Flowserve DataFlo P Bedienungsanleitung

DataFlo P

Smart Positioner

Functions

FCD WCAIM2060-00 (Part 08023)

1. Remove cover and apply appropriate voltage to terminals 1 (neutral

or negative) and 2 (hot or positive).

2. Connect input source to terminals 10 (-) and 11 (+) and 12 (if

applicable).

3. The display should be ﬂashing between “Pos” and a number

between 0 and 100.

4. Simultaneously press and hold the “SEL” and “DN” keys for three

seconds. “CAL” will be displayed for two seconds and the security

code will be checked. If the required security code is not zero

(“0000”), the display will begin alternating between “CodE” and

“0000.”

NOTE: If the required code is zero, it will not need to be entered, i.e.,

it will be bypassed and display will automatically ﬂash “SEtL.” Skip

to paragraph 8.

5. Enter the security code, if necessary, as follows. (If the code is

forgotten, the special number 4800 can be used to gain entry.)

6. Quick tap “SEL” key once. First 0 will ﬂash. Quick tap “UP” key until

you reach code number. Quick tap the “DN” key once. The second 0

will ﬂash. Quick tap “UP” key until the next code number is reached.

Continue this procedure as needed for the remaining code numbers.

Quick tap “SEL” to accept code.

7. The display now ﬂashes between “SEtL” and a value.

8. Simultaneously press and release “SEL” and “UP” keys, then adjust

input signal to lower input value, e.g., 4 mA. Quick tap “SEL” to lock

in value.

9. Quick tap “DN” key. Display will ﬂash “SEtU” and a value.

Worcester Actuation Systems

10. Simultaneously press and release “SEL” and “UP” keys, then adjust

input signal to higher input value, e.g., 20 mA. Quick tap “SEL” to

lock in value.

11. Quick tap “DN” key. Display will ﬂash between “PoC” and a number

between 0 and 5 volts.

12. Simultaneously press and release “SEL” and “UP” keys. Using the

“DN” key, adjust so shaft is full clockwise. The display should read

between .200 and .400 volts. If not, rotate potentiometer face gear

with your ﬁngers. It is a friction ﬁt. Quick tap “SEL” to lock in read-

ing.

13. Quick tap “DN” key. Display will ﬂash between “PoCC” and the

feedback voltage value.

14. Simultaneously press and release “SEL” and “UP” keys. Using the

“UP” key, adjust so shaft is full counterclockwise. Quick tap “SEL”

to lock in reading.

15. Quick tap “DN” key. Display will ﬂash between “Cyt” and a cycle

time reading.

16. Simultaneously press and release “SEL” and “UP” keys. Actuator

will automatically close, then open to measure cycle time, displaying

“PoC” at the clockwise position and “PoCC” at the counterclockwise

position.

Calibration is now complete. Press and hold “SEL” key for three seconds.

Positioner reverts to automatic control by input signal.

FCD WCAIM2060-00 Printed in USA.

(Part 08023)

For more information about

Flowserve Corporation,

visit www.ﬂowserve.com or call

USA 1-800-225-6989.

Irving, Texas, USA. Flowserve is

a registered trademark of

Flowserve Corporation.

Worcester Actuation Systems

FLOWSERVE FLOW CONTROL

Worcester Actuation Systems

5114 Woodall Road

P.O. Box 11318

Lynchburg, VA 24506-1318

Phone: 434-528-4400

Fax: 434-845-9736

Inhaltsverzeichnis

Andere Flowserve Ventilstellungsregler Handbücher

Flowserve

Flowserve Logix 3200MD Bedienungsanleitung

Flowserve

Flowserve ARGUS MW 8 Bedienungsanleitung

Flowserve

Flowserve APEX 8000 Series Betriebsanleitung

Flowserve

Flowserve P3 Series Betriebsanleitung

Flowserve

Flowserve APEX 7000 Bedienungsanleitung

Flowserve

Flowserve Logix 3200IQ Leitfaden

Flowserve

Flowserve Logix 520si Series Bedienungsanleitung

Flowserve

Flowserve Logix 3200MD Plus Bedienungsanleitung

Flowserve

Flowserve D30 Bedienungsanleitung

Flowserve

Flowserve APEX W8000 Betriebsanleitung

Flowserve

Flowserve P4 Bedienungsanleitung

Flowserve

Flowserve D30 Gebrauchsanweisung

Flowserve

Flowserve XL90 Series Leitfaden

Flowserve

Flowserve Logix 3000MD Series Service-Handbuch

Flowserve

Flowserve Logix 3400MD Bedienungsanleitung

Flowserve

Flowserve Logix 520MD Series Montageanleitung

Flowserve

Flowserve Logix 520MD+ Bedienungsanleitung

Flowserve

Flowserve Logix 520MD+ Bedienungsanleitung

Flowserve

Flowserve Logix 500 Series Leitfaden

Flowserve

Flowserve Logix 420 Bedienungsanleitung

Flowserve

Flowserve Logix 3200IQ Service-Handbuch

Flowserve

Flowserve D20 Series Betriebsanleitung

Flowserve

Flowserve Logix 3200MD Montage- und Bedienungsanleitung

Flowserve

Flowserve PMV D20 Betriebsanleitung

Beliebte Ventilstellungsregler Handbücher anderer Marken

Parker

Parker 404XE Series Bedienungsanleitung

Ytc

Ytc TMP-3000 Bedienungsanleitung

PI M-605 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs PXV100AS-F200-SSI-V19 Bedienungsanleitung

RTK

RTK RE 3442 Series Bedienungsanleitung

CVS Controls

CVS Controls 1200 Bedienungsanleitung

Parker

Parker MX80L series Bedienungsanleitung

Westlock

Westlock Quantum 2800 Handbuch

Samson

Samson 3730-0 Service-Handbuch

Samson

Samson TROVIS 3730-3 Service-Handbuch

ESCO Technologies

ESCO Technologies ETS LINDGREN 2302-001 Bedienungsanleitung

SMC Networks

SMC Networks IP8000 Bedienungsanleitung

Samson

Samson FOUNDATION 3730-5 Service-Handbuch

Samson

Samson TROVIS SAFE 3731-3 Service-Handbuch

halstrup-walcher

halstrup-walcher HIPERDRIVE Bedienungsanleitung

ABB

ABB TZIDC Schulungshandbuch

Samson

Samson FOUNDATION 3730-5 Service-Handbuch

halstrup-walcher

halstrup-walcher PS*3**DP series Bedienungsanleitung