Fisher-Price B2108 Bedienungsanleitung

-p

Model Number: B2108, B3469, G5175

PLEASE KEEP FOR FUTURE REFERENCE.

Please read these instructions before assembly and use of this product, as they contain important information.

Adult assembly is required.

Tool needed for assembly: Phillips Screwdriver (not included).

Requires four “D” (LR20) alkaline batteries for operation.

Maximum Weight Limit: 24 lbs. (10.9 kg).

IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs

less than 24 lbs., but is really active and appears to be able to climb

out of the swing, immediately discontinue its use.

Product features and decorations may vary from picture above.

Accessories sold separately.

Smart Response™Swing

Consumer InformationWarnings and Caution

Occasionally a consumer may experience a problem with

one of our products. If this should happen, please call us

toll-free, rather than return this product to the store. Usually,

we can solve the problem over the telephone or send you

replacement parts. Please call Fisher-Price® Consumer

Relations, toll-free at 1-800-432-5437,8AM - 6 PM EST

Monday through Friday. Hearing-impaired consumers using

TTY/TDD equipment, please call 1-800-382-7470.

Or, write to:

Fisher-Price®

Consumer Relations

636 Girard Avenue

East Aurora, New York 14052

•To prevent serious injury or death

from falls and being strangled in

the restraint system:

- Always use the restraint sys-

tem. Never rely on the tray to

restrain child.

- Never use with an active child

who may be able to climb out of

the seat.

•Never leave child unattended.

WARNING

This product contains small parts

in its unassembled state.

Adult assembly is required.

CAUTION

Parts

Front Base Rear Base

Seat with Restraint

2 Seat Tubes

Seat Wire

2 Seat Wire

Caps

2 Accessory Bins

Pad

Toy Bar

(Toys may be different)

Tray

2 Front Legs

(Longer)

2 Rear Legs

(Shorter)

Bracket

(with M4 Lock Nuts)

Housing

Motor Housing

M4 Screw - 4

Shown Actual Size

Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.

#8 x 13/8" Screw - 6

Shown Actual Size

#6 x 5/8" Screw - 8

Shown Actual Size

•Place the front base on a flat surface.

•Position a front leg (longer) so that the tapered end is

downward, as shown.

•While pressing the button on one of the front legs, insert it

into the front base. Push down on the front leg until the

button “snaps” into the hole in the front base.

•Repeat this procedure to assemble the other front leg to

the front base.

Front Base

Tapered End

Front Legs

(Longer)

IMPORTANT!

Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use

if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.

Assembly

•While standing on the front base, pull the front legs up.

The front legs should remain secured to the front base.

If you can remove the front legs, you have not assembled

them correctly to the front base. Reread and repeat

assembly step 1.

Press

Button

Press

Button

Front Legs Pull Up

Pull Up

Front Base

•Position the housing so that the hub is inward.

•While pressing the button on the top of front leg, insert it

into the housing slot, as shown. Push the front leg until the

button “snaps” into the hole in the housing.

•Repeat this procedure to assemble the motor housing to

the other front leg.

•Pull the front legs down to be sure they are secure in the

housings. If you can remove them, you have not assembled

them correctly. Please re-read and repeat this assembly step.

Hub

Housing

Slot Motor

Housing

Front

Legs

Press

Buttons

•Position a rear leg so that the tapered end is upright.

•While pressing the button on the top of the rear leg, insert it

into the housing short tube, as shown. Push the rear leg

until the button “snaps” into the hole in the short tube.

•Repeat this procedure to assemble the other rear leg to the

motor housing short tube.

•Pull the rear legs down to be sure they are secure in the

housings. If you can remove them, you have not assembled

them correctly. Please re-read and repeat this assembly step.

Button

Rear Legs

Motor Housing

Short Tube

Tapered

End

Assembly

•Place the rear base on a flat surface so that the buttons

face the front base.

•While pressing the buttons on each side of the rear base,

fit the rear legs onto the rear base. Push the rear legs

down until the buttons on the rear base “snap” into the

holes in each rear leg.

Rear Base

Front

Base

Rear

Legs

•Position the seat face down, with the top of the seat

facing you.

•Position a seat tube so that the long end is upright and

toward you and the curved end is toward the outside edge

of the seat.

•Insert the curved end of the seat tube through the holes in

the ridges on the seat back.

•Repeat this procedure to assemble the other seat tube to

the seat.

Press

Button

Press

Button

•While standing on the rear base, pull the rear legs up.

They should remain secured to the rear base. If you can

remove the rear legs, you have not assembled them cor-

rectly to the rear base. Reread and repeat assembly step 6.

•Set the frame assembly aside for Assembly step 17.

Rear Legs

Pull Up

Rear Base

Top of Seat

Seat Tube

Long Ends

Ridges

•Pull both rear legs out until they “snap” into place.

Pull

Rear

Leg Pull

Rear

Leg

Curved

End

Assembly

•Insert four M4 screws into the seat tubes and tighten.

•Rotate the seat tubes down.

Seat

Tubes

Bracket

Seat Tubes

•Position the bracket so that the tall end is toward the

bottom edge of the seat.

Hint: The M4 lock nuts have been assembled to the bracket at

the factory. During shipment of this product, they may have

fallen out. Check to be sure there is a lock nut in each hexagonal

opening on the bracket. If one (or more) has fallen out, fit the lock

nut into a hexagonal opening in the bracket. Make sure the

rounded side of the lock nut is facing up.

•Fit the grooves on the bracket to the seat tubes, as shown.

Seat

Tubes

Bracket

Grooves

Tall

End

Bottom

Edge of

Seat

M4 Screw - 4

Shown Actual Size

Lock Nut

Hexagonal

Opening

Shown Actual Size

M4 Lock Nut

Rounded Side

•Fit the seat wire through the slot in the bracket as shown.

Bracket

Slot

Seat Wire

Assembly

•While holding the seat wire in place, carefully turn the

seat around so that the front faces you.

•Position the seat wire cap so that the rounded edge

is upright.

•Fit each end of the seat wire through the hole in each

seat wire cap.

Ends of

Seat Wire

•Turn the seat face down.

•Fit an accessory bin into the groove on each side of the

seat, as shown.

•Insert two #8 x 13/8" screws into each accessory bin

and tighten.

Seat Wire Cap

Seat Wire

Cap

Grooves

Seat

Accessory Bin

•Lift the seat tubes slightly.

•With the seat wire hanging down, insert the ends of the seat

wire through the slots in the seat, as shown.

Slots

Seat Wire

#8 x 1

3/8

”Screw - 4

Shown Actual Size

Seat Wire

Cap Hole

Rounded Edge Up

•Press the seat wire caps

into place.

•Insert two #6 x

5/8"

screws

through each seat wire cap

and tighten.

Seat Wire

Caps

Seat Wire is

Through Hole in

Seat Wire Cap

Press in Place

#6 x 5/8" Screw - 4

Shown Actual Size

Hint: The seat wire caps are designed to fit into the seat only one

way. If the screw holes in the seat wire caps do not align with the

holes in the seat, try switching the seat wire caps onto the

opposite ends of the seat wire.

Assembly

•Fit the pocket on the back of the pad onto the seat back.

•Fit the waist belts through the smaller slots in the pad.

Crotch Belt

Waist Belts

Pad

•Lift the bottom of the pad.

•Insert the pad elastic loops through the holes in the

seat bottom.

•Insert the crotch belt through the slot in the pad.

•From under the seat, fit the elastic loops onto the tabs on

the seat bottom.

•Insert a #8 x 13/8" screw into each frame hub and tighten.

•Again, push down on the seat to be sure the seat is secured

to both frame hubs.

Frame

Hubs

Pad

Elastic

Loops

Holes

Crotch

Belt

Seat Bottom

#8 x 1

3/8

”Screw - 2

Shown Actual Size

•Position the seat assembly so that the front of the seat is

toward the curved front base.

•While pressing the buttons on the swing tubes, insert them

into the frame hubs. Push the swing tubes up until the but-

tons “snap” into the hole in the frame hubs.

•Push down on the seat to be sure the seat is secured in both

frame hubs.

Swing

Tube

Front

of Seat

Curved

Front

Base

Push

Button

Frame Hub

Assembly Battery Installation

Installation

•Locate the battery compartment door on the swing frame.

•Insert a coin into the battery compartment door and pry the

battery compartment door off of the swing frame.

•Insert four “D” (LR20) alkaline batteries.

•Replace the battery compartment door.

Battery

Compartment

Door

Hint: When swinging, sound or power L.E.D. slows/dims/stops,

it’s time to replace the batteries! We recommend using alkaline

batteries for longer battery life.

Battery Safety Information

Batteries may leak fluids that can cause a chemical burn

injury or ruin your product. To avoid battery leakage:

•Do not mix old and new batteries or batteries of different

types: alkaline, standard (carbon-zinc) or rechargeable

(nickel-cadmium).

•Insert batteries as indicated inside the battery compartment.

•Remove batteries during long periods of non-use. Always

remove exhausted batteries from the product. Dispose of

batteries safely. Do not dispose of batteries in a fire.

The batteries may explode or leak.

•Never short-circuit the battery terminals.

•Use only batteries of the same or equivalent type,

as recommended.

•Do not charge non-rechargeable batteries.

•Remove rechargeable batteries from the product

before charging.

•If removable, rechargeable batteries are used, they are

only to be charged under adult supervision.

1.5V x 4

“D” (LR20)

SHOWN ACTUAL SIZE

•Fit the toy bar plugs into the sockets on the swing tubes.

Hint: If the toy bar plugs do not fit into the sockets, turn the

toy bar around.Now, fit the plugs into the sockets.

•Insert two #6 x 5/8" screws into each plug and tighten.

Plug

Toy Bar

(Toys may

be different) Plug

Socket

Plug

Hub

#6 x

5/8

”Screw - 4

Shown Actual Size

•Fit the bottom edge of the pad around the bottom edge

of the seat.

•Hook the elastic loops on each side of the pad to the peg on

the back of the accessory bins.

Elastic

Loop

Elastic

Loop

IMPORTANT! Before each use, inspect this product for

damaged hardware, loose joints, missing parts or sharp

edges. DO NOT use if any parts are missing or broken. Contact

Fisher-Price® for replacement parts and instructions if

needed. Never substitute parts.

Securing Your Child

•Place your child in the seat. Position the crotch belt between

your child’s legs.

•Fasten both waist belts to each side of the crotch belt. Make

sure you hear a “click” on both sides.

•Check to be sure the restraint system is securely attached by

pulling it away from your child. The restraint system should

remain attached.

Crotch

Belt

Waist

Belt

Waist

Belt

•To prevent serious injury or death

from falls and being strangled in the

restraint system:

- Always use the restraint sys-

tem. Never rely on the tray to

restrain child.

- Never use with an active child

who may be able to climb out of

the seat.

•Never leave child unattended.

WARNING

Tighten

Loosen

To tighten the restraint:

•Feed the anchored end of the waist belt up through the

buckle to form a loop . Pull the free end of the waist

belt .

To loosen the restraint:

•Feed the free end of the waist belt up through the buckle to

form a loop . Enlarge the loop by pulling on the end of

the loop toward the buckle. Pull the anchored end of the

waist belt to shorten the free end of the waist belt .

Note: After adjusting the restraint to fit your child, make sure

you pull on it to be sure it is securely fastened.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fisher-Price Babyschaukel Handbücher

Fisher-Price

Fisher-Price M5598 Bedienungsanleitung

Fisher-Price

Fisher-Price G3048 Bedienungsanleitung

Fisher-Price

Fisher-Price L1958 Bedienungsanleitung

Fisher-Price

Fisher-Price R6069 Bedienungsanleitung

Fisher-Price

Fisher-Price FLG89 Bedienungsanleitung

Fisher-Price

Fisher-Price FHW45 Bedienungsanleitung

Fisher-Price

Fisher-Price T5253 Betriebsanleitung

Fisher-Price

Fisher-Price BMB21 Bedienungsanleitung

Fisher-Price

Fisher-Price 75973 Bedienungsanleitung

Fisher-Price

Fisher-Price Y9422 Bedienungsanleitung

Fisher-Price

Fisher-Price V1179 Bedienungsanleitung

Fisher-Price

Fisher-Price B0639 Bedienungsanleitung

Fisher-Price

Fisher-Price BMM27 Bedienungsanleitung

Fisher-Price

Fisher-Price DELUXE TAKE-ALONG 79618 Bedienungsanleitung

Fisher-Price

Fisher-Price T2075 Bedienungsanleitung

Fisher-Price

Fisher-Price G8661 Bedienungsanleitung

Fisher-Price

Fisher-Price T2684 Bedienungsanleitung

Fisher-Price

Fisher-Price B8046 Bedienungsanleitung

Fisher-Price

Fisher-Price P1397 Bedienungsanleitung

Fisher-Price

Fisher-Price 79381 Bedienungsanleitung

Fisher-Price

Fisher-Price W9510 Bedienungsanleitung

Fisher-Price

Fisher-Price M6156 Bedienungsanleitung

Fisher-Price

Fisher-Price CMR40 Bedienungsanleitung

Fisher-Price

Fisher-Price G8653 Bedienungsanleitung

Beliebte Babyschaukel Handbücher anderer Marken

Hudora

Hudora Comfort Montageanleitung

stilum

stilum seta Technische Daten

stilum

stilum volucris 2 Technische Daten

stilum

stilum patis2 Bedienungsanleitung

Graco

Graco OASIS Bedienungsanleitung

highwood

highwood Lehigh Porch Swing Bedienungsanleitung

VERTBAUDET

VERTBAUDET 70334 0022 Bedienungsanleitung

Blumfeldt

Blumfeldt Hollywood Bedienungsanleitung

Graco

Graco Swing N' Bounce Bedienungsanleitung

Oliver & Kids

Oliver & Kids 697793 Bedienungsanleitung

Kids II

Kids II Bright Starts Safari Smiles 60403-ES Bedienungsanleitung

Sunjoy

Sunjoy L-GZ330PCO-1 Bedienungsanleitung

stilum

stilum simius2 Technische Daten

Summer

Summer CUDDLE ME Bedienungsanleitung

IKEA

IKEA EKORRE Bedienungsanleitung

Playcore

Playcore Swing-N-Slide TB 1539 Bedienungsanleitung

Gilis

Gilis Bebe Stars Flora Bedienungsanleitung

Trigano

Trigano TO605 Bedienungsanleitung