FLIR M-Series Bedienungsanleitung

FLIR M-Series and NavNet TZtouch

Overview

The following example illustrates the integration of the FLIR M-Series into a NavNet network. The M-

Series and the JCU controller are set with a fix IP address compatible with NavNet TZtouch. When you

purchase a FLIR (with JCU), it will have a different IP address and will require changes before it is

used with the TZtouch system.

Installation

FLIR Configuration

You have to assign the M-Series and the Controller (JCU), a fixed IP address. We recommend you use

192.168.252.200 / 255.255.255.0 for the M-Series Camera, and 192.168.252.201 / 255.255.255.0

for the JCU (although any IP beginning with 192.168.252.x would work as long as they don’t collide

with any existing IP).

The FLIR M-Series and the JCU controller are UPnP-enabled devices. You can easily see the list of

UPnP-enabled devices from your computer by opening “My Network Places” if using a Microsoft XP

computer or “Network” if using a Vista, Windows 7 or Windows 8 computer. Note that the M-Series

and JCU will only appear on your PC, if they are all on the same network domain.

Normally, the JCU gets its power from the camera when directly connected to the M-Series. When

connecting the JCU to a HUB or Switch, you must use a power injector (48V) to power the unit (see

diagram above).

When the computer is connected to the M-Series Camera and JCU via an Ethernet cable or via a

Hub/Switch (without router or DHCP server on the network), the M-Series and JCU automatically

assign themselves an IP address of 169.254.x.x / 255.255.0.0. In order to access the configuration

page of the M-Series and JCU, you need to setup your PC on that network (ex: 169.254.1.2 /

255.255.0.0)

Note: If your computer is set to “obtain an IP address automatically,” it should automatically set an IP

address of 169.254.x.x from the FLIR after two minutes. However, it is easier to directly fix the PC IP

address at 169.254.1.2 / 255.255.0.0.

Note: If the JCU and the M-Series were previously assigned another IP address, you can display the

JCU IP address by pressing the COLOR button while pushing the puck. You can then assign an IP

address to your PC accordingly, and thus be able to access the M-Series and JCU configuration page.

Once the computer is on the same domain as the M-Series and JCU, and UPnP is enabled, you should

see the M-Series and JCU icon under “My Network Places” (XP) or “Network” (Vista/Windows 7/

Windows 8):

Note: If the devices do not appear, try to restart the M-Series and JCU, then check if your computer is

setup to display UPnP notifications:

xUsing Windows XP:

ͲStart the Control Panel and go to Add/Remove programs

ͲOn the left-hand side, select the Add/Remove Windows components

ͲFrom the Windows Component Wizard, scroll down to Networking Services, then highlight

and select the “Details” button

ͲCheck the box to enable the UPnP User Interface and select Ok

ͲSelect Next when returning to the Windows Component Wizard

ͲSelect Finish

xUsing Windows Vista and Windows 7

ͲTurn on “Network Discovery” on the “Network” page as highlighted below:

CAMERA SETUP:

Double click on the M-SERIES icon to open its configuration webpage. To configure a fixed IP address,

click on “Network Setup”:

Select the Static (fixed) option rather than Dynamic:

The screen will refresh, and the IP, Mask, and Gateway fields will change from grey to white,

indicating they can accept user entries. Once you have entered the appropriate IP address and subnet

mask (192.168.252.200 / 255.255.255.0 in this example), click on the “Save” link and wait 1 minute.

Note: You will not be able to access anymore the M-Series configuration page after changing its IP

address (until you change the IP address of your computer later in this process).

JCU SETUP

Go back to “My Network Places” or “Network” and double click on the JCU icon to open its

configuration page.

Set the Network Addressing to “Static”:

Enter the appropriate IP address and subnet mask (192.168.252.201 / 255.255.255.0) and click on

the “Save”.

FINAL SETUP

After changing the IP address of the M-Series Camera and JCU, change the IP address of the PC

(192.168.252.10 / 255.255.255.0) to confirm that you see the FLIR and JCU icon again in “My

Network Place” (XP) or “Network” (Vista/Windows 7,8).

Note: You may need to restart the Camera and JCU for the Icon to appear in “My Network Place”.

TZtouch Configuration

Press the [HOME] key, the [MENU] button and select [Camera]. Press [Scan] under “FLIR

Installation”:

This should automatically enter the IP address of the M-Series. If the M-Series is correctly detected,

you should see a green light:

IMPORTANT: If the M-Series is not discovered automatically, refer to the appendix (at the end of this

document) to configure the internal M-Series NEXUS server.

Once the FLIR has been detected, select the video input where the analog video output of the FLIR is

connected:

Note: You could connect the analog video output of the M-Series to an AXIS IP video converter. In

that case, you would select the corresponding IP Camera feed in the menu above.

Using an AXIS converter allows the video to be distributed on the network and available on every

TZtouch MFD.

APPENDIX

How to enable the discovery and control of the M-Series from the PC

In some instances, the internal server of the M-Series (“NEXUS” server) is configured in a way that

prevents the PC from discovering it and controlling it. If you are unable to discover the M-Series from

your TZtouch display but are able to use the Web Control of the M-Series to control it via a web

browser on your PC, follow the guide below.

Note: If you are not able to control the M-Series from a Web Browser on your PC, make sure that the

Ethernet connection and IP addresses are correctly setup.

Open a Web Browser and type the IP address of the M-Series: http://<IP ADRESS >.

Example: http://192.168.252.200

Note: To access the Web Server configuration, just type the IP address (do not add any port number)

The Nexus configuration page should appear. Log in as an admin (default password is “indigo”)

Click on “Configuration File”:

Scroll at the very bottom of the page and click on “Download Configuration File”

Save the file somewhere on your computer (on the desktop for example).

Open the configuration file (“server.ini”) with NotePad and look for the section “[Networking

Configuration]”

Set “Enable Network Discovery”, “Enabled” and “Allow Anonymous Clients” to “yes”:

Note: You can search the text file for “Anonymous”, “Discovery” and “Enabled” to find the line you

need to check.

Save the file.

Note: Make sure that you don’t modify anything else.

Go back to the Nexus Configuration page (you might have to log in again), select “Configuration File”

and scroll down to the bottom of the page. Click on “Choose file” and select the “server.ini” file you

just modified. Click on “Upload”.

The FLIR M-Series Nexus server needs to be restarted to take the changes into account.

Go to the very top of the page (header) and click on “Stop”

Wait until the Start button appears, and then click on it.

Your TZtouch display should now be able to detect and control the Camera.

Andere Handbücher für M-Series

Inhaltsverzeichnis

Andere FLIR Digitalkamera Handbücher

FLIR

FLIR X-Series Bedienungsanleitung

FLIR

FLIR Lorex LW3211-C Bedienungsanleitung

FLIR

FLIR BLACKFLY USB3 Vision Bedienungsanleitung

FLIR

FLIR FC S Series Montageanleitung

FLIR

FLIR Tau Camera TAU-0035-00-10 Bedienungsanleitung

FLIR

FLIR A6 Series Bedienungsanleitung

FLIR

FLIR BLACKFLY S GIGE Bedienungsanleitung

FLIR

FLIR M-Series Bedienungsanleitung

FLIR

FLIR 310 Series Bedienungsanleitung

FLIR

FLIR FIREFLY Bedienungsanleitung

FLIR

FLIR M500 Bedienungsanleitung

FLIR

FLIR FIREFLY Bedienungsanleitung

FLIR

FLIR ThermaCAM QuickView Bedienungsanleitung

FLIR

FLIR ZENMUSE XT2 Bedienungsanleitung

FLIR

FLIR Alpha Nir Bedienungsanleitung

FLIR

FLIR CP-4221-300 Bedienungsanleitung

FLIR

FLIR GRASSHOPPER 3 Series Gebrauchs- und Pflegehandbuch

FLIR

FLIR USB3 Vision GRASSHOPPER 3 Bedienungsanleitung

FLIR

FLIR MPX C233BD Bedienungsanleitung

FLIR

FLIR Flir MPX Bedienungsanleitung

FLIR

FLIR C2 Bedienungsanleitung

FLIR

FLIR AX Series Bedienungsanleitung

FLIR

FLIR A310 ex Series Bedienungsanleitung

FLIR

FLIR HS-324 Bedienungsanleitung

Beliebte Digitalkamera Handbücher anderer Marken

Mercury

Mercury 350K Bedienungsanleitung

Pentax

Pentax Optio LS 465 Bedienungsanleitung

Sanyo

Sanyo VPC-S1085 Bedienungsanleitung

GE SMART A1255 Bedienungsanleitung

Point Grey

Point Grey Gazelle Bedienungsanleitung

Nikon

Nikon COOLPIX A Bedienungsanleitung

Pentax

Pentax P-5 Bedienungsanleitung

BlazeVideo

BlazeVideo A280 Bedienungsanleitung

Sony

Sony MCA-20 Bedienungsanleitung

Sony

Sony Alpha DSLR-A290 Bedienungsanleitung

ATIK Cameras

ATIK Cameras One Bedienungsanleitung

CohuHD Costar

CohuHD Costar 3930 Series Bedienungsanleitung

Leica

Leica M10-R Bedienungsanleitung

FujiFilm

FujiFilm FinePix A700 Bedienungsanleitung

Lorex

Lorex LNZ81P25 Series Bedienungsanleitung

GE J1470S Bedienungsanleitung

Sony

Sony A6700 Benutzerhandbuch

Canon

Canon EOS ELAN7 Bedienungsanleitung