FLIR Elara FR-345-EST Bedienungsanleitung

Elara FR-345-EST QIG Rev 110

December 2020

This document does not contain any export-controlled information.

Elara™ FR-345-EST

Quick Install Guide

1 Check Contents

Make sure all of the items above are included in the camera kit.

2 Select a Location

Select a suitable location to mount the camera.

The focus for both of the camera's sensors is fixed at one meter (39.4"). If it will be

used in EST screening mode, make sure to install the camera so that the faces of

persons being screened for EST are 1m ± 0.2m (39.4" ± 7.9") away from the front

of the camera.

Verify that the operating temperature is 15°C to 45°C (60°F to 110°F), 0-95%

relative humidity. The camera provides optimal performance in a stable

environment near 22°C (72°F).

For further advice on positioning and orienting the camera, see the camera's

installation and user guide.

3 Configure the Camera

FLIR recommends configuring the camera on a bench or in a lab before mounting

and aiming it. However, it is also possible to configure the camera after mounting

it, which could be more appropriate for certain installations.

3.1 Install the FLIR DNA tool

To discover the camera on the network, FLIR recommends using the FLIR

Discovery Network Assistant (DNA) tool. Version 2.3.0.19 or higher supports Elara

FR-345-EST, does not require a license to use, and is a free download from

Elara FR-345-EST QIG Rev 110

December 2020

This document does not contain any export-controlled information.

FLIR.com > Products > Security > FLIR EST Thermal Screening Solutions > FLIR

Elara™ FR-345-EST > Support > Resources.

3.2 Connect the Camera

System Cable

a. Attach an Ethernet cable to the RJ45

connector for a 10/100 Mbps Ethernet

and PoE+ (Power over Ethernet)

IEEE 802.3at connection.

Make sure the camera and the PC

you are using to configure the

camera are on the same LAN

segment.

b. Connect the alarm connectors, if

needed.

c. If using an external 12 VDC or 24

VAC power supply, connect its wires

to the two-pin power terminal block.

Then, insert the terminal block into

the power connector.

Connector

Black

RJ-45

Black

12-30 VDC (±10%) /

24 VAC (21-28 VAC) -

Red

12-30 VDC (±10%) /

24 VAC (21-28 VAC) +

Yellow

NOT USED

Orange

NOT USED

Purple

NOT USED

Green

NOT USED

Red

ALARM IN signal

Black

ALARM IN GND

Brown

ALARM OUT signal

Blue

ALARM OUT COM

3.3 Configure for Networking

You can configure the camera for networking using the DNA tool, the camera's

web page, or a supported VMS.

DNA tool

Camera's web page

Discover camera IP address

•

Configure IP address, mask, and gateway

•

Configure DNS settings, MTU, and Ethernet speed

•

Change user credentials

•

Configure more than one camera at the same time

•

For information about using the supported VMS to configure the camera, see the

VMS documentation.

By default, DHCP is enabled on the camera and a DHCP server on the network

assigns the camera an IP address. For example, if the camera is managed by

FLIR's Horizon or Meridian VMS and the VMS is configured as a DHCP server, the

VMS automatically assigns the camera an IP address.

Elara FR-345-EST QIG Rev 110

December 2020

This document does not contain any export-controlled information.

If the camera is managed by FLIR’s Latitude VMS or is on a network with static IP

addressing, you can manually specify the camera’s IP address using the DNA tool

or the camera's web page. The camera's default IP address is 192.168.0.250.

To manually specify the camera's IP address using the DNA tool:

a. Run the DNA tool (DNA.exe) by double-clicking .

The Discover List

appears, showing

compatible

devices on the

LAN segment and

their current IP

addresses.

In the DNA Discover List, verify that the camera's status is Online.

If this is the first time you are configuring the camera or if it is the first time after

resetting the camera to its factory defaults, DNA automatically authenticates

the camera with the default password for the camera's admin user (admin).

If the admin user password has been

changed, you need to authenticate the

camera.

In the DNA Discover List, right-click the

camera and select Login.

In the DNA - Login window, type the

password for the admin user. If you do

not know the admin user password,

contact the person who configured the

camera's users and passwords.

Click Login, wait for Ok status to

appear, and then click Close.

In the DNA Discover List, verify that the camera's status is Authenticated.

b. Change the camera’s IP address.

Right-click the camera and select IP Setup.

Elara FR-345-EST QIG Rev 110

December 2020

This document does not contain any export-controlled information.

In the DNA - IP Setup window, clear

Use DHCP and specify the camera's IP

address. You can also specify the Mask

(default: 255.255.255.0) and Gateway.

Then, click Update, wait for Ok

status to appear, and then click Close.

4 Install the Camera

The camera can be mounted directly on a wall or a ceiling, or it can be mounted

using the CB-WLBX-G4 Wall & Surface Mount Kit, which includes a junction box.

For the full list of mounting and other accessories available for the camera, see the

FLIR Security Cameras - Accessory Guide.

4.1 Fit Mounting Hardware

If using the CB-WLBX-G4 Wall & Surface Mount Kit with junction box, install it

according to the installation guide for that accessory.

If using other mounting hardware, install the mounting hardware for the camera

according to instructions.

4.2 Prepare the Surface for Mounting

Be sure to have the required accessories

and tools available.

Refer to the camera's installation and

user guide as necessary.

a. Attach the mounting template sticker

onto the wall or ceiling where you are

mounting the camera.

b. Drill six anchor holes according to the

template.

c. Hammer the six plastic anchors into

the drilled holes.

d. If the system cable is going to exit

from the rear, drill a hole in the center

of the mounting template for the

cable.

The system cable can exit either from

the side of the camera's mounting

bracket or through the hole in the

back of the mounting bracket.

Side cable exit

Elara FR-345-EST QIG Rev 110

December 2020

This document does not contain any export-controlled information.

Rear cable exit

4.3 Route Cables and Connect the Camera

a. If you are using a mounting accessory, install the power and network cabling in

the mounting hardware so that it is accessible when the camera is mounted.

b. Attach an Ethernet cable from the network switch to the RJ45 connector.

c. Connect the alarm connectors, if needed.

d. If using an external 12 VDC or 24 VAC power supply, connect its wires to the

two-pin power terminal block. Then, insert the terminal block into the power

connector.

4.4 Mount and Aim the Camera

a. Place the camera over the surface

and securely fasten the T10 self-

tapping screws clockwise into the

plastic anchors.

Make sure that the camera’s general

orientation covers the required field

of view.

b. Aim the camera.

Support the camera's weight with

your hand. Then, loosen the three

locking screws and adjust the

camera's pan, tilt, and rotation.

Important

While aiming the camera, make sure to support the

camera's weight with your hand.

Tip

FLIR recommends aiming the camera while monitoring the

camera's live video on the camera web page or in a video stream.

Elara FR-345-EST QIG Rev 110

December 2020

This document does not contain any export-controlled information.

c. Make sure that the toothed surfaces

are properly aligned and meet

evenly. Then, use the T10 torx

wrench to securely tighten each

locking screw.

5 Boresight the Camera

The admin user or any user assigned the admin or expert role

can boresight the camera using the camera's web page, which

supports Google Chrome (recommended), Firefox, Microsoft

Edge, and Internet Explorer 11 (32-bit), on PCs running 64-bit

Windows 7, 8, 8.1, or 10.

a. In the DNA Discover List, double-click the camera.

b. On the login screen, type a user name and password. Both

are case-sensitive.

When logging in to the camera's web page for the first time or for the first

time after resetting the camera to its factory defaults, type admin for the user

name and for the password.

Then, specify a new password for the admin user. Use a strong password

consisting of at least eight characters and at least one uppercase letter, one

lowercase letter, and one number. Passwords can include the following

special characters: |@#~!$&<>+_-.,*?= .

Log back in using the new password.

The camera's View Settings Home Page opens.

c. Click System Settings > Boresight. The Boresight page opens.

d. Using the digital pan, tilt, zoom, and crosshair controls, align the

visible video image with the thermal video image.

e. Click Save.

Elara FR-345-EST QIG Rev 110

December 2020

This document does not contain any export-controlled information.

Important

After powering up the camera, wait 30 minutes before

commencing screening. The camera's thermal sensor needs to

stabilize. In System Settings, click Firmware & Info, and make

sure the Temperature is stable.

For information about using the camera's web page to perform additional

configuration steps, see the camera's installation and user guide.

6 Attach the Camera to a Supported VMS

After you have mounted the camera and discovered or defined its IP address, you

can use VMS Discovery/Attach procedures to attach the camera to a supported

VMS.

7 Camera Dimensions

The Elara FR-345-EST camera’s dimensions are:

Side View

Front View

8 Register the Product

For warranty information, see https://www.flir.com/support-

center/warranty/security/flir-security-product-warranties/.

9 Contact Information

FLIR Systems, Inc.

6769 Hollister Avenue

Goleta, CA 93117

USA

Support: https://www.flir.com/support/

Corporate Headquarters

27700 SW Parkway Ave.

Wilsonville, OR 97070

USA

Andere Handbücher für Elara FR-345-EST

Inhaltsverzeichnis

Andere FLIR Digitalkamera Handbücher

FLIR

FLIR ORYX R Bedienungsanleitung

FLIR

FLIR MPX C233BD Bedienungsanleitung

FLIR

FLIR M-Series Bedienungsanleitung

FLIR

FLIR 310 Series Bedienungsanleitung

FLIR

FLIR Ariel CM-3102 Handbuch

FLIR

FLIR CP-4221-300 Bedienungsanleitung

FLIR

FLIR ORION SC7000 Bedienungsanleitung

FLIR

FLIR HS-324 Bedienungsanleitung

FLIR

FLIR BLACKFLY S GIGE Bedienungsanleitung

FLIR

FLIR Exx series Bedienungsanleitung

FLIR

FLIR USB3 Vision GRASSHOPPER 3 Bedienungsanleitung

FLIR

FLIR Elara FR-345-EST Bedienungsanleitung

FLIR

FLIR PTZ-35 MS Bedienungsanleitung

FLIR

FLIR Photon Block 2 Bedienungsanleitung

FLIR

FLIR BLACKFLY S USB Vision Bedienungsanleitung

FLIR

FLIR X-Series Bedienungsanleitung

FLIR

FLIR FIREFLY Bedienungsanleitung

FLIR

FLIR Elara DX Series Bedienungsanleitung

FLIR

FLIR LADYBUG 5 USB3 Bedienungsanleitung

FLIR

FLIR GF300 Bedienungsanleitung

FLIR

FLIR C237BD Bedienungsanleitung

FLIR

FLIR Tau Bedienungsanleitung

FLIR

FLIR AX Series Bedienungsanleitung

FLIR

FLIR FIREFLY Bedienungsanleitung

Beliebte Digitalkamera Handbücher anderer Marken

Mercury

Mercury 350K Bedienungsanleitung

Pentax

Pentax Optio LS 465 Bedienungsanleitung

Sanyo

Sanyo VPC-S1085 Bedienungsanleitung

GE SMART A1255 Bedienungsanleitung

Point Grey

Point Grey Gazelle Bedienungsanleitung

Nikon

Nikon COOLPIX A Bedienungsanleitung

Pentax

Pentax P-5 Bedienungsanleitung

BlazeVideo

BlazeVideo A280 Bedienungsanleitung

Sony

Sony MCA-20 Bedienungsanleitung

Sony

Sony Alpha DSLR-A290 Bedienungsanleitung

ATIK Cameras

ATIK Cameras One Bedienungsanleitung

CohuHD Costar

CohuHD Costar 3930 Series Bedienungsanleitung

Leica

Leica M10-R Bedienungsanleitung

FujiFilm

FujiFilm FinePix A700 Bedienungsanleitung

Lorex

Lorex LNZ81P25 Series Bedienungsanleitung

GE J1470S Bedienungsanleitung

Sony

Sony A6700 Benutzerhandbuch

Canon

Canon EOS ELAN7 Bedienungsanleitung