Fluke 110 Bedienungsanleitung

Models 110, 111 & 112

True RMS Multimeters

Users Manual

November 2000 (English), Rev.2, 3/04

Limited Warranty and Limitation of Liability

Each Fluke product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is three years and

begins on the date of shipment. Parts, product repairs, and services are warranted for 90 days. This warranty extends only to the original buyer or end-user

customer of a Fluke authorized reseller, and does not apply to fuses, disposable batteries, or to any product which, in Fluke's opinion, has been misused, al-

tered, neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling. Fluke warrants that software will operate substantially

in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Fluke does not warrant that software

will be error free or operate without interruption.

Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or differ-

ent warranty on behalf of Fluke. Warranty support is available only if product is purchased through a Fluke authorized sales outlet or Buyer has paid the applica-

ble international price. Fluke reserves the right to invoice Buyer for importation costs of repair/replacement parts when product purchased in one country is sub-

mitted for repair in another country.

Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase price, free of charge repair, or replacement of a defective product which is

returned to a Fluke authorized service center within the warranty period.

To obtain warranty service, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that service

center, with a description of the difficulty, postage and insurance prepaid (FOB Destination). Fluke assumes no risk for damage in transit. Following warranty

repair, the product will be returned to Buyer, transportation prepaid (FOB Destination). If Fluke determines that failure was caused by neglect, misuse, contami-

nation, alteration, accident, or abnormal condition of operation or handling, including overvoltage failures caused by use outside the product’s specified rating, or

normal wear and tear of mechanical components, Fluke will provide an estimate of repair costs and obtain authorization before commencing the work. Following

repair, the product will be returned to the Buyer, transportation prepaid, and the Buyer will be billed for the repair and return transportation charges (FOB Ship-

ping Point).

THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE SHALL NOT BE LIABLE

FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE

OR THEORY.

Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the

limitations and exclusions of this warranty may not apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other

decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Table of Contents

Title Page

Read Before Using the Meter: Warnings and Precautions .................................................... ii

Contacting Fluke ................................................................................................................... 1

"Warning" and "Caution" Statements..................................................................................... 1

Unsafe Voltage...................................................................................................................... 1

Test Lead Alert...................................................................................................................... 1

Battery Saver ("Sleep Mode")................................................................................................ 2

Terminals .............................................................................................................................. 2

Rotary Switch Positions......................................................................................................... 2

Display .................................................................................................................................. 3

MIN MAX AVG Recording Mode ........................................................................................... 4

Display HOLD ....................................................................................................................... 4

Backlight (Model 112 Only) ................................................................................................... 4

Manual Ranging and Auto Ranging....................................................................................... 5

Power-Up Options................................................................................................................. 5

Making Basic Measurements ................................................................................................ 6

Measuring AC and DC Voltage ........................................................................................ 6

Understanding AC Zero Input Behavior of True RMS Meters ........................................... 6

AC current: below 5% of 60 mA AC, or 3 mA AC ............................................................. 6

Measuring Resistance...................................................................................................... 7

Measuring Capacitance.................................................................................................... 7

Testing for Continuity ....................................................................................................... 8

Testing Diodes ................................................................................................................. 8

Measuring AC or DC Current (Models 111 and 112) ........................................................ 9

Measuring Frequency....................................................................................................... 9

Using the Bar Graph.............................................................................................................. 10

Cleaning................................................................................................................................ 10

Testing the Fuse (Models 111 and 112) ................................................................................ 11

Replacing the Battery and Fuse ............................................................................................ 11

Specifications........................................................................................................................ 12

Models 110, 111 & 112

Users Manual

WRead Before Using the Meter: Warnings and Precautions

To avoid possible electric shock or personal injury, follow these guidelines:

•Use the Meter only as specified in this manual or the protection provided by the Meter might be impaired.

•Do not use the Meter or test leads if they appear damaged, or if the Meter is not operating properly.

•Always use proper terminals, switch position, and range for measurements.

•Verify the Meter's operation by measuring a known voltage. If in doubt, have the Meter serviced.

•Do not apply more than the rated voltage, as marked on Meter, between terminals or between any terminal and earth ground.

•Use caution with voltages above 30 V ac rms, 42 V ac peak, or 60 V dc. These voltages pose a shock hazard.

•To avoid false readings that can lead to electric shock and injury, replace the battery as soon as the low battery indicator (N) appears.

•Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance.

•Do not use the Meter around explosive gas or vapor.

•When using test leads or probes, keep your fingers behind the finger guards.

•Remove test leads from Meter before opening the battery door or Meter case.

Symbols

BAC (Alternating Current) IFuse

FDC (Direct Current) PConforms to European Union directives

DAC or DC $Canadian Standards Association

JEarth ground TDouble insulated

WImportant information; Refer to manual t

950 Z Listed

Underwriters Laboratories, Inc.

N Battery (Low battery when shown on display) ;

N10140

Conforms to relevant Australian standards

s Inspected and licensed by TÜV Product Ser-

vices #VDE (Verband Deutscher Electroniker)

Models 110, 111 & 112

True RMS Multimeters

The Fluke Model 110, Model 111, and Model 112 are battery-

powered, true-RMS multimeters (hereafter "the Meter") with a

6000-count display and a bar graph. This manual applies to all

three models. All figures show the Model 112.

The Meter measures or tests the following:

•AC / DC voltage and current

•Resistance

•Continuity

•Diodes

•Voltage and current frequency

•Capacitance

These meters meet CAT III IEC 61010-1-95 standards. The IEC

61010-1-95 safety standard defines four overvoltage categories

(CAT Ito IV) based on the magnitude of danger from transient

impulses. CAT III meters are designed to protect against

transients in fixed-equipment installations at the distribution level.

Contacting Fluke

To contact Fluke, call:

USA: 1-888-99-FLUKE (1-888-993-5853)

Canada:1-800-36-FLUKE (1-800-363-5853)

Europe: +31 402-675-200

Japan: +81-3-3434-0181

Singapore +65-738-5655

Anywhere in the world: +1-425-446-5500

Visit Fluke's web site at: www.fluke.com.

"Warning" and "Caution" Statements

A "WWarning" statement identifies hazardous conditions and

actions that could cause bodily harm or death.

A "Caution" statement identifies conditions and actions that could

damage the Meter or the equipment under test.

Unsafe Voltage

To alert you to the presence of a potentially hazardous voltage,

the Ysymbol is displayed when the Meter detects a voltage

≥30 V or a voltage overload (OL) condition.

Test Lead Alert

WWarning

Personal injury or damage to the Meter can occur if you

attempt to make a measurement with a lead in an

incorrect terminal.

To remind you to check that the test leads are in the correct

terminals, LEAd is displayed briefly when you move the rotary

switch to or from any Aposition.

Models 110, 111 & 112

Users Manual

Battery Saver ("Sleep Mode")

The Meter automatically enters "Sleep mode" and blanks the

display if there is no function change or button press for 20

minutes. To disable the Sleep mode, hold down the Hz button

while turning the Meter on. The Sleep mode is always disabled in

the MIN MAX AVG mode.

Terminals

10 A

FUSED

COM

aej01f.eps

Item Description

Input terminal for AC and DC current measurements to

10 A, or to 20 A overload for 30 seconds maximum

(Models 111 and 112 only), and for frequency of

current.

Common (return) terminal for all measurements.

Input terminal for voltage, continuity, resistance, diode

test, capacitance, and voltage frequency

measurements.

Rotary Switch Positions

Switch Position Measurement Function

Hz (button)

AC voltage from 300 mV to 600 V.

Frequency from 5 Hz to 50 kHz.

Hz (button)

DC voltage from 1 mV to 600 V.

Frequency from 5 Hz to 50 kHz.

RBeeper turns on at <20 Ωand turns off

at >250 Ω.

eOhms from 0.1 Ωto 40 MΩ.

GDiode test. Displays OL above 2.4 V.

EFarads from 1 nF to 9999 µF.

(Models 111 & 112)

Hz (button)

AC current from 3 A to 10 A.

(20 A overload for 30 seconds maximum.)

>10.00 display flashes.

>20 A, OL is displayed.

Frequency from 50 Hz to 5 kHz.

(Models 111 & 112)

Hz (button)

DC current from 0.001 A to 10 A.

(20 A overload for 30 seconds maximum.)

>10.00 display flashes.

>20 A, OL is displayed.

Frequency from 50 Hz to 5 kHz.

Notes: AC voltage and current AC-coupled, True RMS, up to 500 Hz.

True RMS Multimeters

Display

13 14 15

aej02f.eps

No. Symbol Meaning

s Meter is set to continuity function.

R Diode test.

O Negative readings.

Y Unsafe voltage. Voltage ≥30 V, or

voltage overload condition (OL).

Display HOLD is enabled. Display

freezes present reading.

In MIN MAX AVG mode, MIN MAX

AVG recording is paused.

X W V

MIN MAX AVG mode enabled.

Maximum, minimum, or average

reading displayed.

No. Symbol Meaning

7 nµF mVA

MkekHz

Measurement units.

8 DC AC Direct current, alternating current.

9 N Replace battery immediately.

10 610000 mV All possible segments of the range

annunciator.

11 (Bar graph) Analog display.

12 Auto Range

Manual Range

The Meter selects the range with the

best resolution.

The user selects the range.

13 ± Bar graph polarity.

14 0L The input is too large for the range.

15 LEAd WTest lead alert.

Displayed briefly when rotary switch

is moved to or from any Aposition.

Error Messages

diSC Displayed while the capacitor discharges. In

Capacitance function only.

EEPr Cannot read data from EEPROM. Turn power off,

then on. If message remains, service Meter.

EEPr

Err

Invalid EEPROM data. Have Meter serviced.

CAL

Err

Invalid calibration data. Calibrate Meter.

Models 110, 111 & 112

Users Manual

MIN MAX AVG Recording Mode

The MIN MAX AVG recording mode captures the minimum and

maximum input values, and calculates a running average of all

readings. When a new high or low is detected, the Meter beeps.

Put the Meter in the desired measurement function and range.

⇒Press MIN MAX to enter MIN MAX AVG mode.

mand MAX are displayed and the highest reading

detected since entering MIN MAX AVG is displayed.

⇒Press MIN MAX to step through the low (MIN), average

(AVG), and present readings.

⇒To pause MIN MAX AVG recording without erasing stored

values, press HOLD. his displayed.

⇒To resume MIN MAX AVG recording, press HOLD again.

⇒To exit and erase stored readings, press MIN MAX for at least

one second or turn the rotary switch.

Display HOLD

WWarning

To avoid electric shock, when Display HOLD is

activated, be aware that the display will not change

when you apply a different voltage.

In the Display HOLD mode, the Meter freezes the display.

⇒Press HOLD to activate Display HOLD. (his displayed.)

⇒To exit and return to normal operation, press HOLD or turn the

rotary switch.

Backlight (Model 112 Only)

Press Sto toggle the backlight on and off. The backlight

automatically turns off after 2 minutes.

To disable the automatic 2-minute backlight timeout, hold down

the Sbutton while turning the Meter on.

True RMS Multimeters

Manual Ranging and Auto Ranging

The Meter has both Manual Range and Auto Range modes.

⇒In the Auto Range mode, the Meter selects the range with the

best resolution.

⇒In the Manual Range mode, you override Auto Range and

select the range yourself.

When you turn the Meter on, it defaults to Auto Range and Auto

Range is displayed.

1. To enter the Manual Range mode, press RANGE. Manual

Range is displayed.

2. In the Manual Range mode, press RANGE to increment the

range. After the highest range, the Meter wraps to the lowest

range.

Note

You cannot manually change the range in the

MIN MAX AVG or Display HOLD modes.

If you press RANGE while in MIN MAX AVG or Display

Hold, the Meter beeps, indicating an invalid operation, and

the range does not change.

3. To exit Manual Range, press RANGE for at least 1 second or

turn the rotary switch.

The Meter returns to Auto Range and Auto Range is

displayed.

Power-Up Options

To select a Power-Up Option, hold down the button indicated for

at least 1 second while turning the Meter on.

Power-Up Options are canceled when you turn the Meter off and

when sleep mode is activated.

Button Power-Up Options

HOLD

Turns on all display segments.

Release HOLD to continue; the software version

number is displayed briefly and the Meter resumes

normal operation.

MIN MAX Disables beeper.

Hz Disables automatic power-down ("Sleep mode").

SDisables automatic 2-minute backlight timeout.

(Model 112 Only)

Models 110, 111 & 112

Users Manual

Making Basic Measurements

The figures on the following pages show how to make basic

measurements.

When connecting the test leads to the circuit or device, connect

the common (COM) test lead before connecting the live lead;

when removing the test leads, remove the live lead before

removing the common test lead.

WWarning

To avoid electric shock, injury, or damage to the Meter,

disconnect circuit power and discharge all high-voltage

capacitors before testing resistance, continuity, diodes,

or capacitance.

Note

In reading AC voltage or current, for the integrated RMS

converter to correctly measure distorted waveforms, reading

settling time increases to several seconds at the low end of

AC voltage and current ranges.

Because inputs below 5% of range are not specified, it is

normal for this meter to display non-zero readings when the

test leads are disconnected from a circuit or are shorted

together.

Measuring AC and DC Voltage

Volts DCVolts AC

aej03f.eps

Understanding AC Zero Input Behavior of True RMS Meters

Unlike averaging meters, which can accurately measure only pure

sinewaves, True RMS meters accurately measure distorted

waveforms. Calculating True RMS converters require a certain

level of input voltage to make a measurement. This is why AC

voltage and current ranges are specified from 5% of range to

100% of range. Non-zero digits that are displayed on a True RMS

meter when the test leads are open or are shorted are normal.

They do not affect the specified AC accuracy above 5% of range.

The input levels that are unspecified are:

•AC voltage: below 5% of 6000 mV AC, or 300 mV AC

•AC current: below 5% of 60 A AC, or 3.00 A AC

Andere Handbücher für 110

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fluke Multimeter Handbücher

Fluke

Fluke 8030A Bedienungsanleitung

Fluke

Fluke a3002 FC Gebrauchs- und Pflegehandbuch

Fluke

Fluke 88 V Bedienungsanleitung

Fluke

Fluke CNX C3000 Bedienungsanleitung

Fluke

Fluke 27 Bedienungsanleitung

Fluke

Fluke 8506A Bedienungsanleitung

Fluke

Fluke 83V Bedienungsanleitung

Fluke

Fluke 77 Gebrauchs- und Pflegehandbuch

Fluke

Fluke J 39200 Bedienungsanleitung

Fluke

Fluke 79 Bedienungsanleitung

Fluke

Fluke 8845A Bedienungsanleitung

Fluke

Fluke 287 Bedienungsanleitung

Fluke

Fluke LinkRunner Pro LRPRO-1000 Bedienungsanleitung

Fluke

Fluke 8062A Bedienungsanleitung

Fluke

Fluke 114 Bedienungsanleitung

Fluke

Fluke 718Ex 30G Bedienungsanleitung

Fluke

Fluke 183 Bedienungsanleitung

Fluke

Fluke 12B/18 Bedienungsanleitung

Fluke

Fluke 374 Gebrauchs- und Pflegehandbuch

Fluke

Fluke i410 Bedienungsanleitung

Fluke

Fluke 113 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 771 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 8505A Bedienungsanleitung

Fluke

Fluke 8845A Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Bedienungsanleitung