Flare Fireplaces SYMAX Bedienungsanleitung
1 2
ON
AM
PM
OFF
SETTING FAHRENHEIT or CELSIUS
ON
AM
PM
OFF
To change between °C and °F, press
and buttons simultaneously.
NOTE: Choosing °F results in a 12 hour
clock. Choosing °C results in a
24 hour clock.
SETTING the TIME
ON
AM
PM
OFF
1. Press and buttons simultane-
ously. Day
2. Press or button to select a num-
ber to correspond with the day of the
week (e. g.
-
day,
3. Press and buttons simultane-
ously. Hour
4. To select hour press or button.
5. Press and buttons simultane-
ously. Minutes
6. To select minutes press or but-
ton.
and buttons
simultaneously or wait.
CHILD PROOF
ON
AM
PM
OFF
To activate press and buttons
simultaneously. displayed and the
handset is rendered inoperable, except
for the off function.
To deactivate press and buttons
simultaneously. disappears.
MANUAL MODE (HANDSET)
NOTICE
BEFORE OPERATING
1. Make sure MANUAL knob on the GV60 valve is in the ON,
full counterclockwise position.
2. Place the ON /OFF switch (if equipped) in the I(ON) position.
TO TURN ON FIRE
Program Mode
Temperature
Time
Countdown Timer
Battery Status
Signal IndicatorChild Proof
Thermostatic Mode
Fahrenheit or Celsius
SYMAX REMOTE CONTROL INSTRUCTIONS
1| P a ge
ON
AM
PM
OFF
Handset One-Button Operation
(Default Setting)
button until two short beeps
button.
-
ual Mode after main burner ignition.
NOTICE
Change from one-button to two-button ignition operation by
pressing and holding button for 10 sec. immediately after
installing batteries. is displayed and
change is complete will change to .
ON
AM
PM
OFF
Handset Two-Button Operation
Press and button simultaneously
until two short beeps and a blinking
-
-
ual Mode after main burner ignition.
Change from two-button to one-button ignition operation by
pressing and holding button for 10 sec. immediately after
installing batteries. is displayed and
change is complete will change to .
NOTICE
If the pilot does not stay lit after several tries, turn the main valve
knob to OFF and follow the instructions “TURN OFF GAS TO
APPLIANCE” (page 15).
FLAME HEIGHT ADJUSTMENT
ON
AM
PM
OFF
Handset
hold button.
-
button.
DESIGNATED LOW FIRE and HIGH FIRE
NOTE:
operation.
AM
but-
ton. is displayed.
NOTE: -
STANDBY MODE (PILOT FLAME)
Handset
Press and hold
button
TO TURN OFF FIRE
ON
AM
PM
OFF
Handset
button to turn OFF
.
NOTE: There is a 5 sec delay before
the next ignition is possible.
2| P a ge
PROGRAM MODE
1 2
ON
AM
PM
OFF
Press button. , or
, or
displayed.
MODES of OPERATION
ON
AM
PM
OFF
Thermostatic Mode
The room temperature is measured and
compared to the set temperature. The
-
justed to achieve the set temperature.
1 2
ON
AM
PM
OFF
Program Mode
PROGRAMS 1 and 2, each can be pro-
times at a set temperature.
THERMOSTATIC MODE
ON
AM
PM
OFF
Press button. displayed, preset tem-
temperature displayed.
1. Press button.
2. Press or button to enter Manual
Mode.
3. Press button to enter Program Mode.
ON
AM
PM
OFF
1. Press button and hold until dis-
2. To adjust set temperature press or
button.
button or wait.
COUNTDOWN TIMER
ON
AM
PM
OFF
1. Press and hold button until dis-
played, and hour
2.
or button.
button. Minutes
To select hour press
4. To select minutes press
or button.
button or wait.
Press button,
and countdown time
disappear.
NOTE:
Countdown Timer only works in Manual, Thermostatic,
and Eco Modes. Maximum countdown time is 9 hours
and 50 minutes.
AM
but-
ton. is displayed.
If the appliance will not operate, follow the instructions “TURN
OFF GAS TO APPLIANCE”
(page 15)
.
3| P a ge
selected
1
ON
AM
PM
OFF
7. , , displayed, is displayed
shortly, and hour
8. To select hour press or button.
button. , ,
displayed, displayed shortly,
and minutes
10. To select minutes press or but-
ton.
button.
OFF TIME SETTING (PROGRAM 1)
1
ON
AM
PM
OFF
12. , ,
displayed, is displayed
shortly, and hour
13. To select hour, press or button.
button. , ,
displayed, displayed short-
ly, and minutes
15. To select minutes press or but-
ton.
button.
NOTE: Either continue to PROGRAM 2 and set on and off times
or stop programming at this point, and PROGRAM 2 re-
mains deactivated.
NOTE: PROGRAM 1 and 2 use the same on (Thermostatic) and
off temperatures for , and Daily Timer ( , ,
). Once a new on (Thermostatic) and / or off tempera-
ture has been set, that temperature becomes the new
default setting.
NOTE: If , or Daily Timer are programmed for PRO-
GRAM 1 and PROGRAM 2 on and off times, these be-
come the new default times. The batteries must be re-
moved to clear the PROGRAM 1 and PROGRAM 2 on
and off times and temperatures.
or Daily Timer ( , , ) selected
se-
lected” (above).
Set on time and off time for both Saturday and Sunday.
day of the week, for multiple days of the week, or for every day
of the week.
Default settings:
ON
AM
PM
OFF
TEMPERATURE
1. Press button and hold until
and set temperature (set-
ting in Thermostatic Mode) displayed.
2. To continue press button or wait.
-
es.
3. Select off temperature by pressing
the or button.
button.
NOTE: The on (Thermostatic) and off set temperatures are the
same for each day.
ON
AM
PM
OFF
DAY
5. or button to
choose between ,, , ,
.
button.
ON
AM
PM
OFF
1. Press or or button to enter
Manual Mode.
2. Press button to enter Thermostatic
Mode.
NOTE: The set temperature for Thermostatic Mode is the tem-
perature for the on time in Program Mode. Changing the
Thermostatic Mode set temperature also changes the
on time temperature in Program Mode.
4| P a ge
NOTE: The location of the remote control handset is important to assure proper temperature regulation. To obtain a
constant temperature. Flare recommends that the handset should be between 3 and 15 feet away from the appliance
but not directly above it. We also advise that the handset should be located away from any other heat source and not
in direct sunlight as this may affect the temperature sensor located in the remote handset.
Andere Flare Fireplaces Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
