Flavel Curve FCRR Series Bedienungsanleitung

Curve

RADIA T FLAME EFFECT GAS FIRE

User Instructions

Model o’s FCRR**R is for use on atural Gas (G20) at a supply

pressure of 20 mbar in G.B. / I.E.

B: “**” refers to fascia variant

I STALLATIO I FORMATIO

CO DITIO S OF I STALLATIO

It is the law that all gas appliances are installed in accordance with the rules in

force only by a competent (e.g. CO GI egistered) Installer in G.B, and in

accordance with the installation instructions and the Gas Safety (Installation and

Use) egulations 1998. Failure to install appliances correctly could lead to

prosecution. It is in your own interest and that of safety to comply with the law.

The fire may be fitted below a combustible shelf provided that the shelf is at least

200mm above the top of the appliance and the depth of the shelf does not exceed

150mm.

The fire may be installed below combustible shelves which exceed 150mm deep

providing that the clearance above the fire is increased by 15mm for each 25mm

of additional overhang in excess of 150mm.

o purpose made additional ventilation is normally required for this

appliance when installed in G.B. When installed I.E. please consult

document I.S. 813 : 1996 Domestic Gas Installation which is issued by the

ational Standards Authority of Ireland. Any purpose made ventilation

should be checked periodically to ensure that it is free from obstruction.

If this appliance is fitted directly on to a wall without the use of a fireplace or

surround, soft wall coverings such as wallpaper, blown vinyl etc. could be affected

by the heat and hot air and may discolour or scorch. This should be considered

when installing or decorating.

The Model number of this appliance is as stated on the rating plate affixed to the

base panel of the fire and the appliance is manufactured by:-

BFM Europe Ltd

Trentham Lakes

Stoke on Trent

ST4 4TJ

ABOUT YOUR EW FLAVEL “CURVE” GAS FIRE

The Flavel “Curve” radiant gas fire incorporates a unique and highly

developed grooved radiant panel. The use of durable ceramic material in the

construction of the radiant panel ensures long and trouble free operation.

When first using the new fire a slight smell may be noticed. This is due to starch

used in the manufacture of the ceramic ribbed fibre back, it is non-toxic and will

soon disappear.

Please take the time to fully read these instructions as you will then be able to

obtain the most effective and safe operation of your fire.

IMPORTA T SAFETY I FORMATIO

WAR I G

This appliance has a naked flame and as with all heating appliances a

fireguard should be used for the protection of children, the elderly and

infirm. Fireguards should conform to B.S. 8423 : 2002 should be fitted.

(Fireguards for use with gas heating appliances).

It is important that this appliance is serviced at least once a year by a CO GI

registered gas installer ( in G.B.) and that during the service the fire is removed

from the fire opening and the flue pipe visually checked for debris or blockages

which must be removed. We recommend that during the annual service,

replacement of the Oxypilot is carried out.

These are conditions of the manufacturers guarantee. After installation or

during servicing a spillage test must always be carried out.

ubbish of any type must NEVE be thrown onto the product, this could affect

safe operation and damage the fire.

Only the correct ribbed fibre back must be used if replacement is required and

only complete and genuine replacement fibrebacks can be sourced from BFM

Europe Ltd.

Always keep furniture and combustible materials well clear of the fire and never

dry clothing or items either on or near to the fire. Never use aerosols or

flammable cleaning products near to the fire when it is in use.

The ceramic ribbed fibre back and glass panel remains hot for a

considerable period after use and sufficient time should be allowed for the

fire to cool before cleaning etc.

SPILLAGE MO ITORI G SYSTEM

This appliance is fitted with a spillage monitoring system which shuts down the fire

if the evacuation of combustion products from the fire is affected by a partially or

fully blocked flue pipe. If this system operates the fire will go out. If this occurs,

leave the fire for at least three minutes then follow the lighting procedure as

described in the previous section. In the event of repeated operation a CORGI

registered gas installer must be called to investigate and rectify the cause.

REMOVAL OF THE CO TROLS COVER

The controls cover is located on the left hand side of the product (when

viewed from the front). The cover is removed by gently lifting away in a

vertical direction as shown below in Fig. 1, to reveal the control valve as

shown in Fig. 2

Fig. 1 Fig. 2

To re-fit the controls cover, locate in the slot and clip and fit back in position.

Lift controls

cover

vertic lly

w y

Control v lve

OPERATI G THE FIRE USI G THE REMOTE CO TROL HA DSET

a) The control valve is positioned on the left hand side of the fire when

viewed from the front. emove the controls cover as shown on

b) To operate the appliance automatically via the remote control handset,

ensure that the on / off switch is switched to the “on” position as shown

below in Fig. 3

Fig. 3

c) Switch the MANUAL control disc to the “ON” position. (Image above

shows “MANUAL” control disc set in the “MAN” position).

d) Switch the main valve knob to the “OFF” position. (Image above shows

“MAIN VALVE” knob set in the “OFF” position.

e) Press and hold the “STA ” button and “UP” button on the remote hand

set simultaneously, see Fig. 4 overpage for image of handset.

f) The valve will then emit an audible beep and commence its ignition

sequence. When the pilot flame has been established, the control will

continue to beep whilst the thermocouple heats up. When the

thermocouple has reached operating temperature, it will allow gas to

flow to the burner and the burner will light at high rate heat input

(6.5kW).

On / Off Switch

“MANUAL”

Control Disk

“MAIN VALVE” Knob

Fig. 4

g) The fire can now be switched between HIGH rate heat input and LOW

rate heat input by pressing the “DOWN” arrow on the handset. To

reduce the flame height of the main burner incrementally, press the

arrow momentarily. To reduce the heat input directly down to the mini

mum level, press the “SMALL” flame arrow on the handset twice,

NOTE : The flame will go to HIGH rate heat input before going to

designated LOW rate heat input. To return back to HIGH rate heat input

press the “LA GE” flame button twice. To put the fire in In “STANDBY

MODE” (only the pilot remains lit) press and hold the “SMALL” flame

arrow on the handset.

AFTER THE PILOT FLAME HAS BEE EXTI GUISHED, IF YOU

WISH TO RE-LIGHT THE APPLIA CE YOU MUST WAIT AT LEAST

THREE MI UTES BEFORE TRYI G TO RE-LIGHT THE FIRE.

“STAR” / “OFF” button

“UP” button

“DOWN” / “STANDBY”

button

“LED” h ndset light

3.3 REMOVAL & RE-FITTI G THE “CURVE” FASCIA

a) The “Curve” fascia is fitted to the product by hooking the top edge of the

fascia over the mounting brackets as shown in Fig. 5 below, then

securing with two screws on the bottom face of the trim as shown in

Fig. 6 below.

Fig. 5

Fig. 6

Align mounting br cket on “Curve”

f sci with mounting br cket on

combustion ch mber nd fix with

screws supplied

Image viewed from

underside of trim

Hook “Curve”

f sci onto top

mounting br ckets

CLEA I G - WAR I G

Before attempting any cleaning operation ensure that the fire has been allowed to

fully cool.

CLEA I G THE STAI LESS STEEL A D PAI TED METAL PARTS

The “Curve” fascia that was supplied with this product must only be cleaned with a

clean, damp cloth.

Abrasive cleaners, chemical cleaning agents or any type of polish must

never be used as damage to the finish may result.

CLEA I G THE RIBBED FIBRE BACK

We do not recommend cleaning of the ribbed ceramic fibre back as this is a fragile

item and damage may result.

one of these parts must be washed or exposed to any cleaning agents or

water.

Any damaged parts must be replaced by contacting your dealer or telephoning

BFM Europe Ltd. on the number stated on the rear cover of this book. The

ribbed ceramic fibre back must only be replaced with a complete and genuine item

and the fire must never be run with a damaged item in position.

The ceramic fibre back used in this product is manuafctured from R.C.F

(Refractory Ceramic Fibre) To ensure that the release of fibres from this item

is kept to a minimum, during installation and servicing we recommend that

you use a HEPA filtered vacuum to remove any dust accumulated in and

around the appliance before and after working on the appliance. When

replacing these articles we recommend that the replaced items are not

broken up, but are sealed within heavy duty polythene bags, clearly labelled

as “RCF waste”. RCF waste is classed as a “stable”, non reactive

hazardous waste and may be disposed of at a landfill licensed to accept

such waste Protective clothing is not required when handling these

articles, but we recommend you follow the normal hygiene rules of not

smoking, eating or drinking in the work area, and always wash your hands

before eating or drinking.

USER REPLACEABLE PARTS

We do not recommend any parts on this appliance are replaced by anyone other

than a CO GI registered engineer.

Due to our policy of continual improvement and development the exact

accuracy of descriptions and illustrations cannot be guaranteed.

Part o. B-106080

Issue 3

BFM Europe Ltd.

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

www.bfm-europe.com

Telephone - General Enquiries : (01782) 339000

Telephone - Service : (0844) 7700169

Inhaltsverzeichnis

Andere Flavel Kamin im Innenbereich Handbücher

Flavel

Flavel Quasar NRDC MN2 Series Montageanleitung

Flavel

Flavel Renoir FRECR0MN Bedienungsanleitung

Flavel

Flavel Atlanta FAVRU0MN Bedienungsanleitung

Flavel

Flavel EmberGlow Classic FEMC00EN Montageanleitung

Flavel

Flavel REGENT L.F.E. RC Montageanleitung

Flavel

Flavel Finesse FSRC**MN Montageanleitung

Flavel

Flavel Renoir FRECN0EN Montageanleitung

Flavel

Flavel Enchant FSCP**MN Bedienungsanleitung

Flavel

Flavel Linear Montageanleitung

Flavel

Flavel Linear HE Montageanleitung

Flavel

Flavel Caress HE Montageanleitung

Flavel

Flavel Calypso Montageanleitung

Flavel

Flavel Emberglow FEBC00MN Bedienungsanleitung

Flavel

Flavel RENOIR RC Montageanleitung

Flavel

Flavel Decadence HE Series Montageanleitung

Flavel

Flavel Linear Pebble FRDPU0MN Bedienungsanleitung

Flavel

Flavel Kenilworth HE Montageanleitung

Flavel

Flavel FSCC12MN Bedienungsanleitung

Flavel

Flavel Misermatic FRCM1G Bedienungsanleitung

Flavel

Flavel FRDC**MN Series Bedienungsanleitung

Flavel

Flavel FSSP00MN Montageanleitung

Flavel

Flavel FWERN0MN Bedienungsanleitung

Flavel

Flavel Curve Bedienungsanleitung

Flavel

Flavel Orchestra Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch