Fluidmaster PerforMAX 400CAR3 Bedienungsanleitung

INSTALL WITH CONFIDENCE

QUICK Install Guide

400CAR3

PerforMAX®FILL VALVE & 3” FLAPPER

*See back page for important legal information.

SPANISH - Page 16

2 3

STEP 1: PREPARE TANK

GETTING STARTED

A: TURN OFF WATER

B: DRAIN WATER

Flush toilet to drain most of the water from the tank.

C: USE SPONGE OR TOWEL TO SOAK UP

EXCESS WATER IN TANK

FLUSH

Towel

Sponge

TURN

CLOCKWISE

PARTS OVERVIEW

5403 Universal Adjustable 3” Flapper

PerforMAX™Fill Valve

TOOLS NEEDED

SpongeBucket

Towel Scissors

(Optional)

Locknut

Reﬁll Clip

Reﬁll Tube

Reﬁll Tube Clamp

Shank Washer

Tank Water Level

Adjustment Screw

Bowl Water Level

Adjustment Roller Clamp

STEP 2: REMOVE OLD FILL VALVE

LEFT

A: REMOVE CONNECTOR

Remove water supply

connector from bottom

of ﬁll valve by twisting

connector nut to the left

(clockwise).

B: REMOVE OLD LOCKNUT

Below tank, twist locknut

to the left (clockwise) to

remove from ﬁll valve.

Bucket

(Optional)

Towel

(Optional)

C: REMOVE OLD FILL VALVE

Including reﬁll tube, reﬁll

clip and shank washer.

Drain any excess water

into bucket by removing

ﬁll valve from tank.

(Pull ﬁll valve up)

NOTE: Inspect water

supply connector.

Replace it if it is worn, or

you don’t know how old it is, to

prevent ﬂooding and property damage.

STEP 3: REMOVE OLD FLAPPER

A: REMOVE FLAPPER CHAIN

Pinch clasp to unhook

chain from tank lever.

B: REMOVE FLAPPER FROM

FLUSH VALVE SEAT

Simply unhook or lift ﬂapper

arms off the ﬂush valve

mounting posts, depending

on the type of ﬂapper.

Tank Lever

Mounting

Post

Mounting

Post

6 7

Note: We will adjust the ﬂapper dial in

Step 9 after setting the proper water

level in the tank and bowl.

STEP 4: INSTALL NEW FLAPPER

A: INSTALL NEW FLAPPER

Place ﬂapper on top of ﬂush

valve seat and snap arms onto

ﬂush valve mounting posts.

B: ATTACH FLAPPER CHAIN

TO LEVER

Pinch clasp of clip and attach

the clip to the tank lever

directly above the ﬂapper.

Leave roughly ½ inch of slack

in chain. (small “j” shape)

To adjust chain length, remove

clip and reposition lower on

the chain for shorter length.

STEP 5: ADJUST HEIGHT OF NEW FILL VALVE

1/2” Slack

TIP: A quick and easy way to adjust the chain length.

Take the clip off the chain, dangle the chain through the small part of the clip (A),

then pull both sides of the chain downward until it snaps into place (B).

A B

(SMALL “J” SHAPE)

HOLD

TWIST

LEFT

A: TWIST FILL VALVE TO ADJUST HEIGHT

Top of ﬁll valve cap should measure roughly 3"

above top of overﬂow pipe when installed.

NOTE:

Increasing height allows

more water to ﬁll in the tank.

Do not lift lock ring out of

locked position.

*If the top of your overﬂow pipe is not at least 1” below the bottom of the tank lever hole,

adjust it. If the overﬂow pipe is not adjustable, mark the overﬂow pipe 1” below the bottom

of tank lever hole and using a hacksaw, cut the overﬂow pipe at the speciﬁed mark.

TOP OF FILL VALVE CAP

TOP OF OVERFLOW PIPE

Fill Valve Cap

Overﬂow Pipe

*Lever Hole

Press

Down

8 9

STEP 6: INSTALL NEW FILL VALVE

D: INSTALL LOCKNUT

Screw locknut to the right

(counterclockwise) onto ﬁll valve shank (below tank).

*Hand-tighten only. DO NOT OVER TIGHTEN.

C: ATTACH REFILL CLIP TO OTHER END

OF REFILL TUBE

D: INSERT FILL VALVE

Position reﬁll tube to face ﬂush valve making sure ﬁll

valve parts do not interfere with lever arm.

RIGHT

E: ATTACH REFILL CLIP TO OVERFLOW PIPE

Note: If reﬁll tube is too long to ﬁt inside tank

with lid closed, remove reﬁll tube from ﬁll valve

reﬁll port, cut tube, and reattach to port.

Scissors

(Optional)

TOP

DOWN

VIEW

Reﬁll Tube

Lever Arm

Overﬂow

Pipe

Fill Valve

STEP 7: FINISHING STEPS

A: ATTACH WATER SUPPLY

CONNECTOR TO FILL VALVE

Twist to the right

(counterclockwise)

*Hand-tighten only.

DO NOT OVER TIGHTEN.

RIGHT

C: WATER LEVEL

After the tank stops ﬁlling, water level should ﬁll the tank to

roughly ½ inch below top of overﬂow pipe to ensure a

proper ﬂush. (Does not need to be exact.)

B: TURN ON WATER

Check for leaks.

TURN

COUNTER-

CLOCKWISE

A: INSTALL SHANK WASHER

Pull up to top of shank.

*Place shank washer onto

threaded shank of ﬁll valve.

WIDE SIDE UP.

B: PUSH REFILL TUBE ONTO REFILL

PORT FIRST

Squeeze tube clamp arms and move it

towards reﬁll port.

Shank Washer

Threaded Shank

Reﬁll Clip

Reﬁll Tube

Clamp Arms

Reﬁll

Port

Overtightening may damage ﬁll valve or coupling nut, potentially causing ﬂooding. Make sure

the ﬂoat cup does not touch the tank walls or tank lever and ﬂush valve.

**The top of the overﬂow pipe must be a minimum of 1" below tank lever hole.

1/2"

Overﬂow Pipe

Top of

Overﬂow Pipe

Water Level

**Lever Hole

10 11

STEP 8: FINE-TUNE BOWL WATER LEVEL

A: FLUSH THE TOILET

TO CHECK THE TANK

WATER LEVEL

After the water stops ﬁlling the

tank, the water level should be

roughly ½ inch below the top

of overﬂow pipe to ensure a

proper ﬂush.

B: WATER LEVEL IS TOO LOW

Turn the tank water level adjustment screw

clockwise to raise the ﬂoat. Flush to reset

water level.

WATER LEVEL IS TOO HIGH

Turn the water level adjustment screw

counterclockwise to lower the ﬂoat. Flush

to reset water level.

1/2"

Overﬂow

Pipe

See Step 5C for Full Tank view

Tank Water Level

Adjustment Screw

STEP 9: FINE TUNE FLUSH

–

B: ADJUST FOR MOST

EFFICIENT FLUSH

Continue to adjust dial down one

setting and ﬂush until toilet is unable

to ﬂush paper properly.

Note: Flapper dial is pre-set to

maximum setting (9).

A: TEST FLUSH

Drop 3 squares of toilet paper in

bowl then ﬂush.

C: FINAL SETTING

Once unable to ﬂush paper, adjust dial up one number for

ﬁnal setting.

Hint: The higher the number, the longer the ﬂapper stays open for more

water ﬂushed.

MORE WATER FLUSHED

LESS WATER

FLUSHED

YOU DID IT!

STEP 11: FLUSH THE TOILET

A: FLUSH THE TOILET

If you’re satisﬁed with the ﬂush, YOU’RE DONE!

STEP 10: FINE-TUNE BOWL WATER LEVEL

A: FILL BOWL WITH A GALLON OF WATER

Wait 1 minute until the bowl water level recedes

down and stops.

B: MARK THE WATER LEVEL IN THE BOWL

With a pencil, draw a line at the top of the water level

in bowl. (Pencil mark will easily wash off).

C: FLUSH TOILET TO CHECK BOWL

WATER LEVEL

If the water level matches the line you’ve made in

the bowl when the ﬁll valve stops ﬁlling the tank,

the water level is correct, proceed to Step 8.

TOO HIGH

TOO LOW

If the water level matches the line in the bowl and the

ﬁll valve is STILL FILLING, then the bowl water is

TOO HIGH, proceed to Step 7D.

If the valve shuts off and the water level does NOT

match the line in the bowl, the water level is TOO

LOW, proceed to Step 7D.

E: FLUSH TOILET,

CHECK BOWL WATER LEVEL

Repeat Steps 10D and E until water level in bowl

matches the line when the ﬁll valve shuts off.

D: ADJUST THE BOWL WATER LEVEL

NOTE: “0” on roller clamp equals no reﬁll to bowl.

TOO HIGH =

TOO LOW =

Turn roller clamp with thumb to the

next LOWER number.

Tur n roller clamp with thumb to next

HIGHER number.

Learn more about home sanitation we have.

Inhaltsverzeichnis

Andere Fluidmaster Steuereinheit Handbücher

Fluidmaster

Fluidmaster 400A Bedienungsanleitung

Fluidmaster

Fluidmaster 400A Bedienungsanleitung

Fluidmaster

Fluidmaster PerforMAX 400H Bedienungsanleitung

Fluidmaster

Fluidmaster 402CARHR Bedienungsanleitung

Fluidmaster

Fluidmaster 560AU Bedienungsanleitung

Fluidmaster

Fluidmaster PerforMAX 400H-002 Bedienungsanleitung

Fluidmaster

Fluidmaster PerforMAX 400AH Bedienungsanleitung

Fluidmaster

Fluidmaster 400LS Bedienungsanleitung

Fluidmaster

Fluidmaster 402CARHR Bedienungsanleitung

Fluidmaster

Fluidmaster 200AM133 Bedienungsanleitung

Fluidmaster

Fluidmaster 400AC Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung