Fluidra Astral Pool E35 Bedienungsanleitung

INSTALLATION AND

OPERATING INSTRUCTIONS

E35

Salt Chlorine Generator

INSTALLATION AND OPERATING INSTRUCTIONS I INSTALLATION AND OPERATING INSTRUCTIONS

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

PRECAUTIONS:

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL

This E SERIES SALT CHLORINE GENERATOR must be installed by a licensed or certified electrician or a qualified pool

installer in accordance with the latest edition of the National Electrical Code, NFPA 70(“NEC”) and/or all applicable local

and national codes and ordinances. Installations in Canada must be in accordance with the latest edition of CSA C22.2 –

the Canadian Electric Code, part 1 (“CEC”).

Improper installation could cause an electrical hazard which may result in death or serious injury to pool users, installers

or others due to electrical shock, and/or property damage. Always disconnect power to the Salt Chlorine Generator at the

house circuit breaker before servicing the Salt Chlorine Generator. Failure to do so could result in death or serious injury to

pool users, installers or others. To reduce the risk of injury, do not permit children to use this product.

NOTICE TO USER: This pest control product is to be used only in accordance with the directions on the label. It is an

offence under the Pest Control Products Act to use this product in a way that is inconsistent with the directions on the

label.

WARNING: Heavy pool or spa usage, and higher temperatures may require higher chlorine output to maintain proper free

available chlorine residuals.

Heavy bather loads may trigger the need for additional chlorine to be added to maintain appropriate chlorine

residual in the water.

DO NOT add pool or spa chemicals directly to the skimmer. This may damage the cell.

Maintaining high salt and chlorine levels above the recommended range can contribute to corrosion of pool or

spa equipment.

Check the expiry date of the test kit as test results may be inaccurate if used after that date.

The life expectancy of the electrode is 20,000 hours under normal use conditions.

When replacing the electrode, only use replacement electrodes having a label that clearly states that it is a

replacement electrode for the chlorine-generating device, E35 Salt Chlorine Generator, REGISTRATION

NUMBER 32947, PEST CONTROL PRODUCTS ACT.

For proper sanitation, spas should be completely drained periodically. The number of days between

COMPLETE SPA DRAINAGE is equal to the volume of spa water in litres, divided by 10 times the maximum

number of daily spa users. Refill spa with water and repeat DIRECTIONS FOR USE of the device.

People with a medical condition should consult a physician before entering pool or spa water.

Maximum spa water usage temperature is 40oC. Bathing in spa water at 40oC should not exceed 15 minutes.

WARNING:To reduce the risk of injury, do not permit children to use this product.

WARNING: Risk of Electric Shock. Connect only to a branch circuit protected by a ground fault circuit interrupter

(GFCI). Contact a qualified electrician if you cannot verify that the circuit is protected by a GFCI.

CAUTION: CONNECT ONLY TO A CIRCUIT PROTECTED BY A CLASS A GROUND FAULT CIRCUIT INTERRUPTER. This marking is

to be installed where it is visible during installation.

WARNING: The unit must be connected only to a supply circuit that is protected by a ground fault circuit

interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the

GFCI, push the test button. The GFCI should interrupt power. Push the reset button, power should be restored. If the GFCI

fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button

being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this Salt Chlorine

Generator. Disconnect the Salt Chlorine Generator and have the problem corrected by a qualified service representative

before using.

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

WARNING: To reduce the risk of electric shock, replace damaged cords immediately (where line cord is

permissible by local codes) The installation must conform to the latest edition of the National Electrical Code, NFPA70, for

USA installations, or all applicable provisions of the Canadian Electric Code, CSA C22.2, for Canada

WARNING: High voltage is present in some Salt Chlorine Generator circuits making it mandatory that any

electrical maintenance and repairs be attempted only by properly qualified personnel.

GENERAL OVERVIEW

Congratulations! You have purchased an E35 Salt Chlorine Generator. Please read the instructions carefully and your

purchase will provide you with years of trouble-free use.

Your Salt Chlorine Generator works by converting some of the salt (sodium chloride) in your pool into chlorine which starts

to destroy algae and bacteria and sanitizes your pool. As part of the process, the chlorine is converted back into salt and

hence salt is not consumed.

Your Salt Chlorine Generator control has many features which ensure the simple operation of your Salt Chlorine Generator

and Filtration system.

WARNING: This appliance is not intended for use by persons including young children or infirm persons with

reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

Please ensure that young children are supervised to ensure that they do not play with the pump or the Salt Chlorine

Generator.

WARNING: This Salt Chlorine Generator power supply must be connected to the same source power supply as

the circulating pump provides water flow to the cell. Any isolation switch, time clock or control that operates the

circulating pump must simultaneously operate the Salt Chlorine Generator control.

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

SAVE THESE INSTRUCTIONS

DIRECTIONS FOR USE:

INSTALLATION

The E35 Salt Chlorine Generator control has a rating of IP23 enabling it to be installed outdoors. Regulations require

that the control is not allowed to be located within 3 m (10 ft.) of the pool water.

The E35 Salt Chlorine Generator Control should be installed in a well-ventilated position ideally away from direct

sunlight. Ensure that the unit is not located near pool chemicals as fumes may damage the control.

When installing the control on a post, first attach a flat waterproof panel at least 300 mm (12 in) wide by 500 mm (20 in)

long. Make sure the control is located centrally on the panel and sits flat.

Electrical connection can either be 230 V or 115 V - 10Amp. The AstralPool E-Series is factory set at 230 Volts.

To change the input voltage, simply locate the switch, located at the lower left corner on the controller and slide the

switch to

the right until 115 V wording is visible. It is now set to 115 V input voltage.

CELL INSTALLATION

The Salt Chlorine Generator Cell must be located last in the pipe work just prior to the return to the pool. If valves are

installed between the Salt Chlorine Generator Cell and the pool outlet, it is essential that they cannot deadhead the

pump. If

the pressure in the cell exceeds 350 kPa (50 PSI) and/or the water temperature exceeds 40º C (104º F), the

Cell may fail.

WARNING: Never install the cell before the pump or heater.

The Cell MUST be installed with the barrel unions underneath (water connections pointing downwards) and the cell

should be

horizontal. 50 - 38 mm (2 - 1 ½ in) fittings have been provided. Use a 50 - 38 mm (2 - 1 ½ in) high pressure

PVC pipe and glue into the 50 - 38 mm (2 - 1 ½ in) barrel union tails. Make sure that the O-rings are correctly fitted and

the unions are tightened firmly.

Direction of flow through the Cell is critical –unit must be plumbed with the water entering the cell at the end closest

to the terminal connections (as indicated by flow direction label mounted on cell)

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

WARNING: It is essential that pipe work and equipment do not allow gases generated from the Cell to collect and build up.

WARNING: Cell must be installed Horizontal with water connections pointing downwards –this creates a safety gas

trap. Installation in any other way may cause explosion, injury or death.

WARNING: Cell must be installed in the return pipework to the pool. Always install after filter, gas heater, and solar

heater or heat pump connections.

WARNING: DO NOT install isolation valves on inlet or outlet of cell.

Once the Cell is located, connect the black multi-core cable to the cell. The blue wire must be connected to the blue

terminal.

The cable is designed to come from below the cell. Make sure wing nuts are correctly tightened to ensure

good contact.

POOL PREPARATION

Salt should always be added at the shallow end of the pool and allowed to dissolve. Running the pump will mix the

water and

speed the dissolving process.

WARNING: Never add salt to the skimmer box!!

NOTE: Run the pump for 8-10 hours to ensure the salt is dissolved prior to running the Salt Chlorine Generator.

When the salt is dissolved, run the Pump and Salt System and run it on maximum chlorine output. Check that low salt is

not indicated on the Low Salt indicator Light. If it is, check again in 24 hours. If the low salt indicator still persists, have

the salt

level checked by your local pool shops and ensure it is increased to 3,200 ppm.

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

CHLORINE OUTPUT

To adjust the chlorine output:

(a) Use Increase/Decrease arrows for setting the chlorine output level of the Salt Chlorine Generator. The Salt

Chlorine Generator output can be set from levels 1 through 5.

(b) Chlorine Output display shows the level set

SETTING THE RIGHT CHLORINE OUTPUT AND FILTRATION TIME

Summer

To prevent consumption of chlorine by sunlight, try adding Cyanuric Acid as recommended by your local pool

professional.

Additional benefit will be gained by operating your Salt Chlorine Generator and pump into the evening

when the strong sunlight has abated.

Chlorine is most effective when the pH of your pool water is 7.4. The electro-chemical process of the Salt Chlorine

Generator (change salt into chlorine) will automatically raise the pH of your pool water, so it is very important to check

your pH weekly and adjust as necessary.

Checking Chlorine Level

Ideally, check your Chlorine level in the morning. The free chlorine residual level should be somewhere between 1 and

3 parts per million. Increase or decrease the output of the Salt Chlorine Generator to get the right residual chlorine

level.

STABILIZER

As previously mentioned, sunlight rapidly dissipates the amount of free chlorine in your pool. Chlorine stabilizer greatly

reduces this effect. Without stabilizer, you may need to run your Salt Chlorine Generator at a higher output to maintain

correct chlorine levels.

Swimming Pool

Free available chlorine

1.0 - 3.0 ppm

7.2 - 7.8

Total alkalinity

100 - 120 ppm

Calcium hardness

200 - 300 ppm

Cyanuric acid (stabilizer used in outdoor pools

only)

30 - 50 ppm

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

SALT LEVEL

Salt Level in ppm

Pool Volume (litres)

3,200 ppm

50,000 –85,000 L

4,600 ppm

85,000 –120,000 L

6,000 ppm

120,000 –160,000 L

Initial dosage

We recommend adding 3.2 kg of salt for every 1,000 L of water.

Although salt is not consumed by the E35 Salt Chlorine Generator, salt is lost during backwashing, and rinsing of the

sand filter. A low salt level warning is indicated on your E35 Salt Chlorine Generator if the salt level drops. If LOW SALT

is indicated, check again in 24 hours and then if it is still indicated, add 25 kg (50 lb) of salt to the shallow end of your

pool. Run the filtration system for approx. 6 hours to help mix the salt in the pool. It can take up to a day for the salt to

fully dissolve.

If the LOW SALT light is still on, have the salt level of your pool water tested at your nearest retailer. If the result of the

in-store test indicates a salt level greater than 3,200 ppm, have your Salt Chlorine Generator checked.

WARNING: Never add salt directly to the skimmer box. This practice should

be avoided as it allows very high concentrations of salt to be passed through

your filtration and other pool equipment.

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

SALT CHLORINE GENERATOR MAINTENANCE AND TROUBLESHOOTING

If the supply cord is damaged, it must be replaced by AstralPool or its service agent or a similarly qualified person in

order to

avoid a hazard.

WARNING: Operating the Salt Chlorine Generator with less than 3,000 ppm of dissolved salt in the water may

cause damage to the cell and will void the warranty. Never start Salt Chlorine Generator, until the correct quantity

of salt has been added and dissolved in your pool water.

Cell Maintenance

Your E35 Salt Chlorine Generator has an automatic cleaning feature that, under normal conditions, will keep the cell

plates clear of deposits of salt and calcium.

E35 Salt Chlorine Generator cells have a negative charge sensor that monitors the flow and salt levels of the water. This

sensor is designed to be fail-safe. As it is negative charge sensor, deposits of calcium or other debris may be deposited

on it and cause it to indicate a low salt or no flow condition. Should a low salt condition be indicated, have your salt level

checked at your local pool shop. If the low salt condition persists, or a no flow condition is indicated when the supply

pump is operating, you may need to manually clean your Salt Chlorine Generator Cell.

Cell Cleaning Instructions:

Close applicable valves.

Disconnect the Salt Chlorine Generator from the Mains by a circuit breaker.

Disconnect the cell wires.

Undo the barrel nuts connecting the cell to your filtration system.

Turn the cell upside down (inlet and outlet on top) and fill the cell with a cell cleaning solution, sold at your pool

retailer.

Repeat if necessary and then rinse well in clean water.

Reinstall the cell ensuring O-rings are correctly located and barrel nuts are tightened to prevent leaks.

Reconnect cell wires with wing nuts supplied making sure the blue wire is connected to the blue terminal.

Incorrect connection may damage your Salt Chlorine Generator control. Tighten wing-nuts to ensure the

electrical connection is sound.

Return all valves to their normal positions; reconnect power at the circuit breaker.

WARNING: Follow safety instructions provided with the cell cleaning solution. The use of eye protection, mask

and gloves are highly recommended.

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

MAINTENANCE OF YOUR SALT CHLORINE GENERATOR

Maintenance Schedule: Your new product incorporates moving parts and withstands high velocity water with

chemicals in it. Some of these parts will wear in the normal course of use and require regular checks and

maintenance. Performing these checks and maintenance will identify parts that have worn and require

repair/replacement before further serious damage is sustained. A small amount of regular care and attention to

your

pool equipment will help ensure long life and trouble-free performance.

To protect against extremes of temperature, your unit is vented to allow expensive electronics to cool. Ants and

some

insects are often attracted to the warmer, dry environment inside the enclosure. We recommend that,

with power

turned off, you spray a surface insecticide on the surfaces surrounding the control to prevent ant and

insect ingress.

Repeat every three months or as necessary.

Timing

Maintenance Check

Service action (if required)

Every 2 Weeks

Check cell for calcium build up

Check water chemistry

Check cable connections to cell

If required, soak electrode in cell cleaning

solution. Use a soft brush.

Balance pH in pool and adjust output of

unit

to ensure satisfactory production of

chlorine.

Ensure no water contact is occurring with

pins.

Every 3 Months

Check cell connections for leaks

Check for insects/ ants

Isolate Pump, turn power off, clean and

grease O-rings or replace if necessary.

Spray a surface insecticide on the

surfaces

around the unit to prevent

ant and insect

ingress.

Important note: Regular maintenance is important to ensure long life and trouble-free performance of your pool

equipment.

If unable to perform the maintenance yourself, contact your local AstralPool office who will arrange a

trained service technician to perform the maintenance for you.

Record your Equipment details here for quick reference:

Model No:

Serial No:

Inst date:

INST 385 E35 SALT CHLORINE GENERATOR (10-2018)

TROUBLESHOOTING

Your E35 Salt Chlorine Generator has diagnostic and safety features to make it easy to maintain your system.

The

table below summarizes potential faults and their causes.

Fault Indication

Potential Causes

Remedies

No Flow

Pump turned off/disconnected or

valves

closed

Blue wire disconnected from cell

Ensure valves/pump on

Connect Blue sense wire to cell

Low salt

Salt level in pool has dropped too low

Pool water temperature is low

Cell has calcified

Cell or control has failed

Take sample of water to pool

shop and check salt level –

add

salt as recommended.

Add salt and turn Salt

Chlorine Generator output

down until the water is

warmer.

Clean cell

Call for Service

Display blank

No Power to Controller

Fuse blown

Plug in controller and

ensure

main power is

available

Have a service technician

replace fuse (3 amp slow

blow)

Low/No chlorine

pool

Cables not connected to cell

Timer period too short

Chlorine output level too low

Filter needs backwashing

pH too high

Pool stabilizer (cyanuric acid) too low

Salt level too low

Connect cables

Increase timer period –

particularly in summer

Increase chlorine output

Backwash filter

Balance pH level to 7.2 –7.8

Increase Stabilizer between

and 50 ppm

Increase salt to above 3,200 ppm

Distributed by:

RBF International Ltée

780, Nobel Street

Saint-Jérôme (Québec) Canada J7Z 7A3

450 438-4416

Inhaltsverzeichnis

Andere fluidra Wechselrichter Handbücher

fluidra

fluidra Certikin iSAVER+ DVSD03 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung

fluidra Astral Pool E35 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken