Fisher M-Scope CZ-5 Quicksilver Bedienungsanleitung

CZ-5 QuickSilver

Operating Manual

Deep Search, Target I.D. Metal Detector with dual

Fourier Domain Signal Analysis

FISHER RESEARCH LABORATORY

CONTENTS

About Your Detector .............................................................. pg. 1

Condensed Operating Instructions ...................................... pg. 4

Factory Preset “Turn-On-And-Go” Marks ........................ pg. 4

Setting Up................................................................................. pg. 5

Hipmounting ............................................................................ pg. 7

Control Panel .......................................................................... pg. 7

Turn-On Procedure ................................................................. pg. 9

Ground Balancing.................................................................. pg. 9

Pushbutton Method ............................................................. pg. 10

“Bobbing” The Search Coil Method ................................ pg. 11

Search Modes......................................................................... pg. 12

Auto Tune ............................................................................. pg. 12

Target ID ............................................................................... pg. 13

Searching ................................................................................ pg. 17

Pinpointing............................................................................... pg. 20

Pushbutton Pinpoint Mode ..................................................... pg. 20

Target ID and Autotune Modes ............................................. pg. 21

Target Identification ............................................................... pg. 21

Depth Reading........................................................................ pg. 24

Target Recovery ..................................................................... pg. 25

Recovery Tools ....................................................................... pg. 26

False Signals ............................................................................ pg. 26

Battery Replacement ............................................................. pg. 31

Maintenance .......................................................................... pg. 32

Treasure Hunters’ Code Of Ethics.......................................... pg. 33

Where To Use Your Metal Detector In The U.S..................... pg. 34

Specifications ......................................................................... pg. 35

ABOUT YOUR DETECTOR

Your CZ-5 QuickSilver is an extremely advanced and sophisticated

instrument. Here are some important built-in features:

1. VISUAL TARGET IDENTIFICATION. An easy-to-read meter

displays seven, small-target categories. Silver and gold bands

across the top indicate the most likely categories for small

gold and silver targets. When the dual frequency CZ-5

classification circuitry makes identification, the needle

locks

over the center of the appropriate category. If ID is difficult

due to irregular size, conductivity or depth, the CZ-5 will

alert you by jumping back and forth between the most likely

categories. What it will

never

do is lock-on between

categories or gives you a series of numbers to interpret. No

programming, no razzle-dazzle, no nonsense.

2. AUDIO TARGET IDENTIFICATION. A low tone means a ferrous

or iron target: a medium tone indicates a pull-tab or foil,

and a high tone means you’ve probably found a coin. The

tone ID

always

agrees with the meter ID. If the audio

response tone is low, the meter will always read “iron” and

if the tone is high, the meter will always read in one of the

coin categories.

3. PUSHBUTTON DEPTH READING, VCO PINPOINTING. Just push

a button and the volume, pitch and meter needle will rise

as you approach your target and then peak right over it.

The meter gives you a depth reading in inches for coin-sized

objects.

4. WET SAND OPERATION. Salt water is no problem for the CZ-

5. Just flip a switch, reset your ground control and search.

The CZ-5 compensates for salt and sand simultaneously.

5. TARGET SEPARATION. It’s a sad but true fact that most gold

rings, pull tabs, foil and nickels fall into the same conductivity

range. In the past a detector user had to dig a lot of trash

to find any rings or nickels, but not any more. The CZ-5 not

only separates the nickels from the trash, but the tabs from

the tabs. It has a separate ID and discrimination categories

for round pull tabs, rectangular pull tabs, foil and nickels.

Rather than a complicated “notch” system, the individual

categories are sequentially arranged to insure maximum

good target recovery. In a moderately trashy area for

example, you can set the CZ-5 to reject iron and round pull

tabs and still dig nickels and other coins and all gold rings

falling into the nickel, foil and rectangular tab and nickel

categories.

ABOUT YOUR DETECTOR

6. BIG TARGET ALERT. Large shallow items, like a jar lid or a

beer can, overload metal detector circuits making accurate

target ID or trash rejection impossible, but not with the

CZ-5. Whenever it passes over a large shallow target, a

distictive bell-tone immediately warns you that the target is

too large to identify.

7. DEPTH. Target identification in air is easly for just about any

ID metal detector. But the CZ-5 does it in the ground and

does it deeper. Thanks to the patented Fourier Domain Signal

Analysis System, the CZ-5 can identify deeper targets in

mineralized soil.

Two

VLF ground compensation signals are

transmitted (one at 5KHz, one at 15 KHz), giving the circuitry

two ground compensated target response signals to

analyze, compare and identify.

8. SILENT SEARCH, SLOW MOTION DISCRIMINATION. No

threshold, no clicking, no popping, no static. Once you set

the CZ-5 discrimination control to one of its six factory

calibrated, lock-on discrimination points, the audio and visual

target identification circuits will completely ignore everything

identified as belonging in a category below that discrimination

point. For example, a setting of “4” tunes out iron, pull tabs

and foil. As long as you’re at this discrimination point you’ll

never hear the low “iron” tone or the medium tone of pull-

tabs and foil. And since the discrimination categories are

exactly the same as the meter categories, the meter will never

ID iron, pull tabs or foil as long as you remain at “4”. Any false

signal you do hear or see will be in the “coins” category only

because the CZ-5 couldn’t positively identify the target as

iron, foil or a pull-tab.

9. AUDIO BOOST VOLUME CONTROL. The lower range of this

volume control is like any other you’ve ever used. As you

increase it above mid-range, loud, shallow target responses

remain at a fixed volume while faint, deep target sounds

continue to get louder.

10. PUSHBUTTON MANUAL GROUND ADJUST. It’s no secret that a

metal detector will perform its very best when manually

tuned for actual on-site ground conditions. The only problem

is that manual adjustments have always been confusing,

complicated and time consuming, but not with the CZ-5.

Just push the PINPOINT button and lower the coil to the

ground. Then set the GROUND control just below a threshold

tone and you’re ready to search.

11. EASY TO USE. Just pick it up, set the controls on the red marks

and start searching in a “coins only” mode. It couldn’t be

simpler. Or for a maximum performance you can easily

adjust the controls to your own particular situation.

12. SPIDER COIL. The eight-inch, open-center, Spider coil makes

pinpointing even easier. It’s lightweight, tough, Electro-Static

Insulated (E.S.I. Shielded) and 100% waterproof.

13. TWO SEARCH MODES. The VLF, slow-motion discrimination

mode is made for target identification and trash rejection.

The super hot, wide-scan, autotune mode is ideal for deep

search, all-metal treasure hunting and prospecting.

14. DROP-IN BATTERIES. No wires, no clips, no battery packs.

Just drop in two 9V transistor batteries.

15. COMPACT. The CZ-5 breaks down and fits into an optional

carrying case small enough to carry on most airlines.

16. HIP MOUNTABLE. Just slide the control housing off the shaft

and onto your belt. What’s left is so light it will feel like a

part of your arm.

17. DOUBLE LOCKING NON-METALIC LOWER POLE. No shake no

wobbles. No “lock-ring” to lose and no metal parts near

the search coil.

18. LIGHTWEIGHT, BALANCED AND COMFORTABLE. Only three

and 1/2 pounds light with a cushioned arm rest, foam grip,

“S” handle and built-in detector stand.

Read this instruction manual thoroughly, practice often and you’re in

for some exciting treasure hunting. Drop us a line if you have any questions,

comments or good finds to tell us about. In the meantime...

Happy Hunting!

Fisher Research Laboratory

ABOUT YOUR DETECTOR

FACTORY PRE-SET “TURN-ON-AND-GO” MARKS

Your CZ-5 QuickSilver is fairly simple to operate, especially when

compared to other target ID machines. Even so, we strongly

recommend that you read this entire manual. You’ll be able to tune

your CZ-5 to your specific needs and conditions. If you have a good

understanding of how to do it and why, you’ll find more.

If you can’t wait any longer, and you’re an experienced detector

user, here’s some quick instructions to get you going:

1. Set all the controls to the red “Turn-On-And-Go” marks:

GROUND = 5

DISC = 4

SENSITIVITY = 2

MODE = NORMAL

VOLUME = 5

This puts you in a “coins-only” mode and you’re ready

to start searching. Keep in mind that the GROUND

setting of 5 is probably not the optimum setting for

the ground you’re searching and that’s why the

sensitivity level is set low—to reduce false signals

caused by ground mineralization.

2. If you’re using headphones, adjust the volume controls

for a comfortable volume when the coil is passed over

a large shallow object.

3. Walk slowly, overlap your sweeps and keep the search

coil moving. Remember you are in a “motion” search

mode and the coil must be moving at least slightly to

detect a target.

4. When you get a good, repeatable signal, pinpoint

the target by placing the coil on the ground away

from the target, pushing and holding the pinpoint

button and then bringing the coil back over the target.

5. Once you’ve pinpointed the target, note the

approximate depth reading on the meter, then

identify it by releasing the pinpoint button and moving

the coil side to side in short strokes over the target. The

meter needle will lock onto the appropriate target

classification.

6. Good Hunting.

CONDENSED OPERATING INSTRUCTIONS

SETTING UP

The CZ-5 comes to you just about ready to use. The only adjustment

required is the angle of the stem. You may also wish to adjust the

width of the armrest. Take a look at the diagram above and familiarize

yourself with the parts of the CZ-5 before proceeding.

1. Unpack your new CZ-5 carefully. Save the carton and

inserts for future storage or shipment.

2. Take a look inside the locknut on the upper stem. Note

the yellow locking pad on the left hand side and

loosen the lock nut by rotating it fully

counterclockwise.

3. Slip the lower stem into the upper stem. Make sure the

flat side of the stem is aligned with the locking pad

inside the locknut.

4. Adjust the stem length (using the locknut) and the coil

angle (using the nylon wing nut) so the search coil

rests flat on the ground about 6 inches in front of, and

slightly to the right of your right foot, (to the left of your

left foot for left handers). Your arm should be straight

and relaxed, with the grip held loosely.

Drop-in battery compartments

and cable connector at rear

of housing(not shown)

Removable control

housing (belt loop on

underside of housing)

Padded arm rest

Built-in detector stand

Upper stem

Foam hand grip

Upper

lock nut

Center

section

Seven foot

search coil

cable

Lower

lock nut

8-inch Spider

search coil

Adjustable

non-metallic

lower stem

Nylon wing nut

(replacable

Duro-Neoprene

bushings, not

shown)

Figure 1. Fisher M-Scope

CZ-5 Quicksilver

REMEMBER: THE LONGER THE SHAFT, THE MORE YOU

WILL HAVE TO BEND YOUR ELBOW AND THE SOONER

YOUR ARM WILL GET TIRED. THE CZ-5 IS BALANCED FOR

COMFORTABLE SEARCHING IN A TIGHT SEMICIRCLE

AROUND THE FRONT OF THE OPERATOR.

5. With the stem length properly adjusted, wrap the loop

cable tightly around the upper stem and secure it

with the two Velcro straps. Connect the cable

connector to the control housing.

CAUTION: MAKE SURE THAT THE CABLE IS NOT PULLED

TIGHT AT THE CONTROL HOUSING AND THAT YOU HAVE

ENOUGH SLACK AT THE SEARCH COIL TO ADJUST IT TO

ANY ANGLE.

6. With the shaft length and coil angle properly

adjusted, you should be able to move into your

“search” position (as shown in illustration below) by

leaning forward very slightly and raising your arm (still

straight) until the search coil is about 2 inches above

the ground and 12 inches in front of your foot. The

search coil should be parallel to the ground and may

have to be slightly readjusted at this point.

7. If the armrest is too wide or narrow, you may bend it

slightly inward or outward to meet your exact

requirements.

Figure 2. Search Position.

Adjust the stem length and coil angle so

the coil rests flat on the ground about 6

to 12 inches in front of your foot. Move

into your “seach” position by leaning

forward slightly and raising the coil about

2 inches off the ground.

This should put the search coil out about

12 to 18 inches in front of your foot.

SETTING UP

1. GROUND: Used to electronically cancel the effects of

ground mineralization. Proper use of this control will

minimize false ground signals and insure that the CZ-5

is operating at its maximum potential in just about

any ground condition including wet ocean sand.

2. DISC: In the 0 through 6 position the CZ-5 is in the target

ID mode, which is a silent, no-threshold, motion-

discrimination mode of operation with the ability to

identify and then ignore (“reject”) or accept many

kinds of small metal targets. In the AUTOTUNE position,

the CZ-5 is in an all-metal mode. In this mode, the CZ-

5 has a wider and deeper search pattern, however,

it lacks the ability to discriminate or identify and

therefore reject targets.

HIPMOUNTING

1. Disconnect the cable from the control housing and

unwind all but the last twelve inches from the stem.

Secure the lower end of the cable with a Velcro strap

at least twelve inches up from the coil.

2. Slide the control housing off the handle by holding

the handgrip with one hand and pulling the housing

towards you with the other hand.

3. Reconnect the cable to the control housing.

It is

especially important that the cable connector be

installed tightly to prevent false signals during

hipmount use. Tight, but never tightened with anything

but your hands.

4. Put your belt through the slots on the underside of the

housing.

5. Left handers should wear the housing on their right

hip and right handers on their left hip.

NOTE: If you’re working in shallow water you may want

to hang the control housing around your neck or chest-

mount with Fisher’s Chest Harness. Just make sure you

put it in a heavy plastic bag sealed tightly around the

cable. Remember, the only thing waterproof about

the CZ-5 is the search coil.

CONTROL PANEL

3. PINPOINT/DEPTH READING: A three purpose, spring

loaded push-button. When pushed and held, the

CZ-5 goes into a no-motion, all-metal mode for precise

pinpointing and approximate depth reading of coin-

sized targets. This button is also used in conjunction

with the GROUND control during the ground balancing

procedure.

4. SENSITIVITY/BATT TEST: In the extreme counter-clockwise

position, the battery condition is checked as indicated

by a strong or weak tone and a meter reading. When

rotated clockwise, sensitivity to targets (as well as ground

mineralization and electrical interference) is increased.

When in the AUTOTUNE mode, this control also acts as

a “threshold tone” control.

5. HEADPHONES: This connector accepts most stereo

headphones.

6. MODE: NORMAL position for dry land or shallow fresh

water hunting. SALT position for wet-sand ocean

beaches or hunting in shallow surf.

7. VOLUME/OFF: Power on-off and volume control.

Volume is gradually increased from 1 to 5 settings. From

5 to 10, loud target response is held constant while

faint targets continue to get louder.

CONTROL PANEL

Figure 3, Control Panel

345

Andere Handbücher für M-Scope CZ-5 Quicksilver

Inhaltsverzeichnis

Andere Fisher Metalldetektor Handbücher

Fisher

Fisher M-SCOPE 1270 Bedienungsanleitung

Fisher

Fisher M-SCOPE 1225-X Bedienungsanleitung

Fisher

Fisher F22 Bedienungsanleitung

Fisher

Fisher M-Scope CZ-20 QuickSilver Bedienungsanleitung

Fisher

Fisher 1280-X Aquanaut Bedienungsanleitung

Fisher

Fisher CZ-CZ-70 PRO Quicksilver Bedienungsanleitung

Fisher

Fisher F44 Bedienungsanleitung

Fisher

Fisher M-SCOPE 1236-X2 Bedienungsanleitung

Fisher

Fisher M-Scope Gold Bug 2 Bedienungsanleitung

Fisher

Fisher M-SCOPE CZ-3D Bedienungsanleitung

Fisher

Fisher M-Scope COIN STRIKE Bedienungsanleitung

Fisher

Fisher M-Scope CZ-5 Quicksilver Bedienungsanleitung

Fisher

Fisher F19 Bedienungsanleitung

Fisher

Fisher M-SCOPE 1225-X Bedienungsanleitung

Fisher

Fisher M-SCOPE 1236-X2 Bedienungsanleitung

Fisher

Fisher CZ-7a PRO Quicksilver Bedienungsanleitung

Fisher

Fisher 1266-X Bedienungsanleitung

Fisher

Fisher M-Scope ID Excel Bedienungsanleitung

Fisher

Fisher ID EXCEL Bedienungsanleitung

Fisher

Fisher F19 Bedienungsanleitung

Fisher

Fisher M-Scope CZ-20 QuickSilver Bedienungsanleitung

Fisher

Fisher ID EDGE Bedienungsanleitung

Fisher

Fisher Pro-tech Bedienungsanleitung

Fisher

Fisher F2 Bedienungsanleitung

Beliebte Metalldetektor Handbücher anderer Marken

Garrett

Garrett MAGNASCANNER CS 5000 Bedienungsanleitung

Valex

Valex 1800200 Bedienungsanleitung

Gauss

Gauss MIL MD Bedienungsanleitung

Velleman

Velleman CS130 Bedienungsanleitung

Sears

Sears 321.596370 Bedienungsanleitung

Eriez

Eriez X8 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-22 Bedienungsanleitung

Zircon

Zircon MetalliScanner m60c Bedienungsanleitung

nalanda

nalanda MD027 Bedienungsanleitung

REV Ritter

REV Ritter CB-7005 Bedienungsanleitung

Minelab

Minelab F1A4 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs F70 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-12 Bedienungsanleitung

GOLDEN MASK

GOLDEN MASK 5 Bedienungsanleitung

Grizzly

Grizzly YM 203 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 560 Bedienungsanleitung

Accurate Locators

Accurate Locators XL16 IMAGER Bedienungsanleitung