Flextool SP118OFT Leitfaden

OPERATION AND PARTS MANUAL

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Revision #0 (01/04/10)

PN: 38364

SP1 SERIES

CONCRETE/ASPHALT STREET

MODEL SP118OFT

HONDA GX390 PETROL ENGINE

SERIAL NO. ____________

PAGE 2 — SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10)

PROPOSITION 65 WARNING

Engine exhaust and some of

its constituents, and some dust created

of California to cause cancer, birth

defects and other reproductive harm.

by power sanding, sawing, grinding,

drillingandotherconstructionactivities

contains chemicals known to the State

Some examples of these chemicals are:

Leadfromlead-basedpaints.

Crystallinesilicafrombricks.

Cementandothermasonryproducts.

Arsenicandchromiumfromchemically

treatedlumber.

Your risk from these exposures varies,

dependingonhowoftenyoudothistype

of work. To reduce your exposure to

these chemicals: work in aALWAYS

well ventilated area, and work with

approved safety equipment, such as

dust masks that are specially designed

to filter out microscopic particles.

SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10) — PAGE 3

Grinding/cutting/drilling of masonry, concrete, metal and

other materials with silica in their composition may give

off dust or mists containing crystalline silica. Silica is a

basic component of sand, quartz, brick clay, granite and

numerous other minerals and rocks. Repeated and/or

substantial inhalation of airborne crystalline silica can

cause serious or fatal respiratory diseases, including

silicosis. In addition, California and some other

authorities have listed respirable crystalline silica as a

substance known to cause cancer. When cutting such

materials, always follow the respiratory precautions

mentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and

other materials can generate dust, mists and fumes

containing chemicals known to cause serious or fatal

injury or illness, such as respiratory disease, cancer,

birth defects or other reproductive harm. If you are

unfamiliar with the risks associated with the particular

process and/or material being cut or the composition of

the tool being used, review the material safety data

sheet and/or consult your employer, the material

manufacturer/supplier, governmental agencies such as

OSHA and NIOSH and other sources on hazardous

materials. California and some other authorities, for

instance, have published lists of substances known to

cause cancer, reproductive toxicity, or other harmful

effects.

Control dust, mist and fumes at the source where

possible. In this regard use good work practices and

follow the recommendations of the manufacturers or

suppliers, OSHA/NIOSH, and occupational and trade

associations. Water should be used for dust

suppression when wet cutting is feasible. When the

hazards from inhalation of dust, mists and fumes cannot

be eliminated, the operator and any bystanders should

always wear a respirator approved by NIOSH/MSHA for

the materials being used.

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

SILICOSIS/RESPIRATORY WARNINGS

PAGE 4 — SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10)

TABLE OF CONTENTS

SP1 StreetPro

Professional Pavement Saw

Proposition 65 Warning ........................................... 2

Silicosis/Respiratory Warnings ................................ 3

Table Of Contents .................................................... 4

Training Checklist ..................................................... 6

Daily Pre-Operation Checklist ................................. 7

Safety Information .............................................. 8-14

Dimensions/Speciﬁcations (Saw) .......................... 16

Speciﬁcations (Engine) .......................................... 17

General Information ............................................... 18

Components .......................................................... 19

Basic Engine .......................................................... 20

Inspection/Setup ............................................... 21-23

Blades ............................................................... 24-26

Raise/Lower And Depth Stop ................................ 27

Operation .......................................................... 28-31

Maintenance (Saw) ................................................ 32

Maintenance (Engine) ........................................... 33

Decommissioning/Water Tank (Optional) ............... 34

Troubleshooting (Saw) ........................................... 35

Troubleshooting (Engine) ....................................... 36

Explanation Of Code In Remarks Column ............ 38

Suggested Spare Parts ......................................... 39

Component Drawings

Nameplate And Decals ..................................... 40-41

Console Frame Assembly ................................. 42-43

Platform Frame/Undercarriage Assembly ......... 44-45

Raise/Lower Assembly ..................................... 46-47

Lifting Bale Assembly ....................................... 48-49

Pointer Assembly .............................................. 50-51

Blade Spindle Assembly ................................... 52-53

Blade Guard Assembly ..................................... 54-55

Engine Assembly .............................................. 56-57

Belts And Tensioning Assembly ........................ 58-59

Belt Guard Assembly ........................................ 60-61

Water System Assembly ................................... 62-63

Optional Water Tank Assembly ......................... 64-65

Honda GX390U1QWT2 Engine

Air Cleaner Assembly ....................................... 66-67

Camshaft Assembly .......................................... 68-69

Carburetor Assembly ........................................ 70-71

Control Assembly ............................................. 72-73

Crankcase Assembly ........................................ 74-75

Crankshaft Assembly ........................................ 76-77

Cylinder Barrell Assembly ................................ 78-79

Cylinder Head Assembly .................................. 80-81

Fan Cover Assembly ......................................... 82-83

Flywheel Assembly ........................................... 84-85

Fuel Tank Assembly .......................................... 86-87

Ignition Coil Assembly ...................................... 88-89

Mufﬂer Assembly .............................................. 90-91

Piston Assembly ............................................... 92-93

Recoil Starter Assembly ................................... 94-95

Labels Assembly .............................................. 96-97

SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10) — PAGE 5

NOTES

PAGE 6 — SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10)

TRAINING CHECKLIST

Training Checklist

No, Description OK? Date

1Read operation manual

completely.

Machine layout, location of

components, checking of engine

and hydraulic oil levels.

3 Fuel system, refueling procedure.

4 Operation of spray and lights.

5Operation of controls (machine

not running).

6Safety controls, safety stop switch

operation.

7 Emergency stop procedures.

8Startup of machine, pre-heat,

engine choke.

9 Forward and reverse travel.

10 Starting a cut.

11 Pavement cutting techniques.

12 Stopping a cut.

13 Restart after stopping blade within

work surface — explanation

14 Shutdown of machine.

15 Lifting of machine (lift loops).

16 Machine transport and storage.

SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10) — PAGE 7

DAILY PRE-OPERATION CHECKLIST

Daily Pre-Operation Checklist      

1 Hardware and damage check

2 Engine oil level

3 Hydraulic oil level

4 Condition of blade

5 Safety stop switch operation

6 Braking control operation

PAGE 8 — SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10)

SAFETY INFORMATION

Do not operate or service the equipment before reading

the entire manual. Safety precautions should be followed

at all times when operating this equipment.

Failure to read and understand the safety

messages and operating instructions could

result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you

about potential hazards that could injure you or others. The

safety messages speciﬁ cally address the level of exposure

to the operator and are preceded by one of four words:

DANGER, WARNING, CAUTION or NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided,

COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided,

COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this

equipment will be referenced with hazard symbols which

may appear throughout this manual in conjunction with

safety messages.

Lethal exhaust gas hazards

Explosive fuel hazards

Burn hazards

Rotating parts hazards

Symbol Safety Hazard

Cutting and crushing hazards

Hydraulic fluid hazards

SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10) — PAGE 9

SAFETY INFORMATION

GENERAL SAFETY

CAUTION

NEVER operate this equipment without proper protective

clothing, shatterproof glasses, respiratory protection,

hearing protection, steel-toed boots and other protective

devices required by the job or city and state regulations.

Avoid wearing jewelry or loose ﬁ tting clothes that may

snag on the controls or moving parts as this can cause

serious injury.

NEVER operate this equipment when not

feeling well due to fatigue, illness or when

under medication.

NEVER operate this equipment under the

inﬂ uence of drugs or alcohol.

ALWAYS clear the work area of any debris, tools, etc.

that would constitute a hazard while the equipment is

in operation.

No one other than the operator is to be in the working

area when the equipment is in operation.

DO NOT use the equipment for any purpose other than

its intended purposes or applications.

NOTICE



This equipment should only be operated by trained and

qualiﬁ ed personnel 18 years of age and older.



Whenever necessary, replace nameplate, operation and

safety decals when they become difﬁ cult read.

Manufacturer does not assume responsibility for any

accident due to equipment modiﬁ cations. Unauthorized

equipment modiﬁ cation will void all warranties.

NEVER use accessories or attachments that are not

recommended by Multiquip for this equipment. Damage

to the equipment and/or injury to user may result.

ALWAYS know the location of the nearest

ﬁ re extinguisher.

ALWAYS know the location of the nearest

ﬁ rst aid kit.

ALWAYS know the location of the nearest phone or

keep

a phone on the job site.

Also, know the phone numbers

of the nearest ambulance, doctor and

ﬁ re department.

This information will be invaluable in the case of an

emergency.

PAGE 10 — SP1 PAVEMENT SAW • OPERATION AND PARTS MANUAL — REV. #0 (01/04/10)

SAFETY INFORMATION

SAW SAFETY

DANGER

Engine fuel exhaust gases contain poisonous carbon

monoxide. This gas is colorless and odorless, and can

cause death if inhaled.

The engine of this equipment requires an adequate free

ﬂ ow of cooling air. NEVER operate this equipment in any

enclosed or narrow area

where free ﬂ ow of the air is

restricted. If the air ﬂ ow is

restricted it will cause injury

to people and property and

serious damage to the

equipment or engine.



NEVER operate the equipment in an explosive

atmosphere or near combustible materials. An

explosion or ﬁ re could result causing severe

bodily harm or even death.

WARNING



If applicable, NEVER use your hand to ﬁ nd

hydraulic leaks. Use a piece of wood or

cardboard. Hydraulic ﬂ uid injected into the

skin must be treated by a knowledgeable

physician immediately or severe injury or

death can occur.



Accidental starting can cause severe injury

or death. ALWAYS place the ON/OFF

switch in the OFF position.

NEVER disconnect any emergency or safety devices.

These devices are intended for operator safety.

Disconnection of these devices can cause severe injury,

bodily harm or even death. Disconnection of any of these

devices will void all warranties.

CAUTION

Anytime the saw is lifted onto its nose or tilted fully

back, such as for maintenance access, the high end of

the saw MUST be blocked up to prevent the possibility

of crush injury.

DANGEROUS

GAS FUMES

NOTICE

ALWAYS ensure saw is securely

placed on appropriate

blocks or jackstands when performing maintenance

requires elevation of the saw.

If saw has brakes, ensure brakes are applied when

leaving or when using on a slope. Some saws utilize a

brake system where the brakes are automatically applied

when the engine is stopped.

If saw has a parking brake, ensure that the parking

brake is engaged and holds the saw safely in place

when parking on a slope.. Turning the saw across the

angle of the slope will help prevent accidental downhill

movement.

ALWAYS block the saw with appropriate blocks when

leaving the saw parked on a slope.

To prevent unexpected loss of control, DO NOT

start

engine on a sloping surface

DO NOT

use on excessive slopes or on extremely uneven

surfaces

ALWAYS start engine with the control handle in

NEUTRAL position to prevent unexpected movement.

ALWAYS

keep the machine in proper running condition.

Fix damage to machine and replace any broken parts

immediately.



Make sure there is no buildup of concrete, grease, oil or

debris on the machine.

ALWAYS

store equipment properly when it is not being

used. Equipment should be stored in a clean, dry location

out of the reach of children and unauthorized personnel.

Inhaltsverzeichnis

Andere Flextool Gesehen Handbücher

Flextool

Flextool FBS-36E Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung