Flash EVENT Series Bedienungsanleitung
LED PAR 7x40W
ZOOM IP65
User Manual
Instrukcja Obsługi
Art No F7100334
SERIES: EVENT
CONTENTS
EN
PL
INTRODUCTION 3
SAFETY INFORMATION 3
PRODUCT INFORMATION 4
INSTALLATION 4
CONNECTION 5
DMX CHART 8
WARNING! Use clamp to rig the xture.
WARNING! When clamping the xture to a truss or other structure at
any other angle than with the yoke hanging vercally downwards, use two
clamps of half-coupler type. Do not use any type of clamp that does not
completely encircle the structure when fastened.
WARNING! Posion or shade the bar so that the front lens will not be
exposed to sunlight or any other strong light source from any angle - even
for a few seconds. See Figure 1. The LED PAR lens can focused the sun’s
rays, creang a potenal re hazard and causing damage.
IMPORTANT! Do not point strong light output from other xtures at the
LED PAR, as intense illuminaon can damaged the display.
Figure 1.
2
Pages: 2-9
Strony: 10-16
INTRODUCTION
SAFETY INFORMATION
THANK YOU FOR PURCHASING LED PAR. FOR SAFETY REASONS
AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY
READ THE INSTRUCTIONS.
Please keep this User Manual
for future consultaon. If you sell
the xture to another user, be sure
that they also receive this instruc-
on booklet.
Unpack and check carefully the-
re is no transportaon damage be-
fore using the xture.
Before operang, ensure that
the voltage and frequency of po-
wer supply match the power
requirements of the xture.
It’s important to ground the
yellow/green conductor to earth
in order to avoid electric shock.
Disconnect main power before
servicing and maintenance.
Use safety chain when xes this
xture. Don’t handle the xture by
taking its head only, but always by
taking its base.
Maximum ambient temperature
is: 40°C Don’t operate it where the
temperature is higher than this.
In the event of serious ope-
rating problem, stop using the
fixture immediately. Never try
to repair the fixture by your-
self.
Repairs carried out by unskil-
led people can lead to damage
or malfunction. Please contact
the nearest authorized techni-
cal assistance center. Always
use the same type spare parts.
Do not connect the device
to any dimmer pack.
Do not touch any wire during
operation and there might be a
hazard of electric shock.
To prevent or reduce the risk
of electrical shock or fire, do
not expose the fixture to rain
or moisture.
The housing must be repla-
ced if they are visibly damaged.
Do not look directly at the li-
ght spot while the fixture is on.
3
PRODUCT INFORMATION
INSTALATION
Light Source:
7x40W RGBW LED’s
Power consumpon: 300W
Power supply voltage:
100-240V, 50/60Hz AC
Macros (Color, Color + Zoom)
Zoom 3.5°-55°
Operang modes: DMX512,
Manual, Auto, Sound-controlled,
Master/Slave, Sound acve,
DMX channel mode
6/12
IP Rang: IP65
Housing made: Aluminium
Cooling: Acve
AC IN/OUT: Tru1Con
3-Pin XLR DMX Input/Output
Net Weight: 8 kg
Gross weight: 8,2 kg
Net Dimensions:
H(40 with handle)
xW(27)xD(20) cm
Pack Size:
H(50)xW(23)xD(23) cm
The unit should be mounted via
its screw holes on the bracket.
Always ensure that the unit is
firmly fixed to avoid vibration
and slipping while operating.
Always ensure that the structu-
re to which you are attaching
the unit is secure and is able
to support a weight of 10 ti-
mes of the unit’s weight. Also
always use a safety cable that
can hold 12 times of the we-
ight of the unit when installing
the fixture. The equipment must
be fixed by professionals. And it
must be fixed at a place where is
out of the touch of people and
has no one pass by or under it.
The fixture may be installed in
any orientation, but if installed
horizontally with a downward
4
beam-angle, water can poten-
tially pool in the fan wells. Under
normal operation the moisture
will evaporate. However, in loca-
tions with high rainfall, you may
wish to fabricate a rain shield
above the fixture, or modify the
position and orientation of the
fixture to minimize pooling.
Two quarter-turn brackets are
supplied with the fixtre if it is
to be flown above the ground.
Rig the fixture to a support truss
or structure using the supplied
brackets and suitable clamps.
Fasten a safety cable between
the support structure and the
attachment point on the fixture.
The safety cable must be able to
bear at least 10 times the weight
of the fixture.
CONNECTION
The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in/out): Tru1CON socket
The connecon is performed using cable with
XLR-female -> XLR-Male plugs.
1
3
22
SHIELD
SIGNAL (+)
SIGNAL (-)
3
1
FEMALE
XLR
MALE
XLR
1
SHIELD
SIGNAL (+)
SIGNAL (-)
FEMALE
XLR
MALE
XLR
2
3
4
5
1
2
3
45
CAUTION! At the last xture, the
DMX signal has to be terminated
with a terminator. Solder a 120Ω
resistor between signal (-) and si-
gnal (+) into a XLR plug and plug
it in the DMX output of the last
xture.
3-PIN XLR
5-PIN XLR
5
The package includes:
❶ - LED PAR (1 pc)
❷ - Power cable type
Tru1CON (1 pc)
❸ - User Manual (1 pc)
❹ - Omega bracket (1 pc)
❶
❷
❸
❹
User
Manual
Using lamp, the change rate of power voltage should be within ±10%,
if the voltage is too high, it will shorten the light’s life.
Input Voltage Frequency Total Power
100-240[V] AC 50/60[Hz] 300[W]
Voltage Specicaon.
6
Control Menu
DMX
Controller DMX 512 DMX 512 120
Ω
Diagram of connecon of devices by DMX cable.
IMPORTANT! The maximum number of devices connected
in series via power cable is 5 pcs.
The connecon is performed using power cable with powerCON con-
nector (included). The device must be operated by qualied personnel.
CAUTION! In the case of cable damage do not aempt to repair. Repla-
cement or repair can be made only on the manufacturer or by a person
with appropriate permissions
MENU
UP DOWN ENTER
DISPLAY
7
CH
No 6 CH 12 CH
1Red Dimmer
2 Green Dimmer Fine (16 bit)
3Blue Strobo
4 White Macro Auto Programm
001-005 Empty
006-040 Prog 1
041-080 Prog 2
081-120 Prog 3
121-160 Prog 4
161-200 Prog 5
201-240 Prog 6
241-255 Empty
5Zoom Macro Programs Speed
6Zoom Fine (16 bit) Red
7 Green
8Blue
9 White
10 CTO
11 Zoom
12 Zoom Fine (16 bit)
DMX CHART
8
9
10
SPIS TREŚCI
WPROWADZENIE 11
INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA 11
INFORMACJE O PRODUKCIE 12
INSTALACJA 12
POŁĄCZENIE 13
TABLICA DMX 16
OSTRZEŻENIE! Do zamocowania urządzenia należy użyć zacisku.
OSTRZEŻENIE! Podczas mocowania urządzenia do kratownicy lub innej
konstrukcji pod innym kątem niż z jarzmem zwisającym pionowo w dół, na-
leży użyć dwóch zacisków typu półzłącza. Nie używaj żadnego typu zacisku,
który nie otacza całkowicie konstrukcji po zamocowaniu.
OSTRZEŻENIE! Przednia soczewka nie powinna być narażo-
na na działanie światła słonecznego lub innego silnego źródła świa-
tła pod jakimkolwiek kątem - nawet przez kilka sekund. Patrz
Rysunek 1. Soczewka LED PAR może skupiać promienie słoneczne, stwa-
rzając potencjalne zagrożenie pożarem i powodując uszkodzenia.
WAŻNE! Nie należy kierować silnego światła z innych urządzeń na LED
PAR, ponieważ intensywne oświetlenie może uszkodzić wyświetlacz.
Rysunek1.
Andere Handbücher für EVENT Series
1
Inhaltsverzeichnis
Sprachen:
Andere Flash Beleuchtungsausrüstung Handbücher
Flash
Flash 5R LASER GUN Bedienungsanleitung
Flash
Flash LED PAR 18x10W RGBW 4in1 IP20 Bedienungsanleitung
Flash
Flash F7100443 Bedienungsanleitung
Flash
Flash F7100070 Bedienungsanleitung
Flash
Flash F7100330 Bedienungsanleitung
Flash
Flash F7100521 Bedienungsanleitung
Flash
Flash 2x Moving Head 7R Bedienungsanleitung
Flash
Flash FL-233 BEAM Bedienungsanleitung
Flash
Flash LED PAR 64 18x12 RGBWA+UV FLAT Bedienungsanleitung
Flash
Flash LED PAR 56 SLIM RGB Aura F7000253a Bedienungsanleitung
Flash
Flash LED WASHER RGB IP34 ver.II Bedienungsanleitung
Flash
Flash F7100320 Bedienungsanleitung
Flash
Flash F7100323 Bedienungsanleitung
Flash
Flash F7200203 Bedienungsanleitung
Flash
Flash HYBRID 10R Bedienungsanleitung
Flash
Flash FOLLOW SPOT 350W Bedienungsanleitung
Flash
Flash WashFX 1000 IP65 Bedienungsanleitung
Flash
Flash F7100525 Bedienungsanleitung
Flash
Flash F7100566 Bedienungsanleitung
Flash
Flash F7000686 Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
