coffee Maker

Warming Drawer

Lower trim kit

(optional, supplied separately)

Coffee Maker

Side rail IMPORTANT!

When installing under an F&P Coffee Maker

you must ensure the supplied anti-tip

bracket is installed, unless there is a fixed

shelf above the drawer acting as an anti-tip

obstacle.

Anti-tip Bracket

Supplied Anti-tip Bracket

(screwed to the back wall)

IMPORTANT!

If installing under the F&P Coffee Maker, ensure there

is the 45mm gap at the back of the cabinet and the

200mm2toekick cutout required for airflow.

Refer to the Coffee Maker Install instructions.

5D CABINETRY DIMENSIONS - WALL MOUNTED (STANDALONE)

120mm

*PO

PLAN

SIDE

CABINETRY DIMENSIONS mm

MInside height of cavity 120

NInside width of cavity 560

OMinimum inside depth of cavity 545

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.

Additional 18mm Wood Spacer IMPORTANT!

In a wall mounted

installation, there needs

to be an 18mm Spacer

fixed underneath the

warming drawer first to

raise it to the required

height.

Warming Drawer

Supplied Anti-tip Bracket

(screwed to the back wall)

Fixed shelf

IMPORTANT!

In a standalone wall mounted installation, you

must ensure that the supplied anti-tip bracket

is installed unless there is a fixed shelf above

acting as an anti-tip obstacle.

Steam Oven

Cabinet below

Cabinet above

Warming Drawer

6DISCARD PACKAGING RESPONSIBLY

7MARK AND PRE-DRILL THE HOLES FOR SECURING THE WARMING DRAWER

8CONNECT THE WARMING DRAWER TO THE MAINS SUPPLY

Recycle responsibly

Unpack the warming drawer and inspect for any signs of damage.

Do not install the warming drawer if it has been damaged.

IMPORTANT!

Packing materials (e.g. plastic bags, polystyrene foam, staples,

packing straps etc) and tools should not be left around during

and after installation, especially if they are within easy reach of

children, as they may cause serious injuries.

IMPORTANT!

 All electrical work may only be carried out by suitably qualified and competent persons in accordance with national and

local safety regulations.

 This warming drawer must be earthed.

Before placing the warming drawer into the cavity, route the power cord into the back of the cavity and plug it in to the

switched socket. The switched socket should be in an easily accessible area within 900mm of the centre rear of the product.

Power requirements

Model Code Power Voltage Wattage

WB60SD 1.6 - 1.8 A 220-240 V 360-420W

IMPORTANT!

Do not lift the warming drawer by the drawer handle.

Andere Handbücher für WB60S Series

Inhaltsverzeichnis

Andere Fisher & Paykel Wärmeschublade Handbücher

Fisher & Paykel

Fisher & Paykel WB30SDEB1 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB60SDEB1 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB60SMG1-SET Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel CHAUFFE-PLATS 9 Series Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB60SDEB1 Betriebsanleitung

Fisher & Paykel

Fisher & Paykel PROFESSIONAL WB76SPEX1 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WDU/WDV series Montageanleitung

Fisher & Paykel

Fisher & Paykel WD60S Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB24SDB1-SET Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel 9 Series Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB60SDEX1 Betriebsanleitung

Fisher & Paykel

Fisher & Paykel DCS WDV2-30 Montageanleitung

Fisher & Paykel

Fisher & Paykel WB60S Series Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB60SDTB1-SET Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel 9 Series Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB60SDEX1 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB24SMB1-SET Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel 9 Series Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB60SDEB1 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB24SDEB2 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel OR90SCG6B1 Leitfaden

Fisher & Paykel

Fisher & Paykel WDVI-30 N Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel 9 Series Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel WB24SDEB1 Bedienungsanleitung

Beliebte Wärmeschublade Handbücher anderer Marken

Siemens

Siemens HW 290 Series Bedienungsanleitung

APW Wyott

APW Wyott WD-2CMF Bedienungsanleitung

Viking

Viking DEWD102SS Bedienungsanleitung

Miele

Miele ESW 6229 Bedienungsanleitung

Brandt

Brandt WD1014X Bedienungsanleitung

KitchenAid

KitchenAid KOWT107ESS Bedienungsanleitung

Gaggenau

Gaggenau WSP 222 Bedienungsanleitung

DCS

DCS WDI Bedienungsanleitung

Electrolux

Electrolux EED21600X Bedienungsanleitung

Fisher

Fisher PROFESSIONAL WB76SPEX1 Bedienungsanleitung

Hanseatic

Hanseatic TCN14J6D-S Bedienungsanleitung

Electrolux

Electrolux EW30WD55GS Bedienungsanleitung

Jenn-Air

Jenn-Air JWD6030CDX Bedienungsanleitung

Gaggenau

Gaggenau WS482710 Bedienungsanleitung

Bosch

Bosch HWD2720UC Bedienungsanleitung

NEFF

NEFF N29HA11Y2 Bedienungs- und Wartungsanleitung

Bull

Bull W85747 Bedienungsanleitung

Viking

Viking EVEWD530 Bedienungsanleitung