FLASHFORGE 3D PRINTER Adventurer 4 Series Bedienungsanleitung

用户使用手册

Adventurer 4 Series / 冒险家4 系列

User Guide

EN/CN-A01

中文P28

本手册仅适用于闪铸科技冒险家4 系列 3D打印机

This guide is only applicable to FLASHFORGE Adventurer 4 Series 3D printer

Content

Notice

Reference

Chapter 1 Adventurer 4 Series

1.1 - Component Introduction

1.2 - Packing Specification

Chapter 2 Introduction of User Interface

2.1 - Build

2.2 - Prepare

2.2.1 - Preheat

2.2.2 - Filament

2.3 - Settings

2.4 - Maintain

2.4.1 - Upgrade

2.4.2 - Log

2.4.3 - Calibration

2.4.4 - ChangeExtruder

2.4.5 - Maintain

Chapter 3 Software Installation

Chapter 4 Preparation of Device

Chapter 5 Print

Chapter 6 Q&A

Chapter 7 Support and Service

Notice

Safety Notice: please read and strictly follow all the

safety warnings and notice below.

Work Environment Safety

Keep your work place tidy.

Do not operate device in the presence of flammable liquids, gases or dust,

which will cause fire in the high temperature generated by the equipment.

Keep device out of children and untrained people’s reach.

Electrical Safety

Always use the device with a properly grounded outlet. Do not refit device plug.

Ungrounded / improperly grounded / refitted device plugs will increase the risk of

leakage of electricity.

Do not use device in damp environment or under the burning sun. Damp

environment will increase the risk of leakage / exposure to the sun will accelerate

the aging of plastic parts.

To avoid device damage, please use the power supply provided by Flashforge.

Avoid using the device during a thunderstorm.

In case of uncertain accident, please unplug the device if you do not use it for long.

When grounding, plug the power cord into the three-in-one socket and connect to

the external grounding wire through the grounding terminal of the three-in-one

socket.

Check and replace the fuse: To prevent electric shock, please be sure to turn off the

power switch and unplug the power cord before checking or replacing the fuse.

Replace the fuse: Open the fuse box of the three-in-one socket and replace the

fuse with the fuse of 5*20, T10AL250V specification.

Note： Every printer has been tested before leaving factory. It is normal and will not

be of trouble if there are filament residue remaining in the extruder or slight

scratches on the plate.

Environment Requirements

Place Requirements

The device must be placed in a dry and ventilated environment. The distance of

the left, right and back side space should be at least 20cm, and the distance of the

front side space should be at least 35cm. Device storage temperature: RT 0-40℃.

Temperature: RT 15-30℃; moisture: 20%-70%.

Cautions

Keep the inside of the device clean and tidy. Do not place metal objects into the

chute at the bottom of the platform.

Please clean up the remaining in time. It is recommended to operate outside the

equipment.

Any modifications to the device will invalidate the guarantee.

Lower the build plate before loading/unloading filament. The distance between

the nozzle and build plate should be kept for at least 50mm.

Operate the device in well-ventilated environment.

Never use the device for illegal activities.

Never use the device to make any food storage vessels.

Never put the prints into your mouth.

Personal Safety

Do not touch the nozzle and build plate during printing.

Do not touch the nozzle and plate after printing to avoid high temperature scald

or mechanical damage!

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts.

Do not operate the device while you are tired or under the influence of drugs,

alcohol or meditation.

Hot surface

Do not touch

Warning crushing

of hands

Keep this area

clear

Keep body parts away

from moving parts

Legal Notice

All the information in this document is subject to any amendment or change

without the official authorization from Flashforge.

FLASHFORGE CORPORATION MAKES NO WARRANTY OF ANY KIND WITH REGARD

TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

FCC Notice

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: [1] This device may not cause harmful interference,

and [2] this device must accept any interference received, including

interference that may cause undesired operation.

Flashforge shall not be liable for errors contained herein for incidental

consequential damages in connection with furnishing, performance or use of

this material.

This document contains proprietary information protected by copyright.

Filament Requirements

Filament Storage

It’s recommended to use the filaments offered by Flashforge, or from the brands

accepted by Flashforge. Due to the different properties of filaments, you need to

modify printing parameters when using those which are not offered by Flashforge.

All polymers degrade with time. Do not unpack filament until necessary. Filament

should be stored in clean and dry conditions.

Name

Extruder quantity

Printing precision

Position precision

Layer thickness

Build volume

Nozzle diameter

Printing speed

Highest extruder

temperature

Filament type

Power supply

Device size

Printing connection

Filament running

out reminding

Print bed

Remote camera

watching

HEPA 13 Air filter

Adventurer 4

±0.1 mm

(test of 100mm cube)

X/Y axis：0.011 mm；

Z axis：0.0025 mm

0.1~0.4 mm

220 x 200 x 250 mm

0.4(default)

0.6/0.3 mm(optional)

10~150mm/s

265℃/240℃

ABS/PLA/PC/PETG/

PLA-CF/PETG-CF

AC100-240V/DC 24V/

13.3A,320W

500(L)*470(W)*550(H)mm

USB Disk/ Wi-Fi/ Ethernet

√

Flexible spring sheet

√

Adventurer 4 Lite

±0.1 mm

(test of 100mm cube)

X/Y axis：0.011 mm；

Z axis：0.0025 mm

0.1~0.4 mm

220 x 200 x 250 mm

0.4(default)

0.6/0.3 mm(optional)

10~150mm/s

240℃ (265℃ is optional)

ABS/PLA

(according to the nozzle)

AC100-240V/DC 24V/

13.3A,320W

500(L)*470(W)*550(H)mm

USB Disk/ Wi-Fi/ Ethernet

√

Glass plate

Reference

Chapter 1 Adventurer 4 Series

5. Filament intake cover

7. Platform base

9. Touch screen

4. Spool holder

1. Power switch

2. Power socket

8. Build plate

6. Front cover

20. Camera(AD4)

13. Filament guide tube joint

15. Fan for cooling extruder

11. Ethernet input

12. Extruder

10. USB

16. Fan for cooling model

21. Air filter(AD4)

17. Buckle 18. Air duct

3. Filament cover

19. Nozzle

14. Cable slot

1.1 Component Introduction

Adventurer 4 lite features a glass platform

with no camera and no air ﬁlter.

3D Printer Filament After-Sales

Service Card

Screwdriver

0.4-265 Nozzle

（AD4 Equipped）

User Guide Unclogging

Pin Tool

Power Cable

Grease

Allen Wrench

Filament Guide

Tube Joint

Leveling Card

USB Disk

(AD4 Equipped)

1.2 Packing Specification

Scraper

(AD4 Lite Equipped)

用户使用手册

Adventurer 4 Series / 冒险家4 系列

User Guide

EN/CN-A01

中文P28

本手册仅适用于闪铸科技冒险家4 系列 3D打印机

This guide is only applicable to FLASHFORGE Adventurer 4 Series 3D printer

Glue

(AD4 Lite Equipped)

1. Click [Build], and then choose the path to read the print ﬁle.

The interface layout may change whenever there is an upgrade of

firmware. The functions below are only for demonstration purposes.

NOTE: There is no camera on AD4 Lite, This manual uses the interface

screen of the Adventurer 4 as a reference.

2. File list

Tap model file：for file details.

Long press model file：multi-selecting mode on.

Chapter 2 Introduction of User Interface

2.1 Build

Note

The ﬁnished prints will be marked.

Read print file from local

memory card

Read print file from the

USB stick

Details

Extruder temperature

Time used

Speed

Copy the ﬁle to the

local memory card

Amount and type of

ﬁlaments required

Build plate temperature

Pause/Resume printing

Interface

Z：Used when the distance needs to be adjusted between the first printed layer and

the extruder. The up and down arrows indicate that the extruder moves upward or

downward.

Fan：The fan for cooling the model. Wind speed can be adjusted for printing different

filaments.

Click OK to save and apply the changed parameters.

Layer thickness

Check more parameter settings and details

More Settings

You can change ﬁlaments

The switch of LED light

Adjust printing parameters:

extruder temperature/

platform temperature/

printing speed

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere FLASHFORGE 3D PRINTER 3D-Drucker Handbücher

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER CREATOR PRO 2 Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Pro Benutzerhandbuch

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Foto 8.9s Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator 3 Pro Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Pro Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Inventor II S Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Hunter Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER finder Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Focus 8.9 Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Guider2S Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER EN-A01 Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER inventor Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Adventurer 4 Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER finder Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER inventor Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER GUIDER 3 PLUS Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Dreamer NX Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator X Benutzerhandbuch

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Adventurer 3 Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Guider IIS Series Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

LONGER

LONGER LK4 Pro Bedienungsanleitung