Fluke 990-GM/2 Bedienungsanleitung

PN 2555277

May 2006, Rev. 1, 2/07

All product names are trademarks of their respective companies.

990-GM/2

ADSLx Golden Modem

Quick Reference Guide

General Description

The 990-GM/2 (Golden Modem) appliqué is used with the CopperPro 990 DSL

Modem Test for testing ADSL, ADSL2, and ADSL2+ services. It contains an industry-

standard ADSL/2/2+ modem (ATU-R) that is housed in a compact metal case and

carried in the front pouch of the 990 softcase. The pouch flap can be opened for

connecting the Ethernet cable or for viewing the GM/2 Status indicators.

GM/2 Status Indicators

•POWER: green LED that is located in the upper right corner of the ENET jack.

Indicates that the 990 has applied power to the GM/2 during operation of the

DSL Modem Test.

•SYNC: green LED that is located in the upper left corner of the ENET jack.

Indicates the following:

•Flashing (slow or fast): the GM/2 is in the process of training with a far-end

ADSLx DSLAM modem via the DSL Test Cord.

•Steady: the GM/2 has trained with a DSLAM modem, and link statistics are

available.

GM/2 Connectors

990: RS232 control / power jack that is connected with a flat cable to the 990.

The cable is secured to the GM/2 990 jack and removable at the 990 serial port.

This allows you to plug a standard serial cable into the 990 for downloading

new program versions or uploading stored data files to a PC.

DSL: RJ11 jack that is connected with the attached DSL Test Cord to the line

under test. The DSL Test Cord (RJ11-to-RJ11/Test Clip cable) is coiled inside the

Test Lead pouch. It is connected to the line under test either by attaching the Tip

and Ring clips to a wiring terminal or by inserting the RJ11 plug into the NID

connector or house wiring RJ11 jack.

ENET: RJ45 jack that is used to connect the supplied Ethernet cable to a PC.

Running a DSL Modem Test

To run a DSL Modem Test:

1. Disconnect the subscriber’s ADSLx modem from the line under test.

2. Connect the GM/2 DSL Test Cord (coiled inside the 990’s Test Lead pouch) to

the subscriber’s line, using either the cable’s RJ11 plug or the Red & Black

(Ring & Tip) test clips.

3. Turn on the 990.

4. Select DSL Modem Test from the CopperPro 990 Main menu. Press

Setups and enable the desired emulation modes.

Note

The default enables all modes.

5. Press TEST.

The primary Modem Results screen is displayed. Results fields are blank.

An hourglass (in the lower left corner) indicates that the test is in progress.

The Modem Status line in the upper right corner displays the real-time

status of the process:

a. Power Up: the 990 is applying power to the GM/2 (POWER LED is

on).

b. Booting: the GM/2 is booting its operating system.

c. Connecting: the GM/2 is training with the far end DSLAM (SYNC

LED flashes slow, then fast).

d. Showtime: the GM/2-DSLAM link is up and statistics are available

for retrieval (SYNC LED is on steady).

e. Test Completed: link statistics are displayed (SYNC LED is on

steady).

Primary link statistics are available on Page 1 of the Modem Results screen

and secondary statistics are listed on Page 2 (to display, use the More

softkey).

6. To refresh the Modem Test results screen, press TEST again.

7. To change the modem emulation mode(s), press Setups. Then, press TEST.

The GM/2 will reconnect with the DSLAM in the new mode.

8. To save both pages of results, press the Save Results softkey. Enter the

Cable, Pair, and Telephone Number in the appropriate fields.

9. Press the Bits / Bin softkey on the primary Modem Results screen to

retrieve encoding data from the GM/2 and to display the associated graph.

This graph shows the number of bits encoded at each DMT bin. It is viewed

and operated in the same manner as the 990 ADSL Auto-Test Bits / Bin

graph. Refer to the 990 Users Guide for details.

If the GM/2 fails to establish a link with the DSLAM, a communications error

message is displayed, and the speaker chirps to signal a failure.

10. To initiate another connection attempt, press TEST again.

11. To remove GM/2 power or to reset and re-initialize the modem, press BACK

from the primary Modem Results screen.

This returns you to the Main menu.

The GM/2 is powered until the DSL Modem Test program is exited, allowing

you to conduct subsequent tests without the initial “booting” delay.

Note

To conserve 990 battery power, limit the time spent in active mode or

connect to the external charger while testing.

12. To ping the network, press the Ping softkey on the secondary Modem

Results screen. Then, do the following:

a. Press the Setups softkey.

b. Enter Ping Setups information (see 990DSL Series II Users Guide

for Ping setup details).

c. Press TEST.

Network ping test results are displayed.

13. After a successful connection, the GM/2 can be used to access the Internet

over the subscriber’s ADSLx line:

a. Connect the supplied Ethernet cable between the GM/2 ENET jack

and the Ethernet port of a PC.

b. Access the web via a standard browser program.

Specifications

Size: 4.2 x 6.6 x 1.3 in. (11x17x3.3 cm)

Weight: 12.8 oz. (364 g)

Operating Temperature: -4o F to +140o F (-20ο C to +60o C)

Storage Temperature: -40o F to +158o F (-40o C to +70o C)

DC Input Voltage: +6 to +15 VDC

DC Input Current (Standby Mode): 210 mA@ 8VDC (Typ.)

DC Input Current (Active Mode): 420 mA @ 8VDC (Typ.)

990 Battery Operating Time (Active Mode) 4 Hours Continuous (Typ.)

ADSL Standards Compliance (ATU-R):

ADSL ANSI

ADSL G.DMT

ADSL G.Lite

ADSL2

ADSL2+

ANSI T1.413 Issue 2

ITU G.992.1a, b

ITU G.992.2ab

ITU G.992.3a, b, l, m

ITU G.992.5a, b

Regulatory Compliance: CSA: C22.2 No 1010.1

CE: EN 61326 Class A

CE: EN61010-1

DSL Connector Pinout:

Pin 3, 4

Pins 1, 2, 5, 6

DSL Tip, Ring

Not Used

ENET Connector Pinout:

Pin 1, 2

Pin 3, 4

Pins 4, 5, 7, 8

Ethernet Rx+, Rx-

Ethernet Tx+, Tx-

Not Used

990 Software Version Required: 3.21.16 (or greater)

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Fluke Networks mainframe products will be free from defects in material and workmanship for

one year from the date of purchase. Parts, accessories, product repairs and services are

warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or

other peripherals are all considered parts or accessories. This warranty does not cover damage

from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation

or handling. Resellers are not authorized to extend any other warranty on Fluke Networks’

behalf. To obtain service during the warranty period, contact your nearest Fluke Networks

authorized service center to obtain return authorization information, then send your defective

product to that Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A

PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE NETWORKS IS NOT LIABLE FOR

ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING

FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or

limitation of an implied warranty or of incidental or consequential damages, this limitation of

liability may not apply to you.

Fluke Networks

PO Box 777

Everett, WA 98206-0777

USA

4/04

Inhaltsverzeichnis

Andere Fluke Modem Handbücher

Fluke

Fluke 2635A-RF900USB Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung