Flowserve Limitorque QX Bedienungsanleitung

Experience In Motion

USER INSTRUCTIONS

Installation

Operation

Maintenance

Limitorque QX Electronic Actuator

FCD LMENIM3306-06 – 07/14

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

Contents

1 Important Notes 7

2 Quick Start 9

2.1 Calibrate – Position Limits 10

2.1.1 Electrical Operation Feature 10

2.1.2 Handwheel Operation Feature 12

2.1.3 Entering the Setup Mode 15

2.2 DDC Option 15

2.3 Check the Settings 15

3 Installation and Operation 16

3.1 Preparing the Stem Nut 16

3.1.1 Torque Applications 16

3.2 Mechanical Installation onto Valve or Gearbox 18

3.3 Electrical Connections 18

3.3.1 Removing Terminal Cover 18

3.3.2 Terminal Compartment Documents 18

3.3.3 Sealing Cable/Conduit Entries 19

3.3.4 Recommended Terminal Connections 19

3.3.5 Termination of Cables 21

3.3.6 Cable Connections 21

3.3.7 Network Installations 22

3.3.8 Foundation Fieldbus Installation 25

3.3.9 Network Wiring – Proﬁbus DP/PA Installation 26

3.3.10 Network Wiring – DeviceNet 27

3.3.11 Replacing Terminal Cover 27

3.3.12 External Earth/Ground Connections 27

3.4 Terminal Block Shield Installation 27

3.5 Commissioning the Actuator 28

3.5.1 Default Conﬁguration Set 28

3.5.2 View the Existing Settings 30

3.5.3 Entering the Setup Mode 30

3.5.4 Setting Position Limits 31

3.6 Operating the QX Actuator 34

3.6.1 Manual Operation 34

3.6.2 Electrical Operation 34

3.6.3 Local Control 34

3.6.4 Remote Control 35

3.6.5 Local Indication 35

4 Customizing the Actuator 37

4.1 Changing the Existing Settings 37

4.2 Password Entry 39

4.3 New Password 40

4.4 Valve Setup 41

4.4.1 Close Direction 41

4.4.2 Close Seating 41

4.4.3 Open Seating 41

4.5 Torque Switch Timer 42

4.5.1 Status 42

4.5.2 Torque Timer 42

4.6 Operating Time 43

4.7 Torque Setup 43

4.7.1 Close Torque Valve or Open Torque Valve 44

4.8 Position Setup 44

4.8.1 Set Position Limits for Electrical Operation 44

4.8.2 Set Position Limits for Manual Operation 45

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

ﬂowserve.com

4.9 Modutronic Option 47

4.9.1 Status 47

4.9.2 Proportional Band 47

4.9.3 Fail Position 47

4.9.4 Deadband 47

4.9.5 Polarity (20 mA) 47

4.9.6 Delay After Stop 48

4.9.7 4-20 mA Signal Range 48

4.9.8 Set High Reference 48

4.9.9 Set Low Reference 48

4.9.10 Modutronic LCD Display 49

4.10 DDC Option 49

4.10.1 Status 49

4.10.2 Network Address 50

4.10.3 Protocol 50

4.10.4 Analog Scale 50

4.10.5 ESD Action 50

4.10.6 Proportional Band 51

4.10.7 Deadband 51

4.10.8 Offset 51

4.10.9 Move To 51

4.10.10 Comm Loss Delay 51

4.10.11 Comm Loss Action 51

4.11 FF Option 51

4.11.1 Status 52

4.11.2 Terminate Bus 52

4.11.3 Analog Scale 52

4.11.4 ESD Action 52

4.11.5 OPEN/CLOSE Mode 52

4.11.6 Proportional Band 52

4.11.7 Deadband 52

4.11.8 Comm Loss Delay 53

4.11.9 Comm Loss Action 53

4.12 PB Option 53

4.12.1 Status 54

4.12.2 PB DP Operation 54

4.12.3 Comm Loss Delay 55

4.12.4 Comm Loss Action 55

4.13 DN Option 55

4.13.1 Status 56

4.13.2 Baud Rate 56

4.13.3 Network Address 56

4.13.4 ESD Action 56

4.13.5 Proportional Band 56

4.13.6 Deadband 56

4.13.7 Comm Loss Delay 57

4.13.8 Comm Loss Action 57

4.14 Status and Alarm Contacts 57

4.14.1 Status and Alarm Contact Default Settings 58

4.14.2 Status Function 58

4.14.3 Contact 59

4.14.4 Valve Position 59

4.15 Two-speed Timer (Optional) 59

4.15.1 Status 59

4.15.2 Start Position 59

4.15.3 Stop Position 60

4.15.4 Pulse Time – ON 60

4.15.5 Pulse Time – OFF 60

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

4.16 Change Analog Out 60

4.16.1 APT Polarity Option 62

4.16.2 ATT Polarity Option 63

4.17 Remote Mode 63

4.18 Local Control 64

4.18.1 LED Customization 64

4.19 ESD (Emergency Shutdown) Overrides 64

4.19.1 ESD Override 65

4.19.2 Inhibit 65

4.19.3 Local Command 65

4.19.4 Stop 65

4.19.5 Jammed Valve* 65

4.19.6 Lost Phase* 66

4.19.7 Overtorque* 66

4.19.8 Motor Thermostat 66

4.19.9 Oil Over Temperature 66

4.19.10 Two-Speed Timer 66

4.19.11 Network ESD 67

4.19.12 Torque Switch Timer 67

4.20 Inputs 67

4.20.1 Input Standard Remote Control 67

4.20.2 Status 68

4.20.3 Custom Input Mode #1 – Momentary ESD/PSESD (Optional) 68

4.20.4 Custom Input Mode #2 – Momentary ESD/CSE (Optional) 71

4.20.5 Custom Input Mode #3 – ESD Time Delay Relay 71

4.20.6 Custom Input Mode #4 – Multi-Position Mode (Optional) 72

4.21 Monitor Relay 73

4.22 Diagnostic Reset 74

4.23 TAG Number 75

4.24 LCD Contrast 76

4.25 Motor Thermostat 76

4.26 Change Valve Data 76

4.27 Change Port 77

5 Troubleshooting 78

5.1 View Diagnostics Routine 79

5.2 Troubleshooting Problems/Corrective Action 79

5.2.1 Actuator Fails to Operate 79

5.2.2 Jammed Valve Detected 80

5.2.3 Actuator Operates but Does Not Drive Valve 80

5.2.4 Valve Does Not Seat Correctly 80

5.2.5 Status Messages 81

5.3 View Diagnostics 83

5.4 View Hardware Status 84

5.5 View Motor Status 85

5.6 View Power Supply 85

5.7 View Identiﬁcation 85

5.8 View Torque Proﬁle 86

5.9 View Operation Log 86

5.10 View DNET Status? 88

6 Maintenance 90

6.1 Lubrication 90

6.1.1 Oil Capacities 90

6.1.2 Checking Oil Level 90

7 Regulatory Information 91

7.1 Speciﬁc Conditions for Safe Use — Atex/Cenelec/IECEx Applications 94

7.2 Statement of Compliance with Applicable European Directives 94

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

ﬂowserve.com

Figures

Figure 1.1 – QX-05 Actuator 7

Figure 2.1 – Electrical operation 12

Figure 2.2 – Handwheel operation 14

Figure 2.3 – QX travel stops 14

Figure 3.1 – Top view - stem nut with standard keyway position 17

Figure 3.2 – Exploded view of QX bases 17

Figure 3.3 – Power terminal connector size limitations 19

Figure 3.4 – Terminal block 20

Figure 3.5 – Control terminal connector size limitations 20

Figure 3.6 – View of terminal block 22

Figure 3.7 – Standard wiring diagram - three phase shown 23

Figure 3.8 – Removing outer plastic jacket 23

Figure 3.9 – Separating cable parts 24

Figure 3.10 – Stripping conductors and applying heat shrink tubing 24

Figure 3.11 – Ring tongue connectors 24

Figure 3.12 – Terminal block shield 28

Figure 3.13 – User network connection for loop topology 29

Figure 3.14 – External earth/ground connection – housing 29

Figure 3.15 – View settings 31

Figure 3.16 – Position setup – electrical operation 33

Figure 3.17 – Declutch lever shows direction of engagement (QX-05 shown) 34

Figure 3.18 – Control panel 35

Figure 4.1 – Entering the setup mode 38

Figure 4.2 – Main menu selections 38

Figure 4.3 – Changing settings 39

Figure 4.4 – Password entry 40

Figure 4.5 – New password 40

Figure 4.6 – Valve setup 41

Figure 4.7 – Torque switch timer 42

Figure 4.8 – Operating Time Setup 43

Figure 4.9 – Torque setup 43

Figure 4.10 – Typical XP nameplate 44

Figure 4.11 – Electrical operation 46

Figure 4.12 – Handwheel operation 46

Figure 4.13 – Modutronic option 48

Figure 4.14 – Modutronic signals 49

Figure 4.15 – DDC 50

Figure 4.16 – Foundation Fieldbus 53

Figure 4.17 – Proﬁbus DP 54

Figure 4.18 – Proﬁbus PA 55

Figure 4.19 – DN Option 57

Figure 4.20 – Status and alarm contacts (Shown with optional boards added) 59

Figure 4.21 – Two-speed timers 60

Figure 4.22 – Change Analog Out 61

Figure 4.23 – Change Analog Out Voltage – APT 61

Figure 4.24 – Change Analog Out Current – APT 61

Figure 4.25 – Change Analog Out Voltage – ATT 62

Figure 4.26 – Change Analog Out Current – ATT 62

Figure 4.27 – Remote mode 63

Figure 4.28 – Local control 64

Figure 4.29 – ESD Overrides 65

Figure 4.30 – Inputs 68

Figure 4.31 – Custom Input Mode 70

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

Figure 4.32 – Monitor relay 73

Figure 4.33 – Diagnostic reset 75

Figure 4.34 – TAG number 75

Figure 4.35 – LCD contrast 76

Figure 4.36 – Motor thermostat 76

Figure 4.37 – Change valve data 77

Figure 4.38 – Change port and Bluetooth settings 77

Figure 5.1 – Initialize routine 83

Figure 5.2 – Diagnostic overview 84

Figure 5.3 – View hardware status 84

Figure 5.4 – View motor status 85

Figure 5.5 – View power supply 85

Figure 5.6 – View identiﬁcation 86

Figure 5.7 – View torque proﬁle 86

Figure 5.8 – View operation log 87

Figure 5.9 – View DNET status 88

Figure 7.1 – Typical ATEX nameplate 95

Tables

Table 3.1 – Available QX Flanges 13

Table 3.2 – Terminal block rating; power terminals 20

Table 3.3 – Terminal block rating; control terminals 21

Table 3.4 – Required ratings for external wires 22

Table 3.5 – Loop topology connections 25

Table 3.6 – Foundation Fieldbus connections 26

Table 3.7 – Proﬁbus cable speciﬁcations 26

Table 3.8 – DeviceNet cable speciﬁcations 27

Table 3.9 – Default conﬁgurations 29

Table 3.10 – LED Indicators – default settings 36

Table 4.1 – Digital Input Terminals 72

Table 6.1 – Oil capacities 90

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

ﬂowserve.com

Figure 1.1 – QX-05 Actuator

OPTIONAL

1 Important Notes

• Please read this manual in its entirety before attempting to install or operate your QX actuator. A full understanding

of the installation and operation options will assist you in installing the actuator in the most effective manner.

Limitorque has designed the QX actuator for long life even in the harshest environments. Flexible control and protec-

tion options are provided to ensure the actuator meets your requirements.

• All actuator enclosures are sealed by O-rings, and cable entries are supplied with threaded plugs to protect the

terminal compartment until the unit is wired. If the actuator cannot be installed immediately, it is recommended that

it be stored in a clean, dry place, preferably in an area that is not subject to large ﬂuctuations in temperature.

• Disconnect all incoming power before opening any cover on the actuator. The user/operator must ensure that safe

working practices are employed at all times and are in accordance with local or national standards that are enforced

at the particular site.

• To install and commission the actuator, only the terminal compartment cover needs to be removed. See Figure

1.1, Item 10. Settings for commissioning the actuator are done externally; therefore, no other covers need to be

removed. The actuator was assembled in ideal dry conditions and the total sealing of the enclosure protects all

electrical components against deterioration.

Piece Description

1Handwheel

2Declutch Lever (QX-05)

3Oil Fill

4Controls Cover

5LCD

Piece Description

6Control Knob

7Ground Lug

8Baseplate

9Conduit Entry

10 Terminal Compartment

Piece Description

11 Motor

12 Certiﬁcation Nameplate

13 Tag Nameplate

14 Oil Plug

15 Stem Nut Stops

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

NOTE: Removal of any cover, other than the terminal compartment cover, will invalidate the unit warranty. Exposure

of actuator components to an environment that results in deterioration of internal components will also invalidate the

unit’s warranty.

• During ﬁnal ﬁeld installation, ensure that all cable entries are correctly sealed in accordance with National Standards

or Regulatory Authorities. All temporary transit plugs must be removed and any unused cable entries closed in an

approved manner. See Section 3.3.3, Sealing Cable/Conduit Entries.

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

ﬂowserve.com

2 Quick Start

Quick Start provides step-by-step instructions for commissioning each QX actuator. These instructions are for the

following:

• Position limits calibration – can be performed one of two ways:

1. Electrical operation: See Section 2.1.2, Electrical Operation Feature.

2. Handwheel operation: See Section 2.1.2, Handwheel Operation Feature.

• DDC operation: See Section 2.2, DDC Option.

When these Quick Start instructions are complete, the position limits will be set and the actuator will be ready for

normal operation.

NOTE: Units are shipped with default operating time values based on unit size:

QX-1: 5-20 sec, default 15 sec

QX-2: 8-30 sec, default 30 sec

QX-3: 15-60 sec, default 60 sec

QX-4: 30-120 sec, default 60 sec

QX-5: 60-120 sec, default 60 sec

These times are based on a 90° open to close span.

The operating time can be set as desired by following the instructions in document LMENIM3306, QX Actuator

Instruction, Operation and Maintenance Manual.

Limitorque QX Electronic Actuator FCD LMENIM3306-06 – 07/14

2.1Calibrate Position Limits

1. Conﬁrm that the QX actuator is correctly installed on the valve as described in Section 3 Installation and Operation.

2. Refer to the nameplate for the correct main power supply voltage. Switch on the main power to the unit.

3. Turn the red knob to the “STOP” position. The “SET UP ENGLISH?” message will be displayed, select “YES”. The

“SET CLOSE POSITION LIMIT?” message will then be displayed. Proceed with setting the open and close limits of

the valve.

4. Calibrate end position limits one of two ways:

• Electrically, using the control panel. See Section 2.1.1, Electrical Operation Feature.

• Manually, using the handwheel. See Section 2.1.2, Handwheel Operation Feature.

Once the position limits have been set, the LCD message will indicate the valve position as a percentage of the valve

opening.

While setting limit switches, place the red selector knob in the “LOCAL” position to permit the actuator to run open or

closed in push-to-run mode (inching) only.

a CAUTION: Extreme care must be taken as the valve approaches its end position.

The unit will not function with the red selector knob in the “REMOTE” position until both limit switches are set.

The existing conﬁguration of the actuator/valve parameters may be viewed by entering the “SETUP” mode.

2.1.1 Electrical Operation Feature

This feature allows for quick and simple calibration. From a virgin startup, the “SET CLOSE POSITION LIMIT?” message

will be displayed once the setup language has been selected.

NOTE: Refer to Figure 2.1 – Electrical operation as a guide during setup

a CAUTION: Do not adjust close stop while stop is loaded. It is highly recommended that the stops be turned until

they are almost removed from the housing before setting the limits. Once the limits have been set, then the

stops maybe tightened. Refer to Figure 2.3.

Closed Position Limit

1. “SET CLOSE POSITION LIMIT?” is displayed on the LCD.

2. Select “YES.” The “CLOSE VALVE - OK?” message is displayed.

3. Switch the actuator to “LOCAL” control and use the open/close switch to position the valve to the desired closed

position.

4. Back out the close stop if needed. First loosen the screw securing the stop then move stop.

NOTE: Do not adjust close stop while stop is loaded.

5. When the valve is in the desired position, switch the actuator back to “STOP” and select “YES” again. The LCD will

read “SAVE CLOSE LIMIT OK?”

6. Select “YES” if the valve’s close limit position is correct. The close position limit is set.

7. Turn the close stop against the drive sleeve, then back off the close stop from the drive sleeve approximately 0.5 to

1.5 turns, ensuring the stop does not contact the drive sleeve.

Andere Handbücher für Limitorque QX

Inhaltsverzeichnis

Andere Flowserve Controller Handbücher

Flowserve

Flowserve ARGUS E25 MOD II Bedienungsanleitung

Flowserve

Flowserve Limitorque QX Leitfaden

Flowserve

Flowserve Limitorque MX-40 Bedienungsanleitung

Flowserve

Flowserve Limitorque Accutronix MX Bedienungsanleitung

Flowserve

Flowserve SNA250 Handbuch

Flowserve

Flowserve Valtek VL-C Bedienungsanleitung

Flowserve

Flowserve PMV D3 Bedienungsanleitung

Flowserve

Flowserve LTQ008 Series Bedienungsanleitung

Flowserve

Flowserve ROTADISK RD Bedienungsanleitung

Flowserve

Flowserve Centura DBL Series Montageanleitung

Flowserve

Flowserve 2 Series Bedienungsanleitung

Flowserve

Flowserve Limitorque LTQ0 3 Series Bedienungsanleitung

Flowserve

Flowserve Automax Aviator Handbuch

Flowserve

Flowserve FlowAct Series Bedienungsanleitung

Flowserve

Flowserve NAF Series Leitfaden

Flowserve

Flowserve LPC Series Bedienungsanleitung

Flowserve

Flowserve Automax Aviator Montageanleitung

Flowserve

Flowserve Automax SuperNova S050 Montageanleitung

Flowserve

Flowserve Limitorque L120-190 Bedienungsanleitung

Flowserve

Flowserve NORBRO 40R Series Bedienungsanleitung

Flowserve

Flowserve Limitorque L120 Series Bedienungsanleitung

Flowserve

Flowserve LMENIM5001-02 Betriebsanleitung

Flowserve

Flowserve Limitorque L120-85 Bedienungsanleitung

Flowserve

Flowserve Limitorque LTQ008 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung